Haflerメーカー9130の使用説明書/サービス説明書
ページ先へ移動 of 20
HOME A U DIO COMPONENTS 0 W N E R S M A N U A L Series 09130 P 0 W E R A M P L I F I E R Series 9130 Power Amplifier.
NOTICE - IMPORTANT SAFETY INFORMATION Ap!!!J!A WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. 1. 2. 3. 4. 5.
11. NON-USE PERIODS During periods of extended non-use, the power cord should be unplugged from the power source. 12. CLEANING The equipment should be cleaned only as detailed in the operating instructions.
TABLE OF CONTENTS PERFORMANCE SPECIFICATIONS ............................................................................................ 4 General Information ...........................................................................................
PERFORMANCE SPECIFICATIONS GENERAL INFORMATION All specifications are for 20 Hz - 20 kHz, at full power into 8 ohms, unless specified otherwise. Power Rating: Rated THD: Full Power Bandwidth: Signal t.
INSTALLATION RACKMOUNTING VENTILATION/ PLACEMENT LINE VOLTAGE The 9130 Amplifier is supplied in either a 17” Black Version, or a 19” Silver Version. The 19” model has rackmounting holes provided for installation in equipment racks. The holes are on standard EIA spacings.
LEFT/MONO GAIN POWER SWITCH UP - ON DOWN - OFF I (3, I RACKMOUNT HOLES RIGHT (19” VERSION ONLY) GAIN 9130 AMPLIFIER FRONT PANEL VIEW.
-7-.
OUTPUTS All output connections to the amplifier must be performed with the amplifier off! GAIN CONTROLS MONO/ STEREO SWITCHING SOFT TURN- ON/OFF SYSTEM THERMAL PROTECTION SYSTEM The left and right audio outputs from the amplifier are via standard 5-way type, 3/4” spacing, binding posts.
CIRCUIT HIGHLIGHTS The 9130 employs a single ended, current source driven, differential input stage. This stage is connected to the rest of the circuitry through a balanced push-pull current mirror system. A combination current mirror and bias multiplier drive the final output stage driver emitter followers.
CHANGING LINE VOLTAGE RATING ADJUSTING BIAS The 9130 Amplifier is equipped with a simple means to adjust the AC line voltage rating for 100, 120 or 230 volts AC, 50/60 Hz.
GENERAL TROUBLESHOOTING HINTS GROUND LOOPS 4) 5) 6) 7) 8) Apply power to the amplifier, and allow the unit to thermally stabilize for about three minutes. (If using an analog meter, and the meter reads backwards, temporarily remove power and reverse the meter leads.
CLEANING/ MAINTENANCE SPECIAL NOTE ON VIDEO CABLE “GROUNDS”: As mentioned above, the ground conductor of cable service and antenna feeds should be connected to earth ground. Often, however, due to long feed lengths, especially in apartment distribution systems, this ground will be of poor quality and could be a source of noise.
LEFT/MONO INPUT LEFT/MONO (+I MONO/STEREO RIGHT INPUT LEFT - OUTPUT RIGHT - OUTPUT THERMAL - THERMAL PROTECTION I SOFT SENSORS - TURN ON/OFF SYSTEM SYSTEM A 4 9130 FUNCTIONAL BLOCK DIAGRAM.
PARTS LIST Parts values and types subject to change without prior notice. DESIGNATORS 1 -99: LEFT CHANNEL DESIGNATOR VALUE 101-l 99: RIGHT CHANNEL 201-299: COMMON PARTS 301-399: CHASSIS/POWER SUPPLY C8,C108 C9,C109 C10,C110 DESIGNATOR VALUE ALL RESISTORS 1/4 WATT, (unless specified otherwise) R1,R101 1.
a’L c4 w m IL bO I/L.
Ll u TSl n $ cl’ u 1 ‘2.5 cl’- u XI cl, 1 m I ou r”l CAUTION: d FOR CO-NliNUED PROTECTION - - u .- - AGAINST FIRE HAZARD. REPLAGE ONLY WITH SAME F4 AMP TYPE AND RATING FUSES.
JlOl RIGHT INPUT Jl LEFT INPUT 96 2N5401 1. ALL RESlSTORS IN OHMS 2. Au. CAPACITORS IN MICROFARADS 3. yxg3N~ psr..s~~oRsz lil-i99: RIGhT CHANNEL 201-298: COMMON PARTS 301-399: cHASsIs/powER SUPPLY 4. LEFT CMNNEL ONLY SHOWN 5. STEREO/MONO !MilCH SHOWN IN STEREO PCStllON 6.
Fl I l +HV SA R17 47.5 Cl1 0.1 -ca +-CQ K) 8: c, Ql.j--- I 1 “01; 5’ a12 2SK1056 l-9 ZN5550 R18 475 @ LL --e--- 4 -z- lN4148 10 R14 R13 22.1K , l.lK 1% I of3 RlOq 2N2222 SK : R26 27 % 1 1” : I R21 b 221 010 2N5401 CR8 ,I lN414.8 1 N4%? Q13 2SJl60 %.
SERVICE POLICY AND LIMITED WARRANTY If you encounter any difficulty or have any question concerning your 9130 Amplifier, please call our Customer Service Department weekdays, 8 a.
デバイスHafler 9130の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Hafler 9130をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHafler 9130の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hafler 9130の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hafler 9130で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hafler 9130を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHafler 9130の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hafler 9130に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHafler 9130デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。