HiltiメーカーWSR900-PEの使用説明書/サービス説明書
ページ先へ移動 of 12
WSR 900 WSR 900-PE WSR 1 250-PE WSR 1 400-PE *376750* 376750 Operating instructions en Mode d’emploi fr Manual de instrucciones es Hilti Corporation FL-9494 Schaan T el.: +423 / 234 21 1 1 Fax: +423 / 234 29 65 www .hilti.com Hilti = registered trademark of Hilti Corp.
W S R 9 0 0 - P E min.40mm 1– 6 2 3 W S R 12 5 0 - P E W S R 1 4 0 0 - P E V V V V V 2 4 5 6 7 min.40mm 3 min.40mm min.25mm W S R 9 0 0 - P E B A W S R 1 25 0 - P E W S R 1 4 0 0 - P E W S R 1 4 0 0.
1 en It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions together with the tool. Ensure that the operating instructions are with the tool when it is given to other persons.
2 en 2. General safety rules 1. WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury . SA VE THESE INSTRUCTIONS 2. Wo rk Area Keep your work area clean and well lit.
3 en 3. Specific safety rules and symbols 3.1 Basic information concerning safety In addition to the information relevant to safety given in each of the sections of these operating instructions, the following points must be strictly observed at all times.
4 en 3.3.2 Electrical ● Protect yourself against electric shock. Avoid body contact with earthed / grounded objects, e.g. pipes and radiators etc. ● Check the condition of the tool’ s supply cord at reg- ular intervals. The supply cord should be replaced by a trained electrical specialist if damage is found.
5 en 4. Functional description 4.1 Use of the WSR 900 / WSR 900-PE as directed ● T ypical working environments include rescue ser vices, public authorities, farming and forestry , general con- struc.
6 en 5. Assembly -NOTE- The electric supply voltage must comply with the infor- mation on the type plate. If extension cords are used: Use only extension cords of a type approved for the intended purpose and of ade- quate cross section. Failure to observe this point may result in reduced performance and may cause the cord to overheat.
7 en 6. Operation -NOTE- ● To ensure good cutting performance and ease the load on the tool, use only saw blades that are in good con- dition. ● Do not overload the tool. -WARNING- ● When working, always guide the tool away from the body . ● Lift the tool away from the workpiece only once the blade has come to a standstill.
8 en 7. Care and maintenance Unplug the supply cord from the mains socket. 7.1 Care of blades Clean off dirt and dust deposits and protect your blades from corrosion by wiping them from time to time with an oil-soaked rag. 7.2 Care of the tool ● Keep the blade clamp clean.
9 en 10. Disposal Most of the materials from which Hilti electric tools are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old electric tools for recycling.
10 en 11. Warranty Hilti warrants that the tool supplied is free of defects in material and workmanship. This warranty is valid so long as the tool is operated and handled correctly , cleaned and serv.
デバイスHilti WSR900-PEの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hilti WSR900-PEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHilti WSR900-PEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hilti WSR900-PEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hilti WSR900-PEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hilti WSR900-PEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHilti WSR900-PEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hilti WSR900-PEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHilti WSR900-PEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
