Husqvarnaメーカーk2500の使用説明書/サービス説明書
ページ先へ移動 of 16
E E E E n n n n g g g g l l l l i i i i s s s s h h h h K2500 Oper ator ′ s manual Please r ead the operator’ s manual carefull y and make sur e you understand the instructions before using the machine.
2 – English KEY T O SYMBOLS K ey to symbols W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or f atal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
English – 3 CONTENTS Contents KEY T O SYMBOLS K ey to symbols ............................................................. 2 CONTENTS Contents ...................................................................... 3 WHA T IS WHA T? What is what on the po wer cutter? .
4 – English WHA T IS WHA T? What is what on the po wer cutter? 16 17 1 Cutting blade 2 Guard f or the blade 3 Catch f or the guard 4 F ront handle 5 W ater tap 6 Rating plate 7 Switch lock 8 W ater .
English – 5 SAFETY INSTR UCTIONS Steps bef ore using a new po wer cutter . • This machine is a h ydraulically operated po wer cutter intended f or free-hand cutting. The machine should be connected to a h ydraulic unit with an oil flow of 35-42 litres/min and a maximum pressure of 150 bar .
6 – English SAFETY INSTR UCTIONS Switc h lock The s witch lock is designed to pre vent accidental operation of the s witch. When the loc k (A) is pressed in this releases the s witch (B). The s witch lock remains pressed as long as the s witch is pressed.
English – 7 SAFETY INSTR UCTIONS • W ear personal protective equipment. See instr uctions under the heading P ersonal protective equipment. • Ne ver use a machine that has been modified in an y wa y from its original specification. • Ne ver use a machine that is f aulty .
8 – English SAFETY INSTR UCTIONS • Suppor t the work piece in such a wa y that it is possible to predict what will happen, and so that the cut remains open while cutting. • Check that the b lade is not in contact with anything when the machine is star ted • Alwa ys cut at maximum speed.
English – 9 SAFETY INSTR UCTIONS • Stand at a comf or table distance from the work piece. • T ak e care when inser ting the blade in an e xisting cut. • Ne ver cut abo ve shoulder height. • Be aler t to mov ement of the work piece or anything else that can occur , which could cause the cut to close and pinch the blade .
10 – English SAFETY INSTR UCTIONS Check that the b lade is approv ed for the same or higher speed according to the aprov al plate of the engine. Nev er use a cutting blade with a lo wer speed rating than that of the power cutter . Ensure the blade it not cr ack ed or damaged in any other w ay .
English – 11 ASSEMBL Y Assemb ly Fitting the cutting blade Husqvarna’ s blades are approv ed f or hand-held power cutters. Blades are manufactured with three diff erent diameters of centre holes: 20 mm (0.787"), 22.2 mm (7/8") and 25.4 mm (1").
12 – English ST AR TING AND ST OPPING Starting and stopping Starting • Grip the front handle with the left hand. • Grip the rear handle with the r ight hand. When you g rip the rear handle this releases the s witch lock. Stopping The machine is stopped by releasing the s witch.
English – 13 MAINTENANCE Maintenance T ensioning the drive belt The drive belt is fully enclosed and well protected from dust and dir t. When the drive belt is to be tensioned, release the nuts holding the cutting arm. Screw the adjuster scre w so that the square headed nut comes opposite the marking on the cover .
14 – English MAINTENANCE ´®z+R=@¶6r¨ ´®z+R=@¶6r¨ Daily maintenance Carr y out the f ollowing chec ks daily bef ore using the machine. 1 Check that n uts and screws are tight. 2 Check that the po wer source (the h ydraulic unit) supplies the correct oil flow and oil pressure .
English – 15 TECHNICAL D A T A T echnical data Note 1: Handle vibrations are measured according to ISO 8662-4 Cutting equipment EC-dec laration of conformity (Applies to Eur ope only) Husqv arna Con.
´®z+R=@¶6r¨ 2006-12-20 ´®z+R=@¶6r¨ 1150293-26.
デバイスHusqvarna k2500の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Husqvarna k2500をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna k2500の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna k2500の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna k2500で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna k2500を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna k2500の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna k2500に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna k2500デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。