Hearth and Home Technologiesメーカー800の使用説明書/サービス説明書
ページ先へ移動 of 20
MODEL 800 NOV A FREEST ANDING PELLET STOVE INST ALLA TION, OPERA TION, AND MAINTENANCE INSTRUCTIONS CONGRA TULA TIONS— Yo u are now the proud owner of one of the finest stoves in the world for your home—the QUADRA- FIRE! Now before installing your stove and building your first fire, record the serial number on the warranty card.
NOTES Page 2.
T ABLE OF CONTENTS Page Safety Label ................................................................................................................... ........................................... 4 Listing and Specifications .........................
SAFETY LABEL (FOUND ON BACK W ALL OF HOPPER) Page 4.
LISTINGS AND SPECIFICA TIONS QUADRA-FIRE 800 NOV A pellet stoves are safety tested and listed with W arnock Hersey International to ASTME 1509 and ULCS627. Also suitable for mobile home installation (see page 11 for details). HEA T INPUT*: 28,000 to 37,500 BTU per hour P AR TICULA TE EMISSIONS PER HOUR: 0.
FLOOR PROTECTION MINIMUM CLEARANCES TO COMBUSTIBLE MA TERIALS The floor protector must be noncombustible material, extending beneath heater and to the front, sides, and rear as indicated below . NOTE: In a corner installation, the floor protection must follow the above clearances.
Page 7.
Page 8.
Page 9.
T OP VENT FLUE ADAPTER INST ALLA TION INSTRUCTIONS 3"-3" ADAPTER #81 1-0450 3"-6" COLLAR #812-2690 1 ) Put a layer of silicone on the 3" (76mm) exhaust outlet. 2 ) Slide the flue adapter onto the rear exhaust outlet. 3 ) Adjust the assembly to a vertical position.
MOBILE HOME INST ALLA TION OUTSIDE AIR KIT FOR 800 NOV A: P ART #81 1-0420 (FLOOR) OR P AR T #81 1-0430 (REAR) 1 An outside air inlet must be provided for the combustion air and be unrestricted while the stove is in use. 2. The stove must be secured to the mobile home by bolting it to the floor (using lag bolts).
OPERA TING INSTRUCTIONS 1. FUEL SIZE AND MA TERIAL Fuel pellets are made from sawdust or wood byproducts. If the source material is hardwood, they will have a higher mineral content, creating a heavier ash. Minerals and other noncombustible materials, such as sand, will turn into glass when heated to the extreme temperatures our firepot reaches.
Page 13.
Page 14 ( N ) COMBUSTION BLOWER ( WHITE ).
1. FIREPOT A. It takes very little time to clean the firepot. W e recommend that you clean the firepot at least once a week. However , if the fuel you are burning has a high dirt content, it will be necessary to clean the firepot more often. Dirty fuel will cause clinkers to form in the firepot.
1. POWER SUPPL Y A. Check the wall receptacle for 120 volt, 60 Hz (standard current). Make sure the outlet is grounded and has the correct polarity . 2. FUSE A. The fuse is located on the left side, next to the restart button and the indicator light. However , to access the fuse, you must remove the left side panel.
9. THERMOCOUPLE A. The thermocouple is located on top of the firepot inside the ceramic protection tube. Remove the ceramic tube and inspect the thermocouple for deterioration or breakage. B. Check the terminal block screws to see if they are tight and making a good electrical connection (located on the top of the lower junction box).
1. PLUG IN STOVE, NO RESPONSE A. Check the power supply for 120 volts AC. B. Check the fuse in the junction box (7 amp, 120 volt fuse AGC-7). C. Check snap disc #3 (unplug stove before checking). Push reset on snap disc #3. D. Control box (consult your dealer).
8. THERMOST A T WILL NOT ST ART UNIT A. Check the power to the stove. 1. Unplug for 10 seconds and then plug in. The exhaust blower should come on. If it does, go to B. B. The thermostat or the thermostat wiring maybe faulty . 1. Disconnect the thermostat wires from the terminal block located on the back of the stove.
Aladdin Hearth Products, warrants their pellet heating appliances to the original purchaser for the lifetime of the appliance, to be free from defects in material and workmanship. This warranty gives you specific legal rights; you may have other rights which may vary from state to state.
デバイスHearth and Home Technologies 800の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hearth and Home Technologies 800をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHearth and Home Technologies 800の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hearth and Home Technologies 800の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hearth and Home Technologies 800で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hearth and Home Technologies 800を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHearth and Home Technologies 800の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hearth and Home Technologies 800に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHearth and Home Technologies 800デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
