HoneywellメーカーCT8775Aの使用説明書/サービス説明書
ページ先へ移動 of 20
OWNER’S GUIDE ® U.S. Registered T rademark • Patent s Pending Copyright © 2004 Honeywell Internat ional Inc. All Rights Reserved 69-1676—1 CT8775A,C THE DIGITAL ROUND ™ NON-PROGRAMMABLE THER.
69-1676—1 2 Enjoy the benefits of The Digit al Round TM Thermostat by Honeywell. • Simple to use. T urn the dial to adjust the temper ature setting. • Large easy-to-read display . The temperature reading is easily seen from a distance. • Backlit display .
3 69-1676—1 STEP 1. PREPARE FOR INSTALLATION ❑ Check T able 1, the compatibility chart, to make sure t he t hermostat is compatible with your system. If your system is not compatible, call Honeywell Customer Care, toll-free, 1-800-468-1502. T able 1.
69-1676—1 4 STEP 2. REMOVE OLD THERMOSTAT ❑ T est your heating and cooling systems to make sure they work properly . If either system does not wor k, contact your local heating/air-conditioning dealer . T o avoid compressor damage, do not o perate the cooling system when outdoor temperature is below 50°F (10°C).
5 69-1676—1 Replacing a thermostat that is connected to three wires on a warm air heating only system If you are replacing a thermostat that is connected to thr ee wires on a warm air heating only system and could turn the fan on by setting the thermostat fan switch to ON, the CT8775C Thermostat will work with your system.
69-1676—1 6 Mount Decorator Cover Pl ate (Optional) and Wall plate Directly to Wall ❑ If using the decorator cover plate, pull the wires through the wiring hole on the decorator co ver plate. Position the decorator cover plate against the wall so that the UP indicator in the middle of the decorator cover plate is pointing up.
7 69-1676—1 . Mount Decorator Cover Plat e (Required) and Wallpl ate onto Electrical Box ❑ Pull the wires through the wiring hole on the decorator cover plate. ❑ Place the decorator cover pl ate against the electrical box so that the UP indicator in the middle of the decorator cover plate is pointing up.
69-1676—1 8 STEP 7. WIRE WALLPLATE TERMINALS IMPORTANT All wiring must comply with local codes and ordinances. If unsure about household wiring pr ocedures, call your local heating/air conditioning contractor. ❑ Refer to the labels you placed on the wires wh en you removed the old thermostat (see illustration).
9 69-1676—1 T able 2. T erminal Designatio ns on Old and New Thermostats. NOTES: 1. If wires were connected to both Rh and R terminals on the old thermostat, remove jumper betwe en R and Rc on the new thermostat and connect Rh to R and R to Rc. 2. If wires will be connected to both R and Rc on the new thermostat, remove jumper between R and Rc.
69-1676—1 10 STEP 8. CUSTOMIZE THE THERMOSTAT Set Fuel Switch (CT8775C Only) ❑ T o adjust the fuel sw itch, locate the switch labeled E/F on the wallplate (see Fig. 3). The fuel switch is factory set in the F position. This is the correct setting for gas or oil syste ms.
1 1 69-1676—1 T able 3. Heat Cycle R ate. NOTE: The cooling cycle rate does not requi re adjustment and therefore cannot be changed. Fahrenheit/Celsius Indication ❑ Use DIP switch 3 to set the desired temperature indication. See T able 4. T able 4.
69-1676—1 12 STEP 10. SET THE SYSTEM AND F AN SWITCHES (CT8775C ONLY) System Switch (see Fig. 5) ❑ Heat: The thermostat controls your heating system. ❑ Off: Both the heating and cooling systems are off. ❑ Cool: The thermostat controls your cooling system.
13 69-1676—1 STEP 11. OPERATING THE THERMOSTAT NOTE: Batteries are not required because the tem peratu re setting is held permanently in memory . Backlit Display ❑ The backlight can be turned on by turning the di al, or pushing the backlight button (see Fig.
69-1676—1 14 Cooling System (CT8775C Only) CAUTION Equipment Damage Hazard . Can cause permane nt damage to compressor o r other equipment. Do not operate cooling when outsid e temperature is below 50°F (10°C). Allow compressor to remain off for five minutes before restarting.
15 69-1676—1 IF YOU HAVE A PROBLEM T able 5. Solution Guid e. Customer Assistance Please read and follow the provided instructions for this the rmostat. For additional information, go to www .honeywell.com/yo urhome or call Honeywell Customer Care, toll free, at 1-800-468-1502.
69-1676—1 16 Wiring Diagrams POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED. W R HEATING RELAY OR VALVE COIL M19450 1 1 M19451 HEATING RELAY OR VALVE COIL FAN RELAY 1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.
17 69-1676—1 Notice: This thermostat is a Class B digita l app aratus that complies with C anadian R adio Interference Regulations, CRC c. 1374. 1 4 COMPRESSOR CONTACTOR HEAT CHANGEOVER VALVE COOL CHANGEOVER VALVE FAN RELAY M19453 1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.
69-1676—1 18 Limited One-Year Warranty Honeywell warrants th is product to be free from defects in the workmanship o r materials, under normal use an d service, for a pe riod of one (1) year from the date of purcha se by the consumer .
19 69-1676—1.
69-1676—1 J.S. Rev . 6-04 www .honeywell.com/yourhome Automation and Control Solutio ns Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Go.
デバイスHoneywell CT8775Aの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Honeywell CT8775Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHoneywell CT8775Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Honeywell CT8775Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Honeywell CT8775Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Honeywell CT8775Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHoneywell CT8775Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Honeywell CT8775Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHoneywell CT8775Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。