GrizzlyメーカーH8259の使用説明書/サービス説明書
ページ先へ移動 of 36
MO DE L H8259 1 0 " x 1 8 " B ENC HT OP L A TH E O WNER'S MANU A L COPYRIGHT © OCTOBER, 20 07 BY GRIZ ZL Y INDUSTR IAL, INC. W AR NI NG : NO PORT IO N O F TH IS MA NUAL M A Y B E R EPROD UCED IN AN Y S HAPE OR FO RM WIT HOU T T HE WRI T TEN APPROV AL OF G RI ZZ L Y I NDU STR IAL , IN C.
.
INTRODUCTION ............................................................................................................................... 2 Foreword ...................................................................................................
-2 - H8259 1 0" x 1 8" Benchtop Lathe INTR ODU CTION F ore w ord We are proud to offer the Model H8259 10" x 18" Benchtop Lathe. This machine is part of a grow - ing Grizzly family of fine woodworking machinery.
H8259 1 0" x 1 8 " Benc htop L athe -3 - .
- 4- H8259 1 0" x 1 8" Benchtop Lathe .
H8259 1 0" x 1 8 " Benc htop L athe -5 - Figure 1. Model H8259 Identification. Identi fi cat ion A. Headstock B. Faceplate C. Spur Center D. Tool Rest E. Tool Rest Lock Handle F. Tool Rest Base Release Lever G. Live Center H. Quill Lock Handle I.
- 6 - H8259 1 0" x 1 8" Benchtop Lathe .
H8259 1 0" x 1 8 " Benc htop L athe - 7 - .
-8- H8259 1 0" x 1 8 " Benc htop L athe A ddit ion al Safety f or W ood Lat hes 1. KEEPING GUARDS IN PLACE. Make sure all guards are in place and that the lathe sits on a flat, stable surface. 2. EYE/FACE PROTECTION. Always wear eye protection or a face shield when operat - ing the lathe.
H8259 1 0" x 1 8 " Benc htop L athe -9 - Figure 2. T ypical t ype 5- 1 5 plug and receptacle. Serious perso nal injur y could occur if y ou connect the machine to t he power source before you ha ve compl eted the set up p ro - cess . DO NOT conne ct t he machine to the power source until instructe d to do so.
- 1 0 - H8259 1 0" x 1 8" Benchtop Lathe W e ar safety glas ses dur- ing t he entir e setup pr o - cess ! Th is ma chin e pr es en ts se ri ous inj ur y h az a rds to untrained users .
H8259 1 0" x 1 8 " Benc htop L athe - 1 1 - Wo rkb enc h Load Refe r to the Machine Da ta She et for the weight and foot pri nt spe cifi cati ons of your ma chin e. Some workbenches ma y require additional rein - forcement to sup port both the machine and the workpiece.
- 1 2- H8259 1 0" x 1 8" Benchtop Lathe A ssemb ly Before use, t he tool rest must be mov ed out of its shipping position and the quill handwheel knob must be at tached. T est Ru n Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation.
H8259 1 0" x 1 8 " Benc htop L athe - 1 3 - Operati on Safety SE CTION 4 : OP ERA TIONS Lo o se hai r a nd clo th - ing could get caught in machiner y and cause seri - ous pe rsonal injury . Kee p loose clothing and long ha ir away fro m movi ng machiner y .
- 1 4 - H8259 1 0" x 1 8" Benchtop Lathe 5. Move the belt tension lever down, adjusting tension so that ½" of belt deflection is mea - sured as shown in Figure 12 , then tighten belt tension lever screw. 6. Tighten the motor mount screw.
H8259 1 0" x 1 8 " Benc htop L athe - 1 5 - The tailstock is equipped with a cam-action clamping system to secure it to the lathe bed. When the lever is tightened, a locking plate lifts and secures the tailstock to the bed. To position the tailstock along the bed: 1.
- 1 6 - H8259 1 0" x 1 8" Benchtop Lathe T o remove th e spur cente r: 1. UNPLUG LATHE FROM POWER! 2. Hold the headstock spindle wheel securely while turning the faceplate counterclockwise until the spur center is forced out of the head - stock spindle ( Figure 16 ).
H8259 1 0" x 1 8 " Benc htop L athe - 1 7 - Figure 17. Installing live center in tailstock. Quill Lock Handle Quill Handwheel Quill Remo vi n g / Insta ll in g F acepla te To remove faceplate: 1. UNPLUG LATHE FROM POWER! 2. Hold the headstock spindle wheel securely while turning the faceplate counterclockwise until it is removed.
- 1 8 - H8259 1 0" x 1 8" Benchtop Lathe • Scrapers —Mainly used where access for other tools is limited, such as hollowing oper - ations. This is a flat, double-ground tool that comes in a variety of profiles (Round Nose, Spear Point, Square Nose, etc.
H8259 1 0" x 1 8 " Benc htop L athe - 1 9 - Spindle turning ( Figure 23 ) is the operation per- formed when a workpiec e is mounted b etween the headstock and the tailstock.
-20- H 8259 1 0" x 1 8" Benchtop Lathe F aceplate turning ( Figur e 27 ) is when a workpiec e is mount ed to the faceplat e, which is moun ted to the headstock spindle. This t ype of t urning is usu - ally done with o pen-faced wo rk pieces lik e bowls.
H8259 1 0" x 1 8 " Benc htop L athe - 21 - NOTIC E : O nly use tap screws or woo d screw s with non-tapered heads ( Figure 2 8 ) to attach the faceplate to the wor kpiec e. Do NO T use drywall screw s or sc r ews with taper ed heads be cause these can s plit the facep late , or the sc r ews may snap off dur ing operation.
-22- H825 9 1 0" x 1 8" Benc ht op Lathe SE CTION 5 : A CC ESS ORI ES ACCESSORIES G1194—3-Jaw Chuck A "must ha ve " for the serious wood turner . This 3 -jaw chuc k is a self- centering st yle chuck used mostly for round work. All three jaw s tighten together at the same time .
H8259 1 0" x 1 8 " Benc htop L athe -23- SE CTION 6 : MAINT EN ANC E Alwa ys disconnect power to t he m ac hin e b efo re per forming mainte nance.
-2 4- H 8259 1 0 " x 1 8" Benc ht op Lathe T o re mo ve the old b elt : 1. Open the side and rear access covers as shown in Steps 1-5 in the Changing Speeds procedure on Page 13 . 2. Roll the belt off of the motor (lower) pulley ( Figure 36 ).
H8259 1 0" x 1 8 " Benc htop L athe -25- Revie w t he troubleshooting and procedures in this sec tion to fix or adjust y our machine if a problem devel- ops. If you need replacement parts or y ou a re unsur e of your repair skills, then feel free t o call our T echnical Suppor t at (570) 5 46 -96 63.
-26- H8 25 9 1 0" x 1 8" Benchtop Lathe Symptom Possible Cause Possible Solution Vibration noise while machine is running; noise remains constant when speed is changed. 1. Dented fan cover on motor. 1. Replace or adjust fan cover. Inspect motor fan and replace if damaged.
H8259 1 0" x 1 8 " Benc htop L athe - 27 - .
-28- H8259 1 0" x 1 8" Benchtop Lathe .
H8259 1 0" x 1 8 " Benc htop L athe -29- Mai n B reak do wn Pa r ts L i st REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH8259001 LATHE BED 32-4 PH8259032-4 CAPACITOR 24M 300V 35 X 65MM 2 PSB64M CAP SCREW M10-1.5 X 25 33 PSB14M CAP SCREW M8-1.
-3 0- H 8259 1 0 " x 1 8" Benc ht op Lathe W ar ni ng Lab el s B reak do wn & P ar ts Li st Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine.
.
.
Grizzly Industrial, Inc. wa rrants e very product it sells f or a period of 1 year to the original purchaser from the dat e of purchase. This wa rrant y does not app ly to def ects due di rec tly or indirectly t o misuse , abuse , negligence, accidents, repairs or alterations or l ack of maintenance.
.
デバイスGrizzly H8259の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Grizzly H8259をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはGrizzly H8259の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Grizzly H8259の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Grizzly H8259で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Grizzly H8259を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はGrizzly H8259の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Grizzly H8259に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちGrizzly H8259デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
