Ice-O-MaticメーカーCD300の使用説明書/サービス説明書
ページ先へ移動 of 21
Service/Installation Manual Hotel Dispenser Model - CD300 Mile High Equipment 1 1 100 East 45th A ve Denver , Colorado 80239 Part Number 9081292-01 Print Date 04/02.
Introduction CD300 Page 1 To the ow ner or user: This product manu al is a s ource of inform ation about th e installation, start up, clea ning, maint enance an d repair of the product.
Specificatio ns CD300 Page 2 Specificati ons and Limitations This dispenser is designed to dispense cubed ice only and to be installed and operated indoors, in a controlled enviroment. Its minimum and maximum operating temperature limits are the same as those for the ice machine.
Diagrams CD300 Page 3.
Uncratin g CD300 Page 4 Remove th e carton from the skid. C ut the plastic stra ps that secure the leg kit to the ski d and rem o ve t he bo x. Use the di spenser carton as a cushion and l ay the dispens er down on it s back. Re move the bolts holding th e skid to the mac hine, and separ ate the skid f rom the di spenser.
Ice Mach ine Install atio n CD300 Page 5 All models: P lace the dispenser in the location where it will be used. Level the top edge of the dispenser front to back an d left to right w ith the adjusta ble legs. Place the i ce machi ne on the dis penser and sec ure it to the dispenser w ith the hardwar e and straps.
Util ity C onnections C D300 Page 6 Drain Connections -Follow all appli cable codes. As ice mel ts in the dispenser , the water must be drain ed away. It i s critical that a pr oper drain b e connected to the dispenser.
Init ial Start U p and U se CD300 Page 7 Final Check List 1. Is the ice machine properl y installed? 2. Is the disp enser level? 3. Has the w ater supply been co nnected to the i ce machine? 4.
Sanitatio n / Maintena nce CD300 Page 8 Schedule An ice sy stem repres ents a sizable i nvestment of ti me and money in any compa ny’s busi ness. In order to receiv e the best retur n on that i nvestment, peri odic maintenance is required. I t is the user responsibility to see t hat the machine is properly m aintained .
Component Identificati on CD300 Page 9 View w hen sink assembly i s removed. Rotor as seen fr om the top. Inside v iew of ice chute. Rot or shaft..
Main tenance CD300 Page 10 Regular inspection and m aintenanc e will provi de the bes t assurance o f trouble f ree operation . Begin by removing the si nk assembly . Check the a ction of the ice chute a nd return spr ings. Retu rn Sprin gs Check and T ighten Fast eners Clean out t he lower drai n pan.
Service Diagnosis CD 300 Page 11 Symptom Probable Cause Possible Corre ction Does not disp ense. No power to dispenser. Check for power . Ice chute not all the w ay up. Push ice chu te up. No ice in hopper. Check ice mac hine, it may be off or the dispenser’s storage cap acity may hav e been ex ceeded.
Ad justments CD300 Page 12 The gear motor cam mu st be properly adj ust ed to properly position the dispensing rotor. 1. Disconnect el ectrical power to the di spenser. 2. Locate t he sink key , unlock sink and r emov e it from the dispenser . 3. Observe the position of th e rotor throug h the cube chute.
Removal and Replacement CD300 Page 13 Rotor 1. Disconnect el ectrical power to the di spenser and i ce machine. 2. At the back, r emov e two bolts s ecuring the ice mac hine to the dis penser. If a bin thermostat i s being used, p ull the ther m ostat capillary tube up and out of the ho pper.
Wirin g Diagra m CD300 Page 14 Button Dispensing Model CD300P.
Schematic Diagram CD300 Page 15 Button Dispensing Model CD300P.
Wirin g Diagra m CD300 Page 16 Coin Mechanism CD300C.
Schematic Diagram CD300 Page 17 Coin Mechanism CD300C CD300C.
Wirin g Diagra m CD300 Page 18 Key Card CD300K.
Schematic Diagram CD300 Page 19 Key Card CD300C CD300K.
Befo re Callin g Fo r Service CD300 Page 20 Check thes e things. 1. Is the disp enser plugged i n? 2. Has the dispe nser’s internal sw itch been switched to the ON position? 3. Is the ice machine plug ged in? 4. Has the ice machine’s int ernal sw itch been switched to the ON position? 5.
デバイスIce-O-Matic CD300の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ice-O-Matic CD300をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIce-O-Matic CD300の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ice-O-Matic CD300の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ice-O-Matic CD300で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ice-O-Matic CD300を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIce-O-Matic CD300の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ice-O-Matic CD300に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIce-O-Matic CD300デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
