IntelメーカーGA-4MXSVの使用説明書/サービス説明書
ページ先へ移動 of 71
USER’S MANUAL GA-4MXSV Pentium Prescott 1066 Motherboard Pentium ® Prescott Processor Motherboard Rev. 1002 12ME-4MXSV -1002.
2 English GA-4MXSV Motherboard T able of Content Item Checklist ........................................................................................ 4 WARNING! .......................................................................................
English 3 T able of Content Chapter 4 T echnical Reference ............................................................ 61 Block Diagram ........................................................................................... 6 1 Chapter 5 Driver Installation .
4 English GA-4MXSV Motherboard Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. T o protect them against damage from static electricity, you should follow some precautions whenever you work on your computer.
5 Introduction Chapter 1 Introduction Features Summary Form Factor 12” x 9.6” A TX size form factor , 6 layers PCB. CPU Supports Intel ® Pentium Prescot and Smithfieldprocessor Intel .
6 English GA-4MXSV Motherboard On-Board Graphic A TI ES1000 with 16Mb DDR SDRAM On-Board LAN Dual Intel 82573V Gigabit Ethernet controllers Hardware Monitor Winbond 83792D controller Enhanced features with CPU Vcore, 1.5V reference, VCC3 (3.
7 Introduction GA-4MXSV Motherboard Layout B C D A E G H I F J K L M N O O P Q R S T U V W X Y Z 1 2 5 6 7 8 9 3 4.
8 English GA-4MXSV Motherboard A. CPU U. PCI_B B. Intel Mukilteo V PCI_A C. Intel 6702 PXH-V W. PCI-E x8 D. Intel ICH7R X. PCI-X_2 E. ITE IT8712F Y. PCI-X_1 F. SA T A1 Z. BA T (Battery) G. SA T A2 1. AT X H. SA T A3 2. A TX12V I. SA T A4 3. WOR J. FDC 4.
9 Connector Introduction T o set up your computer , you must complete the following steps: Step 1- Install the Central Processing Unit (CPU) Step 2- Install memory modules Step 3- Install expansion ca.
10 English GA-4MXSV Motherboard Step 1: Installing Processor and CPU Haet Sink Before installing the processor and cooling fan, adhere to the following cautions: Step1-1: Installing CPU Step 1 Gently lift the metal lever located on the CPU socket to the upper-right position.
11 Hardware Installation Process Step1-2: Installing Heat Sink Fig.1 Please apply heatsink paste on the surface of the installed CPU. Fig. 2 ( to remove the heatsink, turning the push pin along the direction of arrow; and reverse the previous step to install the heat sink.
12 English GA-4MXSV Motherboard Step 2: Install memory modules Before installing the processor and heatsink, adhere to the following warning: When DIMM LED is ON, do not install/remove DIMM from socket. GA-4MXSV has 4 dual inline memory module (DIMM) socets.
13 Hardware Installation Process T able 1. Supported DIMM Module T ype T able 2. DIMM Placement DDR2-533/667 T echnology Organization SDRAM Chips/DIMM 256MB 8MB x 8 x 4 bks 8 16MB x 4 x 4bks 16 512MB .
14 English GA-4MXSV Motherboard Step 3: Install expansion cards 1. Read the related expansion card’s instruction document before install the expansion card into the computer. 2. Remove your server’s chassis cover, necessary screws and slot bracket from the computer.
15 Hardware Installation Process Step 4: Connect ribbon cables, cabinet wires, and power supply Step 4-1 : I/O Back Panel Introduction .
16 English GA-4MXSV Motherboard LAN LED Description Color Condition Description Green O N LAN Link / no Access Green BLINK LAN Access - O FF Idle Green O N 100Mbps connection - OF F 10Mbps connection .
17 Connector Introduction Step 4-2 :Connectors & Jumper Setting Introduction A ) A T X M) WOR1 B ) A TX _12V N ) UF1 (CPU Fan) C) IDE1 O ) UF2 (System Fan) D ) FDC1 P) UF3 (System Fan) E) F_Panel .
18 English GA-4MXSV Motherboard A) A TX (A TX Power Connector) B ) A TX_12V( +12V Power Connector) This connector (A TX +12V) is used only for CPU1 Core V oltage. Pin No. Definition 1 GND 2 GND 3 GND 4 GND 5 P12V_CPU 6 P12V_CPU 7 P12V_CPU 8 P12V_CPU PIN No.
19 Connector Introduction C ) IDE1 (IDE Connector) Please connect first harddisk to IDE1. The red stripe of the ribbon cable must be the same side with the Pin1. 2 1 39 40 D) FDC1 (Floppy Connector) Please connect the floppy drive ribbon cables to FDD.
20 English GA-4MXSV Motherboard E ) F_Panel1 (2X9 Pins Front Panel connector) Please connect the power LED, PC speaker, reset switch and power switch of your chassis front panel to the F_P ANEL connector according to the pin assignment above.
21 Connector Introduction Pin No. Definition 1 DCD- 2 SIN2 3 SOUT2 4 DTR2- 5 GND 6 DSR2- 7 RTS2- 8 CTS2- 9 RI2- 10 N C F ) COM2 1 2 91 0 G ) USB2 (Front USB Connector) Be careful with the polarity of the front panel USB connector. Check the pin assignment while you connect the front panel USB cable.
22 English GA-4MXSV Motherboard Y ou can connect the Serial A T A device to this connector, it provides you high speed transfer rates (150MB/sec). H / I / J / K ) S_A T A1/ 2/ 3/ 4 (Serial A T A Connectors) 1 7 S_A T A1 S_A T A 2 S_A T A3 S_A T A 4 Pin No.
23 Connector Introduction M ) WOR1 (Wake on Ring) 1 Pin No. Definition 1 MODEM RING ON 2 GND N ) UF1 (CPU Fan Connector) Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running under abnormal condition or damaged by overheating.
24 English GA-4MXSV Motherboard O / P / Q / R ) UF2/3/4/5 (System Fan Connectors) This connector allows you to link with the cooling fan on the system case to lower the system temperature. These connectors are for system use only. UF2 UF3 UF4 UF5 1 1 Pin No.
25 Connector Introduction T ) RECOVERY ( BIOS Recovery Function) 1 1 1-2 close: Enable BIOS Recovery function. 2-3 close: Disable this function. (Default value) Please remove the jumper when system access recovery flopp disk.
26 English GA-4MXSV Motherboard V ) BA T1 (Battery) CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
27 BIOS Setup < Ç > Move to previous item < È > Move to next item < Å > Move to the item in the left hand < Æ > Move to the item in the right hand <Esc> Main Menu - Q.
28 GA-4MXSV Motherboard z z z z z Main This setup page includes all the items in standard compatible BIOS. z z z z z Adva nced This setup page includes all the items of AMI special enhanced features. (ex: Auto detect fan and temperature status, automatically configure hard disk parameters.
29 BIOS Setup Syste m Ti me The time is calculated based on the 24-hour military time clock. Set the System Time (HH:MM:SS) Syste m Date Set the System Date. Note that the “Day” automatically changed after you set the date.
30 GA-4MXSV Motherboard Lega cy Diskette A/B This category identifies the type of floppy disk drive A that has been installed in the computer . Disabled Disable this device. 360KB, 5 1/4 in. 3 1/2 inch A T -type high-density drive; 360K byte capacity 1.
31 BIOS Setup TYPE 1-39: Predefined types. Users: Set parameters by User. Auto: Set parameters automatically . (Default Vaules) CD-ROM: Use for A T API CD-ROM drives or double click [Auto] to set all HDD parameters automatically. A T API Removable: Removable disk drive is installed here.
32 GA-4MXSV Motherboard Advanced Processor Options Figure 1-1: Advanced Processor Option Adva nced Proce ssor Option This category includes the information of CPU Speed, Processor ID, Processor L2 Cache . And setup menu for C1 Enhanced Mode, No Execute Mode Memory Protection , and Processor Power Management.
33 BIOS Setup C1 Enha nced Mode With enabling C1 Enhanced Mode, all loical processors in the physical processor have entered the C1 state, the processor will reduce the core clock frequency to system bus ratio and VID. Enabled Enabled C1 Enhanced Mode.
34 GA-4MXSV Motherboard Figure 2: Advanced Adva nced About This Section: Advanced With this section, allowing user to configure your system for basic operation. User can change the processor options, chipset configuration, PCI configuration and chipset control.
35 BIOS Setup Memory Configuration Figure 2-1: Memory Configuration Installed Memor y/A vailable to OS/DIMM Group 1,2,3,4 Status These category is display-only which is determined by POST (Power On Self T est) of the BIOS. Memory Reset Y es Select ‘Y es’, system will clear the memory error status.
36 GA-4MXSV Motherboard PCI Configuration Figure 2-2: PCI Configuration Embedded NIC #1 Onboard LAN1 Control Enabled Enable onboard LAN1 device. (Default value) Disabled Disable this function. Option ROM Scan Enabled Enableing this item to initialize device expansion ROM.
37 BIOS Setup PCI Slot 1/2/3/4/5 Option ROM Enabled Enableing this item to initialize device expansion ROM. (Defualt value) Disabled Disable this function.
38 GA-4MXSV Motherboard I/O Device Configuration Figure 2-3: I/O Device Configuration.
39 BIOS Setup Serial Port A This allows users to configure serial prot A by using this option. Enabled Enable the configuration (Default value) Disabled Disable the configuration. Base I/O Address/IRQ 3F 8 Set IO address to 3F8.
40 GA-4MXSV Motherboard Parallel Port This allows users to configure parallel port by using this option. Enabled Enable the configuration. Disabled Disable the configuration. (Default value) Mode This option allows user to set Parallel Port transfer mode.
41 BIOS Setup USB 2.0 Controller This item allows users to enable or disable the USB 2.0 device by setting item to the desired value. Enabled Enable USB 2.0 controller. (Default value) Options Disbale this function. Legacy USB Support This option allows user to function support for legacy USB.
42 GA-4MXSV Motherboard Seri al A T A Enabled Enables on-board serial A T A function. (Default V alue) Disabled Disables on-board serial A T A function. ` Native Mode Operation This option allows user to set the native mode for Serial A T A function.
43 BIOS Setup Advanced Chipset Control Figure 2-4: Advanced Chipset Control Ena ble Multi media Ti mer Enabled Enable Multimedia Timer support. Disabled Disable this function. (Default value) PCI Express Sub-Menu These items are for debugging the PCI-Express Ports.
44 GA-4MXSV Motherboard W ake On LAN / PME This option allow user to determine the action of the system when a LAN/PME wake up event occurs. Enabled Enable Wake On LAN/PME. (Default value) Disabled Disable this function. Note: This item must enabled if you’re running under Windows operating system.
45 BIOS Setup Hardware Monitor Figure 2-5: Hardware Monitor CPU / Motherboard/ Ambit T emperature Display the current CPU temperature, Motherboard, and Ambient temperature. V oltage Monitor: 3V Dual, VCC3, VCC, 12V2, 12V1, VBA T , 5VSB Detect system's voltage status automatically.
46 GA-4MXSV Motherboard Boot -ti me Di agnostic When this item is enabled, system will shows Diagnostic status when system boot. Enabled Enable Boot-time Diagnostic. Disabled Disable this function. (Default value) Re set Configuration Data Y e s Reset all configuration data.
47 BIOS Setup Security Figure 3: Security Set User Password Y ou can only enter but do not have the right to change the options of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password.
48 GA-4MXSV Motherboard Set Supervisor Password Y ou can install and change this options for the setup menus. T ype the password up to 6 characters in lengh and press <Enter>. The password typed now will clear any previously entered password from the CMOS memory .
49 BIOS Setup Server Figure 4: Server.
50 GA-4MXSV Motherboard System Management Figure 4-1: System Management Server M a nagement This category allows user to view the server management features. Including information of BIOS V ersion . All items in this menu cannot be modified in user’s mode.
51 BIOS Setup Figure 4-2: Console Redirection Console Redirection BIOS Redirection Port If this option is set to enabled, it will use a port on the motherboard. On-board COMA Use COMA as he COM port address. Disabled Disable this function.
52 GA-4MXSV Motherboard Flow Control This option provide user to enable the flow control function. None Not supported. XON/OFF S oftware control.
53 BIOS Setup Post Error Pause If this item is set to enabled, the system will wai for user intervention on critical POST errors. If this item is disabled, the system will boot with no intervention if possible. Enabled Enable Post Error Pause.
54 GA-4MXSV Motherboard Event Log Viewer Enabled Enable Event Log Viewer function(Default value) Disabled Disable this function.
55 BIOS Setup Figure 4-4: Set Threshold Set Threshold Syste m Fa n 1/2/3/4/5/6 Error Enabled Enable System Fan 1/2/3/4/5/6 Fan Error. (Default value) Disabled Disable this function. M/B V oltage Err or Enabled Motherboard Voltage Error.
56 GA-4MXSV Motherboard Boot Figure 5: Boot Boot Priority Order This field determines which type of device the system attempt to boot from after PhoenixBIOS Post completed. Specifies the boot sequence from the available devices. If the first device is not a bootable device, the system will seek for next available device.
57 BIOS Setup Exit Figure 6: Exit * * * * * About This Section: Exit Once you have changed all of the set values in the BIOS setup, you should save your chnages and exit BIOS setup program. Select “Exit” from the menu bar, to display the following sub-menu.
58 GA-4MXSV Motherboard Exit Saving Cha nge s This option allows user to exit system setup with saving the changes. Press <Enter> on this item to ask for the following confirmation message: Pressing ‘Y’ to store all the present setting values tha user made in this time into CMOS.
59 BIOS Setup Discard Cha nge s This option allows user to load previos values from CMOS for all setup item. When you press <Enter> on this item, you will get a confirmation dialog box with a message as below: Load Settup Default This option allows user to load default values for all setup items.
60 GA-4MXSV Motherboard Save Cha nge s This option allows user to save setup dat ato CMOS. When you press <Enter> on this item, you will get a confirmation dialog box with a message as below: Press [Y es] to save setup daya to CMOS.
61 T echnical Reference Revision History Chapter 4 T echnical Reference Intel LGA775 Smithfield 1066MT/S FSB ICH7R VR D 10.1 Clock Generator CK410 ICS 95410DF VID0~5 Cha nnel A DD RII533/667 U nbuffer.
GA-4MXSV Motherboard 62 A. Intel Chipset Software Installation Utilities Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show a series of Setup Wizard dialog boxes. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.
63 Driver Installation 5. Installation completed, Click "Finish" to restart computer. (5) Installation Completed.
GA-4MXSV Motherboard 64 B. Intel LAN Driver Installation (1) Auto Run window (2) Intel LAN Drivers 1.Click "Intel LAN Driver" item. Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show a series of Setup Wizard dialog boxes.
65 Driver Installation Install Option (5) 5.Click "Next". (6) Start Installation 6.Click "Install". Installation Progress Installation Complete Starting Installation (7) (8) 8.
GA-4MXSV Motherboard 66 C. Intel Host RAID Driver Installation Installation Procedures: 1. The CD auto run program starts, Double click on “Intel Host RAID Driver” to make a driver disk. 2. Select a folder refering to your operating system. 3. Insert a flopp disk in the floppy drive.
67 Driver Installation Formatting and writing in floppy sidk (5).
GA-4MXSV Motherboard 68 D. VGA ES1000 Driver Installation Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show a series of Setup Wizard dialog boxes. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.
69 Driver Installation (3) (2) (1) (4) E . DirectX 9.0 Driver Installation Auto Run window License Agreement Starting Installaiton 4.Click "Finish" to complete the installation.
GA-4MXSV Motherboard 70 Acronyms Meaning ACPI A d vanced Configuration and Power Interface A P M Advanced Power Management A G P Accelerated Graphics Port A M R Audio Modem Riser A C R Advanced Commun.
71 Appexdix Acronyms Meaning I / O Input / Output IOAPIC Input Output Advanced Programmable Input Controller I S A Industry Standard Architecture L A N Local Area Network L BA Logical Block Addressing.
デバイスIntel GA-4MXSVの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Intel GA-4MXSVをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIntel GA-4MXSVの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Intel GA-4MXSVの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Intel GA-4MXSVで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Intel GA-4MXSVを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIntel GA-4MXSVの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Intel GA-4MXSVに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIntel GA-4MXSVデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。