Hunter Fanメーカー40120の使用説明書/サービス説明書
ページ先へ移動 of 28
1 Electronic/Mechanical Thermostat Model 40120 installation and operation manual 44018-01 04-01-2008.
2 For assistance with wiring or operation, our T echnical Support Group is available from 8 am to 5 pm CST . they may be reached toll-free at 1-888-830-1326.
3 T able of Contents Important Information ....................................... 5 T ools ................................................................. 6 Uninstalling the Existing Unit ............................ 9 Installing the Thermostat ...
4 Congratulations! Thank you for choosing a Hunter thermostat. Y our new Hunter thermostat will provide years of reliable service and year-round energy savings. Please read this manual before beginning installation and save this booklet for complete operation instructions.
5 This thermostat is designed to work on the following heating and cooling systems: Gas – Standing Pilot Gas – Electronic Ignition Gas – Fired Boilers Gas – Millivolt Systems Oil – Fired Boilers Oil – Fired Furnace Electric Furnace This thermostat is not designed for heat pump systems or 1 10/220 V baseboard heating systems.
6 This thermostat includes two #8 slotted screws and two wall anchors for mounting. T o install your new thermostat, you will need the following supplies: Flat-head screwdriver ..........................................................................
7 NOTICE! Do not disconnect the wires from the existing thermostat before reading these instructions. The wires must be labeled prior to removal to ensure proper reconnection.
8 Y RC G W Y RC G W.
9 1. T urn the system power OFF from the existing thermostat. T urn the power to the HV AC system OFF at the main power panel or at the furnace. 2. Remove the existing thermostat cover to access the wires from the wall. (Some thermostats may have multiple covers, screws or other locking devices that must be removed or disengaged.
10 If your existing thermostat is marked... label the wire with this sticker: RH / R / VR / 4 RH RH 24 V olt W / H W W heating G / F G G fan * See page 27 for complete wiring diagram.
11 4. Using the provided stickers, label each wire according to the chart. (If the terminals are not labeled, contact a qualied HV AC technician.) Note: Wire colors do not always comply with standards, so wire color should be ignored. Refer to the existing terminal designation for proper identication.
12 INST ALLING THE THERMOST A T INST ALLING THE THERMOST A T 1. Remove the new thermostat from the back plate by pulling the two halves apart. Thermostat W all Plate.
13 W RH G.
14 2. Position the new wall plate on the wall and pull the labeled wires through the opening. 3. If the existing holes do not match those on the Hunter wall plate, or if there are no existing holes, level the wall plate and mark the wall for two holes.
15 RH G W.
16 INST ALLING THE THERMOST A T , CONT . CONNECTING THE WIRES 1. Loosen, but do not remove, the terminal screws. 2. Match and connect the wires from the wall to the terminals as shown. Wires should be inserted behind the black terminal shields. T ighten each screw after the connection has been made.
17 HE/HG Switch HG HE.
18 A TT ACHING THE THERMOST A T 4. Locate the HE/HG s w i t c H on the back of the thermostat. Set the switch to HG for a gas furnace or oil burner . Set the switch to HE for electric furnaces. 5. Insert two fresh AA alkaline batteries. 6. Align the thermostat with the the wall plate, and snap the two halves together .
19.
20 Fan Switch System Switch Set T emperature Slider Thermometer Battery Indicator SY STEM OFF HE A T AU T O ON 3 0 2 0 1 0 9 0 8 0 7 0 6 0 5 0 F C 9 0 8 0 7 0 6 0 5 0 F.
21 OPERA TION 1. Set the s E t t E m p E r a t u r E s l i d E r to the desired temperature. 2. The s y s t E m s w i t c H determines the operating mode of the thermostat. Select O f f or H E a t . 3. The f a n s w i t c H should normally be located in the a u t O position.
22 INDICA T ORS AND ADUSTMENT 1. The t H E r m O m E t E r indicates the room temperature. 2. The B a t t E r y i n d i c a t O r displays two stages of w E a k B a t t E r y w a r n i n G , indicated by the B a t t E r y i n d i c a t O r ashing once approximately every second.
23 Span Adjust SP AN.
24 INDICA T ORS AND ADJUSTMENTS, CONT . 1. Remove the thermostat from the wall plate. 2. T o make your system run LONGER, turn the s p a n a d j u s t clockwise. 3. T o make your system run SHORTER, turn the s p a n a d j u s t counter clockwise. 4. Reattach the thermostat to the wall plate.
25 1. My heating or cooling will not turn on or off. 1 a. Check the HE/HG switch to ensure it is set to the correct position. 1 b. Check the circuit breakers and switches to ensure there is enough power to the system. 1 c. Replace the batteries with fresh AA alkaline batteries.
26 Is there help on the web? Y es. Visit http://www .hunterfan.com for more information. .................................................................................... ......... Can’t I just call someone? Sure. Our T echnical Support Group is available from 8 am to 5 pm CST .
27 WIRING DIAGRAMS Rh W Heat 24V or Millivolt Supply Heat Rela y or V alve 2-wire Heat Only System G Rh W Heat 24V Supply Heat Rela y or V alve 3-wire Heat Only System Fan Relay.
28 © 2007 Hunter Fan Company.
デバイスHunter Fan 40120の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hunter Fan 40120をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHunter Fan 40120の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hunter Fan 40120の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hunter Fan 40120で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hunter Fan 40120を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHunter Fan 40120の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hunter Fan 40120に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHunter Fan 40120デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
