HP (Hewlett-Packard)メーカー410Cの使用説明書/サービス説明書
ページ先へ移動 of 63
TM 11-6625-1614-15 DEPARTMENT OF THE ARMY TECHNICAL MANUA L ORGANIZATIONAL, DS, GS, AND DEPOT MAINTENANCE MANUAL HEWLETT-PACKARD ELECTRONIC VOLTMETER MODEL 410C This copy IS a reprint which includes curren t pages from Change 1 .
TM 11-6625-1614-15 WARNING DANGEROUS VOLTAGES EXIST IN THIS EQUIPMENT Be careful when working on the power supplies and their circuits, or on the 115- or 230-vol t ac line connections .
This manual contains copyrighted material prepared by the Hewlett-Packard Co. TM 11-6625-1614-15 TECHNICAL MANUAL HEADQUARTERS DEPARTMENT OF THE ARMY No.
TM 11-6625-1614-15 Section Number 1-1. 3-1. 5-1. 5-2. 5-3. 5-4. 5-5. 5-6. 5-7. 5-8. 5-9. 5-10. Number 1-1. 2-1. 2-2. 2-3. 2-4. 3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8. 4-1. 4-2. 4-3. 5-7 . 5-9 . 5-10 . 5-13 . 5-16 . 5-17 . 5-21 . 5-22 . 5-26 . 5-28 . 5-29 .
TM 11-6625-1614-15 Number 4-4. 4-5. 4-6. 5-1. 5-2. 5-3. 5-4. 5-5. 5-6. 5-6.1 5-7. 5-8. 5-9. 5-10. 5-11. 5-12. 5-13. 5-14. Simplified Schematic, DC Voltage Measurements --------------------------------.
Figure 1-1. TM 11-6625-1614-15 Model 410 C Section I Figure 1-1 1- 0.
TM 11-6625-1614-15 SECTION I GENERAL INFORMATION 1-A.1. Scope a. This manual includes installation and operation instructions and covers operator’s, organizational, direct support (DS), general support (GS), and depot maintenance. It describes Hewlett-Packard (Federal supply code 28480) Electronic Voltmeter Model 410C.
.
Table 1-1. TM 11-6625-1614-15 Section I Table 1-1 Model 410C 01556-2 1-3.
TM 11-6625-1614-15 Model 410C 1-1. DESCRIPTION. 1-2. The Hewlett-Packard Model 4l0C Electronic Voltmeter can be used to measure DC voltage and DC current; AC voltage and resistance. Positive and negative DC voltages from 10 millivolts to 1500 volts and positive and negative DC currents from 1.
Model 410C TM 11-6625-1614-15 1-4. ACCESORIES AVAILABLE . 1-5. MODEL 11036A AC PROBE. This accessory, when used with the Model 410C, permits AC voltage measurements from 0.5 volt rms to 300 volts rms, full scale over a frequency range of 20 cps to 700 Mc.
Model 410C TM 11-6625-1614-15 Section II Figures 2-l and 2-2 Figure 2-1. The Combining Case Figure 2-2. Steps to Place Instrument in Combining Case 2-0 01556-1.
TM 11-6625-1614-15 Model 410C Section II Paragraphs 2-1 to 2-13 SECTION II INSTALLATION . 2-1. INSPECTION. 2-2. ‘This instrument was carefully inspected both mechanically and electrically, before shipment. It should be physically free of mars or scratches and in perfect electrical order upon receipt.
TM 11-6625-1614-15 Section II Paragraph 2-14 to 2-15 DO NOT CHANGE THE SETTING OF THE LINE VOLTAGE SWITCH WHEN THE VOLT- METER IS OPERATING. 2-14. REPACKAGING FOR SHIPMENT. 2-15. The following paragraphs contain a general guide for repackaging of the instrument for shipment.
TM 11-6625-1614-15 Model 410C Section III Paragraph 3-1 to 3-18 SECTION III OPERATION . 3-1. INTRODUCTION. 3-2. The Model 410C is used to measure AC and DC voltage, DC current, and resistance. All measure- ment inputs are located on the front panel; a DC out- put connector is located on the rear panel.
TM 11-6625-1614-15 Section III Model 410C Figure 3-1 1. 2. 3. 4. 5. 6. 7. FUNCTION SELECTOR: This control is used for selecting type of measurement to be made. They are: ±DC Voltage, ±DC Current, AC Voltage, and resistance measurements. AC ZERO: This control provides adjustment for zero-setting the meter before making AC volt- age measurements.
Model 410C TM 11-6625-1614-15 Section III Paragraphs 3-19 to 3-27 and Table 3-1 second maY be made without loss of accuracy by re- moving the. plastic nose on the Model 11036A and using in its place a 0.25 microfarad blocking capacitor in series with the exposed contact of the probe.
TM 11-6625-1614-15 Section III Paragraphs 3-28 to 3-34 PRF is the pulse repetition frequency in pulses per second (pps). Suppose, for example: t 1 = t 2 = K = PRF = 10 microseconds 990 microseconds 0.55 1000 pps To find K, assuming / = 2 kilohms and t l=10micro- seconds: R o / t l = 2 10° = 0.
TM 11-6625-1614-15 Model 410C Section III Figure 3- 2 01556-2 Figure 3-2. DC Voltage Measurements 3-5.
TM 11-6625-1614-15 Section III Model 410C Figure 3-3 Figure 3-3. DC Current Measurements 3-6 01556-3.
TM 11-6625-1614-15 Model 410C Section III Model 410C Figure 3-4. AC Voltage Measurements 01556-3 3-7.
Figure 3-5. TM 11-6625-1614-15 Section III Figure 3-5 Model 410C 3-8 01556- 2.
TM 11-6625-1614-15 Model 410C Section III Figure 3-6 Figure 3-6. Graph Used in Calculation of Pulse Voltage Readings 01556-2 3-9.
TM 11-6625-1614-15 Section III Model 410C Figure 3-7 Figure 3-7. Resistance Measurements 3-10 01556-2.
TM 11-6625-1614-15 Model 410C Section III Figure 3-8 Figure 3-8. DC Nano-Amoere Current Measurements 01556-3 3-11.
TM 11-6625-1614-15 Section IV Figure 4-1 and 4-2 Model 410C Figure 4-1. Block Diagram, Model 410C Figure 4-2. Modulator-Demodulator Mechanical Analogy 4-0 01556-2.
TM 11-6625-1614-15 Model 410C Section IV Paragraph 4-1 to 4-18 4-1. 4-2. OVERALL DESCRIPTION. The Model 410C includes SECTION IV THEORY OF OPERATION an input network, a modulator - amplifier- demodulator, and a meter circuit. A block diagram of the Model 410C is shown in Figure 4-1.
TM 11-6625-1614-15 Section IV Paragraphs 4-19 to 4-31 Model 410C voltage or current being measured) to the neon-photo- conductor chopper. Also applied to the opposite side of the chopper is the amplifier feedback voltage, which is of the same polarity and approximately 5 micro- volts lower in amplitude than the input voltage.
Figure 4-3. Model 410C TM 11-6625-1614-15 Section IV Figure 4-3 01556-2 4-3.
Figure 4-4. TM 11-6625-1614-15 Section IV Figure 4-4 Model 410C 4-4 01556-2.
Figure 4-5. TM 11-6625-1614-15 Section IV Figure 4-5 01556-2 4-5.
Figure 4-6. TM 11-6625-1614-15 Section IV Figure 4-6 Model 410C 4- 6 01556-2.
.
TM 11-6625-1614-15 Section V Model 410C Table 5-1 Table 5-1. Recommended Test Equipment Instrument Type Required Characteristics Use Recommended Model Voltmeter Calibrator Range: .015 to 300 v AC and DC Accuracy @ Model 738BR Volt- Frequency: DC and 400 cps Checks and Calibration meter Calibrator Accuracy: +0.
TM 11-6625-1614-15 Model 410C Section V Paragraphs 5-1 to 5-11 5-1. INTRODUCTION . SECTION V MAINTENANCE 5-2. This section contains maintenance procedures for the Model 410C Electronic Voltmeter. 5-3. TEST EQUIPMENT REQUIRED. 5-4. The test equipment required to maintain and adjust the Model 410C is listed in Table 5-1.
TM 11-6625-1614-15 Section V Paragraphs 5-12 to 5-15 Table 5-2 Model 410C Table 5-2. DCV Accuracy Test Model 410C Range Settings .015V .05 V .15 V .5 V 1.5 V 5 V 15 V 50 V 150V 500 V 1500 5-12 Voltmeter Calibrator Model 738B Settings Range 1. 5-5 1. 5-5 1.
TM 11-6625-1614-15 Model 410C Section V Tables 5-3 and 5-4 Figure 5-2 Figure 5-2. DC Ammeter Operation Table 5-3. DCV Input Resistance Test Table 5-4. DCA Accuracy Test 01556-2 5-3.
TM 11-6625-1614-15 Section V Paragraphs 5-16 to 5-19 Table 5-5 Model 410C g . 5-16. c. Adjust dc power supply to provide system voltmeter reading of 1.50 v. e. Model 410C should read approximately 150 ma. This will verify a R in of approxi - mately 0.
TM 11-6625-1614-15 . Model 410C Section V Parsgraphs 5-20 to 5-23 Figure 5-3 Figure 5-3. High Frequency Response Test c. Set Model 410C FUNCTION SELECTOR to +DCV ; RANGE to .015 V. d. Adjust voltmeter calibrator for +. 015 VDC output. e. The dc voltmeter should read +1.
TM 11-6625-1614-15 Section V Model 410C Parsgraphs 5-24 to 5-25 Figure 5-4, Table 5-6 Figure 5-4. Low Frequency Response Test AC VOLTMETER ACCURACY CHECK. a. A Voltmeter Calibrator Model 738BR) will be required for this operation. b. Adjust voltmeter calibrator for 400 cps- rms output.
Model 410C TM 11-6625-1614-15 b . Connect the Model 410C as shown in Figure 5-4. Set Mode l 410C FUNCTION SELECTOR toACV; RANGE to 1.5 V. c . Set frequency response test set to EXTERNAL . d . Adjust test oscillator output AMPLITUDE to provide Mode l 410C reading of 1.
TM 11-6625-1614-15 Model 410C k. Vary RF signal generator frequency from 10 Mc to 480 Mc . Model 410C should read between 0.40 to 0.50 v at all frequencies . l . If power meter pointer varies from reference determined i n step j above, readjust RF signal generator OUTPUT LEVEL to retur n pointer to reference deflection .
TM 11-6625-1614-15 b. Use ac voltmeter to verify Model 410C lin e f. Observe counter, and adjust A3R5 for a chop- voltage of 115 v. Chopper frequency will vary with per frequency of 100 cps ( ±2 cps). line voltage variations. c. Connect 410C, electronic counter, an d 5-29.
.
Model 410C TM 11-6625-1614-15 b . Adjust DC Standard (H-P Model 740A) to apply .015 to Mode l 410C . c . Model 410C should read full scale . If not, adjust A6R1 8 for proper pointer deflection . d . Reset Model 410C RANGE to 1500 v. Adjust dc standard fo r 1000 v output .
TM 11-6625-1614-15 Model 410C b . Short OHMS and COM cables. Model 410C should read zero . c . Vary Model 410C RANGE switch through remainder of OHMS settings . Meter should read zero, except at RX10 when mete r should read about 0.1 ohm (resistance of leads) .
Table 5-8. Model 410 C TM 11-6625-1614-15 5-1 3.
TM 11-6625-1614-15 Model 410C Section V Paragraphs 5-38 to 5-46 instrument circuitry in an effort to localize the pro- blem. These operations should be undertaken only after it has been established that the difficulty can not be eliminated by the Adjustment and Calibration Pro- cedures, Paragraph 5-26.
Section V paragraphs 5-47 to 5-48 Figure 5-6 boards. Use caution when removing them to avoid damaging mounted components. The Part Number for the assembly is silk screened on the interior of the circuit board to identify it. Refer to Section VI for parts replacement and Part Number information 5-47.
Table 5-9. Paragraph 5-34 Table 5-10 TM 11-6625-1614-15 Model 410C Section V Table 5-9 01566-2 5-1 6.
Figure 5-7. Table 5-10. Paragraph 5-29 Figure 5-10 Figure 5-7 Table 5-9 Figure 5-10 Figure 5-10 Table 5-9 TM 11-6625-1614-15 Section V Model 410C Table 5-10 5-1 7.
TM 11-6625-1614-15 Model 410C Figure 5-11. Model 11036A AC Probe (Exploded View) 5-22 Figure 5-12. Model 11036A AC Probe Schematic 01556-2.
Figure 5-6.1. TM 11-6626-1614-15 Change 1 5-16.1.
.
TM 11-6625-1614-15 Section V Figure 5-8 Figure 5-8. Power Supply Schematic 5-19.
5-20 TM 11-6625-1614-15 Figure 5-9. Typical Amplifier Waveforms.
.
.
.
By Order of the secretary of the Army: Official : KENNETH G. WICKHAM, Major General, United States Army, The Adjutant General. Distribution: Active Army; USAMB (1) USACDCEC (.1) USACDCCEA (1) USA CDCCEA Ft Huachuca (1) NG: None. USAR: None. For explanation of abbreviations used, see AR 320-50.
.
THE METRIC SYSTEM AND EQUIVALENTS.
PIN: 016288-00 0.
デバイスHP (Hewlett-Packard) 410Cの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
HP (Hewlett-Packard) 410Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHP (Hewlett-Packard) 410Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。HP (Hewlett-Packard) 410Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。HP (Hewlett-Packard) 410Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
HP (Hewlett-Packard) 410Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHP (Hewlett-Packard) 410Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、HP (Hewlett-Packard) 410Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHP (Hewlett-Packard) 410Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
