GrizzlyメーカーG3183の使用説明書/サービス説明書
ページ先へ移動 of 26
HOLLOW CHISEL MORTISER MODEL G3183 INSTRUCTION MANUAL COPYRIGHT © NOVEMBER, 1994 BY GRIZZLY IMPORTS, INC. REG. TX 3 926 489 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY IMPORTS, INC.
.
G3183 Hollow Chisel Mortiser -1- Table Of Contents PAGE 1. INTRODUCTION ........................................................................................................2 SAFETY RULES FOR ALL TOOLS ..............................................
-2- G3183 Hollow Chisel Mortiser Grizzly Imports, Inc. is proud to offer the Model G3183 Hollow Chisel Mortiser. This Model G3183 is a part of Grizzly’s growing family of fine wood- working machinery. When used according to the guidelines stated in this manual, you can expect years of trouble-free, enjoyable operation.
G3183 Hollow Chisel Mortiser -3- 12. USE SAFETY GLASSES AND EAR PRO- TECTION. Also use a DUST MASK if the operation is dusty. 13. DO NOT OVERREACH. Keep proper footing and balance at all times. 14. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest performance.
-4- G3183 Hollow Chisel Mortiser Unpacking The Model G3183 Hollow Chisel Mortiser is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, please call Customer Service immediately for advice.
G3183 Hollow Chisel Mortiser -5- Clean up The column and other unpainted parts of the Model G3183 are coated with a waxy oil that pro- tects them from corrosion during shipment. Remove the protective coating with mineral spir- its and paper towels. Do not use gasoline or other petroleum based solvents because of their extremely low flash points.
-6- G3183 Hollow Chisel Mortiser Circuit Requirements The motor supplied with the Model G3183 is a 110V single-voltage motor, prewired for 110V. Under normal use, the motor draws approximate- ly 6 amps @ 110V. We recommend using a 15 amp circuit breaker or a 15 amp slow blow fuse for 110V operation.
G3183 Hollow Chisel Mortiser -7- SECTION 2: ASSEMBLY Hydraulic Cylinder To install the Hydraulic Cylinder: 1. Screw the handle bar into the adjustable gear on the right side of the mortising machine and raise the head to its highest position. Figure 1.
-8- G3183 Hollow Chisel Mortiser Table To install the table: 1. Position the wood table on the base and secure with two screws provided. Figure 3. 2. Secure the machine to a suitable work surface by fastening bolts through the holes provided in the mortiser’s base.
G3183 Hollow Chisel Mortiser -9- Hold Down To install the hold down: Slide the hold down assembly over the vertical post so the fingers extend forward of the fence over the table. Leave the setscrew loose for now. Figure 5. Figure 5. Figure 6. Figure 7.
Figure 8. Figure 9. -10- G3183 Hollow Chisel Mortiser 5. Feed the bit into the chuck until the tip of the bit extends between 1 ⁄ 16 '' and 3 ⁄ 16 '' below the tip of the chisel edge. Once you have prop- erly aligned the bit and chisel, tighten the chuck with the chuck key provided in the package.
G3183 Hollow Chisel Mortiser -11- Figure 10. Chuck Extender The use of the chuck extender is only necessary if the chisel is too short to reach the chuck.
-12- G3183 Hollow Chisel Mortiser Headstock SECTION 3: ADJUSTMENTS The handle bar on the Model G3183 Hollow Chisel Mortiser raises and lowers the head by rack-and-pinion gearing.
G3183 Hollow Chisel Mortiser -13- Hold Down The hold down is designed to prevent the work- piece from lifting when the chisel is retracted. The hold down should be adjusted so it just comes in contact with the workpiece – allowing it to move side-to-side, but not up and down.
-14- G3183 Hollow Chisel Mortiser Head Adjustment Proper adjustment of the head and column is necessary to ensure that mortiser travel is smooth and precise. Two bolts located at the back of the head control the tightness of the head and column. If movement of the head becomes sloppy, tighten the bolts until the travel is smooth and solid.
G3183 Hollow Chisel Mortiser -15- Caution Always wear ANSI-approved safety glasses or goggles when operating equipment. Do not allow visitors into your workshop when testing or oper- ating equipment.
-16- G3183 Hollow Chisel Mortiser Once the assembly is complete and the adjust- ments are done to your satisfaction, you are ready to test the machine. Turn on the power supply at the main panel. Press the START button. Make sure that your fin- ger is poised on the STOP button, just in case there’s a problem.
G3183 Hollow Chisel Mortiser -17- Figure 18. 12 34 56 6. The chisel and bit will cause some smoking as it contacts the workpiece. This is caused by friction heating resins in the wood. This does not necessarily mean that the chisel is dull. More likely, a dull chisel will cause the head to be difficult to lower.
-18- G3183 Hollow Chisel Mortiser SECTION 5: MAINTENANCE Lubrication The Model G3183 Hollow Chisel Mortiser requires a minimum of maintenance. The opera- tor should clear the machine of wood chips after every use and periodically wipe the machine of dust and grime.
G3183 Hollow Chisel Mortiser -19- The following pages contain general machine data, parts diagram, parts list, troubleshooting guide and Warranty/Return information for your Model G3183 Hollow Chisel Mortiser.
107 143 149 150 131 127 120 138 111 132 128 119 126 129 122 118 140 141 117 137B 137A 105 115 136 114 113 139 130 125 123 110 109 104 103 102 116 101 105 145 146 147 148 112 121 142 144 106 153 152 15.
REF PART # DESCRIPTION REF PART # DESCRIPTION G3183 Hollow Chisel Mortiser -21- 101 P3183001 CASTING BASE 102 PLW04M LOCK WASHER 8mm 103 PSB14M CAP SCREW M8-1.25x20mm 104 P3183104 COLUMN 105 PSS16M SETSCREW M8-1.25x10mm 106 P3183006 HEADSTOCK 107 P3183007 DEPTH STOP ROD 108 P3183008 MOTOR 109 P3183009 RACK 110 PSB26M CAP SCREW M6-1.
-22- G3183 Hollow Chisel Mortiser MACHINE DATA GRIZZLY MODEL G3183 HOLLOW CHISEL MORTISER Design Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bench Model Overall Dimensions Base Size . . .
G3183 Hollow Chisel Mortiser -23- TROUBLESHOOTING GUIDE Noisy operation Dry drill bit shaft Lubricate drill bit shaft Bit burns or smokes 1. Chips not coming out of hole 1. Retract bit frequently to clear chips 2. Dull bit 2. Sharpen or replace bit 3.
-24- G3183 Hollow Chisel Mortiser Grizzly Imports, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, neg- ligence, accidents, repairs or alterations or lack of maintenance.
デバイスGrizzly G3183の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Grizzly G3183をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGrizzly G3183の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Grizzly G3183の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Grizzly G3183で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Grizzly G3183を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGrizzly G3183の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Grizzly G3183に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGrizzly G3183デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
