Ingersoll-Randメーカー8670-( )-3( )の使用説明書/サービス説明書
ページ先へ移動 of 20
--- OPERATOR's MANUAL SECTlON M105 MANUAL 40 INCLUDING: OPERATION, INSTALLATION & MAINTENANCE Released: 4/77 Revised: 8- 30-96 Form: 1022-2 SELF-FEED DRILL Models 8670-( )-1( ) and 8670-( )-3.
MODEL IDENTIFICATION TABLE 2 The ARO@ model 8670-( ) self-feed drill is designed to automati- tally feed to a pre-set depth, trip and return. The models 8670-( ) are available with either a 1 -1/2” or 3” stroke length and in five (5) different spindle speeds.
top of valve housing. The unit will immediately retract to the initial position, whereupon the unit will stop with all air to the unit shut off. The needle type retract feed control valve regulates the flow of air from the piston, thus regulating the rate of retraction of the unit.
AIR AND LUBE REQUIREMENTS Air pressure of 90 p.s.i.g. (6 bar) at the air inlet of the tool is re- quired for maximum motor efficiency. If necessary, an air regulator should be installed to maintain this pressure when tool is in opera- tion.
M105 40 ---- * 44957 NAMEPLATE FOR NON-EU MODELS 44957-EU FOR “-EU” MODELS PARTS MARKED THUS - ARE INCLUDED IN SERVICE KIT NUMBER 45832, SEE PAGE 20.
GEARING SECTION DISASSEMBLY a. Secure motor housing (45168) in a suitable holding device and remove chuck, bearing lock nut (45158) and bearing lock screw (45159).
M105 40 15161 PARTS MARKED THUS ARE INCLUDED IN SERVICE KIT NUMBER 45632, SEE PAGE 20. * POSlTlON BEARINGS WITH SHIELDED SIDE AS SHOWN. 7.
MOTOR SECTION DISASSEMBLY a. Remove motor from tool as outlined on page 4. Remove motor assembly from housing as outlined in paragraph “a” of gear- ing disassembly.
NOTE: When assembling needle valves (34617), install with M105 b. top of needle valve flush with top of valve block (44927). Assemble valve assembly (45174) to valve housing (44919) 40 with gasket (44948) and nameplate (45184) and secure with five screws (Y211-109) and washers (Y14-10) NOTE: When replacing gaskets, torque cap screws to 20 in.
HOUSING AND VALVE SECTION DISASSEMBLY a. Remove three cap screws (Y211-102), with lock washers b. (Y14-10), and remove striker plate (44987). Grasp end of valve stem (44981) and pull valve components from housing. c. Remove bushing (44982) from housing for access to two “0” rings (Y325-210) and washer (F21-38).
TYPICAL CROSS SECTION OF TOOL 11.
ACCESSORIES HYDRAULIC CHECK TRIP BRACKET 44910 MOUNTING BRACKET (3 POSITION ADJUSTMENT) NOTE: Hydraulic check assembly (44969-1) is furnished with models 8670( )-1 and 44969-2 is furnished with models 8670-( )-3. HYDRAULIC CHECK: The hydraulic check assembly is a hermetically sealed unit with a frictionless diaphragm.
DOUBLE HYDRAULIC CHECK ASSEMBLIES 46133-( ) 46132 BRACKET Y99-43 CAP SCREW (2) HYDRAULlC CHECK CHECK HYDRAULlC HYDRAULIC ASSEMBLY NO. "A" CHECK "B" 46133-11 38922 38922 46133-12 38922 38922-1 46133-13 30922 38922-2 46133-22 38922-1 30922-1 46133-23 38922-1 38922-2 I 38133-33 38922-2 38922-2 I HYDRAULIC CHECK NO.
ACCESSORIES 45185 FOOT MOUNT ASSEMBLY 45188 NOSE HOUSING ? / 14.
RECOMMENDED POWER AIR INLET SYSTEM M105 40 Your ARO self-feed tool is designed to deliver specific horsepowerand thrust to achieve high rates of work. To assure the unit will develop this power, care must be taken that the power air Inlet system Is correctly sized to permit the proper rate of air flow.
BASIC REMOTE CONTROL FOR START AND EMERGENCY RETRACT FUNCTIONS REMOTE OPERATION Remote operation of the unit may be achieved by connecting a 3-way valve to the remote start and/or remote retract ports, as shown above. TO START: Depress the remote start button momentarily.
# 3 PORT (EXHAUST) REMOTE VALVE I (DUPLICATE FOR REMOTE RETRACT CIRCUIT, EXCEPT USE MODEL 461-2 PALM VALVE WITH RED BUTTON) WHEN MORE THAN EIGHT (6 TOOLS ARE REQUIRED PROVIDE ANOTHER 29192 VALVE AND 37750 MANIFOLD. THE SECOND SET OF TOOLS CAN BE ACTUATED FROM THE SAME 3-WAY PALM VALVE.
TROUBLE SHOOTING LISTED BELOW ARE SOME OF THE MOST COMMON CAUSES FOR THE SELF-FEED DRILL TO MALFUNCTION. MALFUNCTIONS BEYOND THE SCOPE OF THIS MANUAL SHOULD BE BROUGHTTO THE ATTENTlON OF YOUR ARO REPRESENTATIVE OR RETURN THE TOOL TO THE FACTORY FOR REPAIR.
“TOOL RETRACTED” PORT.
SERVICE KIT NO. 45832 Qty 5 1 1 1 1 3 1 1 1 2 1 2 2 1 1 1 1 3 1 2 2 5 PART NUMBER 15066 33017 34690 35963 37942 39679 41795 41799 41954 42321 42639 44915-4 44915-5 44945 44948 44950 44956 44967 44968 .
デバイスIngersoll-Rand 8670-( )-3( )の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Ingersoll-Rand 8670-( )-3( )をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIngersoll-Rand 8670-( )-3( )の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ingersoll-Rand 8670-( )-3( )の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ingersoll-Rand 8670-( )-3( )で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ingersoll-Rand 8670-( )-3( )を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIngersoll-Rand 8670-( )-3( )の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ingersoll-Rand 8670-( )-3( )に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIngersoll-Rand 8670-( )-3( )デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。