Harbor Freight Toolsメーカー90692の使用説明書/サービス説明書
ページ先へ移動 of 14
LA THE DUPLICA T OR A TT A CHMENT (FOR USE WITH LA THE MODEL 90265) MODEL 90692 ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http//www .harborfreight.com Cop yr ight 2003 by Harbor F reight T ools.
PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures, parts list and as- sembl y diagram. Keep your in voice with this man ual.
SKU 90692 P A GE 3 3. Store idle equipment. When not in use, tools and equipment should be stored in a dr y location to inhibit rust. Alwa ys lock up tools and equipment, and k eep out of reach of children. 4. Do not use this product if under the influence of alcohol or drugs.
SKU 90692 P A GE 4 cannot cov er all possible conditions and situations that ma y occur . The operator must understand that common sense and caution are factors, which cannot be b uilt into this product, but must be supplied b y the operator . SPECIFIC PRODUCT W ARNINGS AND PRECA UTIONS 1.
SKU 90692 P A GE 5 ASSEMBL Y INSTR UCTIONS NOTE: For additional references to the parts listed in the following pages, refer to the Assembly Diagram on page 14 . T o Attac h The T ool Rest Base: 1. Loosen the T ool Rest Handle of the lathe , and slide the T ool Rest Base of the lathe to as near the Headstock of the lathe as possibl e.
SKU 90692 P AGE 6 3. Install one Low er V er tical Suppor t Bar (46) onto the T ool Rest Base of the lathe , and secure it by tightening the Suppor t Bar Handle of the lathe. (See Figure A.) 4. Loosen the T ailstock Handle of the lathe , and remov e the T ailstock from the Bed of the lathe .
SKU 90692 P AGE 7 U-BRACKET (38) HANDLE (3) P A TTERN SUPPORT B AR (41) P A TTERN BOL T (42) LOWER VERTICAL SUPPORT BAR (46) U-BRACKET ASSEMBL Y LOWER VERTICAL SUPPORT BAR (46) U-BRACKET ASSEMBL Y FIGURE C T o Attac h The Suppor t Bar: 1. Remove the End Cap (12) from each end of the Support Bar (54).
SQUARE NUT (47) SQUARE NUT (47) SUPPORT BAR (54) FLA T W ASHER (40) LOCKW ASHER (34) HANDLE (48) FLA T W ASHER (40) LOCKW ASHER (34) HANDLE (48) FIGURE D T o Assemb le The T ool Holder: 1. Loosen the two Set Scre ws (20) on the T ool Holder (24), and e xtend the Cutting T ool (31) out about 4 inches.
T o Attac h The T ool Holder Assemb l y: 1. Slide the Cutting T ool (31) of the T ool Holder (24) into the Slot located on the Side Plate (50). (See Figures E and F .) 2. Attach the Spring (19) over the Pointer (14) on the Side Plate (50). (See Figure F .
FIGURE G SAFETY SHIELD (8) HANDLE (51) SAFETY SHIELD PLA TE (43) SUPPORT BAR (54) BOL T P AN HEAD SCREW (9) FLA T W ASHER (21) HEX NUT (7) HEX HEAD BOL T (11) FLA T W ASHER (40) HEX NUT (39) OPERA TING INSTRUCTIONS T o Adjust The Cutting T ool: 1.
3. The Cutting T ool (31) also can be adjusted vertically by loosening the Soc ket Head Bolt (25) which secures the T ool Holder (24) in place. Once adjusted, make sure to re-tighten the Socket Head Bolt.
SKU 90692 P A GE 12 occurs, have the problem corrected before further use. Do not use damaged equipment. 2. F or better and safer perf or mance, alw ays k eep the Cutting T ool (31) clean and sharp. 3. Daily , with a clean cloth, br ush, or vacuum remo ve all debris fromthe Lathe Dupli- cator Attachment.
P AR TS LIST SKU 90692 P AGE 13 PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF A CTURER AND/OR DISTRIBUT OR HAS PRO VIDED THE P ARTS LIST AND ASSEMBL Y DIA GRAM IN THIS MANU AL AS A REFERENCE T OOL ONL Y .
NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not available individually as replacement parts. ASSEMBL Y DIA GRAM SKU 90692 P AGE 14 12 38 3 45 2 39 41 42 49 54 53.
デバイスHarbor Freight Tools 90692の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Harbor Freight Tools 90692をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHarbor Freight Tools 90692の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Harbor Freight Tools 90692の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Harbor Freight Tools 90692で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Harbor Freight Tools 90692を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHarbor Freight Tools 90692の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Harbor Freight Tools 90692に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHarbor Freight Tools 90692デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
