HPメーカーLASERJET 3600の使用説明書/サービス説明書
ページ先へ移動 of 23
HP LaserJet 3000, 3600 and 3800 Series Printers - Part Numbers Not Found in the Service Manual Introduction The following part numbers are not in the Service Manual.
Product # Product Name Service Note Number for Reimbursement Q7533A HP Color LaserJet 3000 Q7533A - C00775200 Q7534A HP Color LaserJet 3000n Q7534A - C00775200 Q7535A HP Color LaserJet 3000dn Q7535A -.
Product Number Starting Serial Number Ending Serial Number Q7534A CNAFA00000 CNXFN03331 Q7535A CNAGA00000 CNXGR00812 Q7536A CNAGA00000 CNXGS02350 Q5981A CNAA00000 CNWKF09263 Q5981A CNKAA00000 CNXKF033.
6. Remove the interlock switch assembly by r emoving the one screw attaching it to the chassis. Be aware of the clip at the top and the alignment knob when removing the assembly. 7. Remove the bottom cable harness. There is one scre w at the top to remove.
8. Remove the main drive assembly (MDA). There are six screws attaching the MDA to the chassis. Carefully note the locations of the screws to be removed.
Remove the metal case by removing two screws. Remove the White L ink Arm (see arrow in figure below).
9. Remove the white slide lever by pushing down from the top to release it from the two tabs. Carefully remove the lever by pulling out, be aware that four springs are attached to this lever and the individual cartridge locks. 10. Once the sliding lever is removed, the cartridge locks can be accessed.
11. To attach the cartridge lock, hook the square part of the grounding spring to the metal chassis, then pull down and attach the lock on the metal shaft. NOTE: Replace all four cartridge locks, even though the others may not be broken. If one lock experienced failure, the others are more prone for failure later.
13. The slide lever and cartridge locks should look like the picture below when all is in pl ace. 14. Lock the white slide lever in place by installing the metal case and white plastic piece . Make sure to insert the flange of the sheet metal in the slot on the sheet metal, and place the white shaft in the while slide lever.
15. Connect the four springs on the white slide lever to each of the individual cartridge locks (start from the middle ones, it is easier that way). You will need needle-nosed pliers with pointed tips. The spring on the top is attached; the one on the bottom is not attached.
NOTE: If this procedure has been properly followed, in the back of the printer, you will see the 4 white cams that control the movement of developers (see figure below). On the top and bottom shafts, you can see a black plastic part that has a flag associated with it.
17. Prepare the MDA for installation. Two areas must be checked: a. Make sure that all the white shafts are pushed to the right (clockwise) when the MDA is oriented as shown below (See the blue arrows in the image below.). The shafts are aligned correctly in the picture.
b. Next, pay attention to the area marked with the two red arrows, enlarged in the picture below. It is possible that during the handling of the MDA one or both of these two gears can be mis-positioned by accident. If this happens, one or more of the color planes could be missed during printing.
holes from larger gears should both be showing as illustrated by the red circles . (The large gears are under the frame and driven by the smaller gears.) 18. With the above in alignment, install the main drive assem bly. Start at the left side, inserting the MDA into the metal slots and rotate it into position.
20. At this point, reverse steps 7 on down. This will have the printer back up and running. Remember to correctly thread the cables through the wire harnesses properly! NOTE: The connector to the top cov er is different between the sim plex and duplex models.
AISS Main Drive Ass'y (MDA) rework possible side-effects Possible Failures After Rewo rk Troubleshooting • 54.XX Error 59.C0 Error One of the two drive gears on the engine is NOT correctly inserted.
Figure 2: Troubleshooting lock position Figure 3: Troubleshooting gear alignment Noise - Check the Main Drive Assembly to see that the cartridge drum sensor is correctly seated. See the picture below for the proper orientation of t he sensor. There are 4 of these (one per drum) on the MDA.
Figure 4: Troubleshooting cartridge drum sensor Recommended Action: Fix on Specified Failure Objective: Recommended Modification LABOR ALLOWED Hours: 1 Minutes: 0 Service Delivery Type: Customer Site .
HP Color LaserJet 3000, 3600, and 3800 Series Printers - Broken Cartridge Lock Emerging Issue Issue Description Troubleshooting Issue Description Customers may experience a 10.92.XX error or cannot seat their cartridges properly. If the part circled below is broken, the printer must be replaced.
guides down and the levers will go be in the correct position to insert cartridges. The white piece will be down and black locking levers will be up to allow easy insertion of t he cartridge. Also check if the contact spring is being caught by the side frame sheet metal when the front door is being opened.
To help Division understand the issue better, when you have such a case, please gather this information: • Model number and serial number • Which Cartridge lock is broken (Black, Yellow, Cyan or M.
Was the ETB in the ?up? position (see picture) when the door opened? Please capture any other customer comments with respect to the discovery tape. • When did this occur? (Select 1) o Right out of box? (the first time the customer removed the toner cartridge, could they get it out, or put it in?) Describe the customer?s comments.
• Is the printer sitting on a level surface? • See the Service Action Advisory (Service Note) titled "HP Color Laser Jet 3000, 360 0 and 3800 Printers - Cartridge Lock Replacement Procedure", knowledgebase document number c00775200 .
デバイスHP LASERJET 3600の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
HP LASERJET 3600をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHP LASERJET 3600の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。HP LASERJET 3600の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。HP LASERJET 3600で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
HP LASERJET 3600を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHP LASERJET 3600の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、HP LASERJET 3600に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHP LASERJET 3600デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。