IntelメーカーGA-8I915G-ZFDの使用説明書/サービス説明書
ページ先へ移動 of 72
GA-8I915G-ZFD Intel ® Pentium ® 4 LGA775 Processor Motherboard User's Manual Rev . 1 101 12ME-I915GZFD-1 101.
Copyright © 2005 GIGA-BYTE TECHNOLOGY CO., L TD. All rights reserved. The trademarks mentioned in the manual are legally registered to their respective companies.
- 3 - T able of Contents GA-8I915G-ZFD Motherboard Layout ........................................................................... 5 Block Diagram .....................................................................................................
- 4 - Chapter 3 Install Drivers ............................................................................................ 43 3-1 Install Chipset Drivers ................................................................................... 43 3-2 Software Applications .
- 5 - GA-8I915G-ZFD Motherboard Layout KB_MS CPU_FAN VGA LPT AT X GA-8I915G-ZFD IT8712 SPDIF_IN COMA BIOS PWR_LED F_P ANEL F1_1394 F_USB1 CODEC LGA775 BA T TSB43AB23 RTL81 10S S_A T A0 ICH6 PCI1 DDR1 .
- 6 - Block Diagram TSB43AB23 3 IEEE1394 LGA775 Processor CPUCLK+/-(200/133MHz) VGA BIOS 33MHz 14.318MHz DDR400/333MHz DIMM Host Interface Intel 915G GMCH GMCHCLK (200/133MHz) 66MHz 48MHz PCI Bus 2 Se.
- 7 -.
- 8 -.
Hardware Installation - 9 - English 1-1 Considerations Prior to Installation Preparing Y our Computer The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow the instructions below: 1.
GA-8I915G-ZFD Motherboard - 1 0 - English CPU Supports the latest Intel ® Pentium ® 4 LGA775 CPU Supports 800/533MHz FSB L2 cache varies with CPU Chipset Northbridge: Intel ® 915G E.
Hardware Installation - 11 - English 1-3 Installation of the CPU and Heatsink Before installing the CPU, please comply with the following conditions: 1. Please make sure that the motherboard supports the CPU. 2. Please take note of the one indented corner of the CPU.
GA-8I915G-ZFD Motherboard - 1 2 - English 1 . The DIMM slot has a notch, so the DIMM memory module can only fit in one direction. 2 . Insert the DIMM memory module vertically into the DIMM slot. Then push it down. 3 . Close the plastic clip at both edges of the DIMM slots to lock the DIMM module.
Hardware Installation - 13 - English GA-8I915G-ZFD supports the Dual Channel T echnology . After operating the Dual Channel T echnology , the bandwidth of Memory Bus will double.
GA-8I915G-ZFD Motherboard - 1 4 - English 1-6 I/O Back Panel Introduction PS/2 Keyboard and PS/2 Mouse Connector T o install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard o the lower port (purple). IEEE 1394 port Connects to IEEE 1394 devices.
Hardware Installation - 15 - English 1) A TX_12V 2) A TX (Power Connector) 3) CPU_F AN 4) SYS_FAN 5) I D E 6) S_A T A0 / S_A T A1 7 ) F_P ANEL 8 ) PWR_LED 9 ) AZALIA_FP 1 0 ) CD_IN 1 1) F_USB1 / F_USB.
GA-8I915G-ZFD Motherboard - 1 6 - English 1/2) A TX_12V/A TX (Power Connector) With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, please make sure that all components and devices are properly installed.
Hardware Installation - 17 - English 1 CPU_F AN SYS_FAN 1 3/4) CPU_F AN / SYS_F AN (Cooler Fan Power Connector) The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin (only for CPU_FAN) power connector and possesses a foolproof connection design.
GA-8I915G-ZFD Motherboard - 1 8 - English 1 7 Pin No. Definition 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND 6 ) S_A T A0/S_A T A1 (Serial A T A Connector , Controlled by ICH6) Serial A T A can provide up to 150MB/s transfer rate. Please refer to the BIOS setting for the Serial A T A and install the proper driver in order to work properly .
Hardware Installation - 19 - English 1 Pin No. Definition 1 MPD+ 2 MPD- 3 MPD- 1 9 2 10 9 ) AZALIA_FP(Front Audio Panel Connector) This connector is supported to connect HD(High Definition) Audio and AC'97 Audio.
GA-8I915G-ZFD Motherboard - 2 0 - English 1 0 ) CD_IN (CD IN) Connect CD-ROM or DVD-ROM audio out to the connector. Pin No. Definition 1 CD-L 2 GND 3 GND 4 CD -R 1 2 9 1 1 ) F_ USB1 / F_USB2 (Front USB Connector) Be careful with the polarity of the front USB connector.
Hardware Installation - 21 - English 2 10 1 9 Pin No. Definition 1 TP A2+ 2 TP A2- 3 GND 4 GND 5 TPB2+ 6 TPB2- 7 No Pin 8 Power 9 Power 10 GND 1 2 ) F1_1394 (IEEE 1394 Connector) Serial interface standard set by Institute of Electrical and Electronics Engineers, which has features like high speed, high bandwidth and hot plug.
GA-8I915G-ZFD Motherboard - 2 2 - English 1 4 ) CLR_CMOS (Clear CMOS) Y ou may clear the CMOS data to its default values by this jumper . T o clear CMOS, temporarily short 1-2 pin. Default doesn't include the "Shunter" to prevent from improper use this jumper.
BIOS Setup - 23 - English BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure required settings or to activate certain system features. The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard.
GA-8I915G-ZFD Motherboard - 2 4 - English The Main Menu (For example: BIOS V er . : FB) Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.
BIOS Setup - 25 - English Load Optimized Defaults Optimized Defaults indicates the value of the system parameters which the system would be in best performance configuration. Set Supervisor Password Change, set, or disable password.
GA-8I915G-ZFD Motherboard - 2 6 - English 2-1 Standard CMOS Features Date The date format is <week>, <month>, <day>, <year>. Week The week, from Sun to Sat, determined by the BIOS and is display only Month The month, Jan. Through Dec.
BIOS Setup - 27 - English IDE Channel 2/3 Master, Slave IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection. Extended IDE Drive SA T A devices setup. Y ou can use one of two methods: Auto Allows BIOS to automatically detect SA T A IDE devices during POST .
GA-8I915G-ZFD Motherboard - 2 8 - English 2-2 Advanced BIOS Features Hard Disk Boot Priority Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc. Use < > or < > to select a device, then press<+> to move it up, or <-> to move it down the list.
BIOS Setup - 29 - English Password Check Setup The system will boot but will not access to Setup page if the correct password is not entered at the prompt. (Default value) System The system will not boot and will not access to Setup page if the correct password is not entered at the prompt.
GA-8I915G-ZFD Motherboard - 3 0 - English 2-3 Integrated Peripherals On-Chip Primary PCI IDE Enabled Enable onboard 1st channel IDE port. (Default value) Disabled Disable onboard 1st channel IDE port. On-Chip SA T A Mode Disabled Disable this function.
BIOS Setup - 31 - English Enhanced Set On-Chip SAT A mode to Enhanced, the motherboard allows up to 6 HDDs to use. Non-Combined Set On-Chip SAT A mode to Non-Combined, SA T A will be simulated to P A T A mode. P A T A IDE Set to Ch.1 Master/Slave Set P A T A IDE to Ch.
GA-8I915G-ZFD Motherboard - 3 2 - English Onboard LAN Boot ROM This function decide whether to invoke the boot ROM of the onboard LAN chip. Enabled Enable this function. Disabled Disable this function. (Default value) Onboard Serial Port 1 Auto BIOS will automatically setup the port 1 address.
BIOS Setup - 33 - English 2-4 Power Management Setup ACPI Suspend T ype S1(POS) Set ACPI suspend type to S1/POS(Power On Suspend). (Default value) S3(STR) Set ACPI suspend type to S3/STR(Suspend T o RAM). Soft-off by PWR-BTTN Instant-off Press power button then Power off instantly.
GA-8I915G-ZFD Motherboard - 3 4 - English Power On By Keyboard Password Enter from 1 to 5 characters to set the Keyboard Power On Password. Disabled Disabled this function. (Default value) Keyboard 98 If your keyboard have "POWER Key" button, you can press the key to power on the system.
BIOS Setup - 35 - English 2-5 PnP/PCI Configurations PCI 1 IRQ Assignment Auto Auto assign IRQ to PCI 1. (Default value) 3,4,5,7,9,10,1 1,12,14,15 Set IRQ 3,4,5,7,9,10,1 1,12,14,15 to PCI 1. PCI 2 IRQ Assignment Auto Auto assign IRQ to PCI 2. (Default value) 3,4,5,7,9,10,1 1,12,14,15 Set IRQ 3,4,5,7,9,10,1 1,12,14,15 to PCI 2.
GA-8I915G-ZFD Motherboard - 3 6 - English 2-6 PC Health Status Current V oltage(V) Vcore / DDR25V / +3.3V / +12V Detect system's voltage status automatically. Current System/CPU T emperature Detect System/CPU temperature automatically. Current CPU/SYSTEM F AN Speed (RPM) Detect CPU/SYSTEM Fan speed status automatically.
BIOS Setup - 37 - English 2-7 MB Intelligent T weaker(M.I.T .) Incorrect using these features may cause your system broken. For power end-user use only. CMOS Setup Utility-Copyright (C) 1984-2005 A ward Software MB Intelligent T weaker(M.I.T .) CPU Clock Ratio (Note) [16X] C.
GA-8I915G-ZFD Motherboard - 3 8 - English CPU Host Clock Control Please note that if your system is overclocked and cannot restart, please wait 20secs. for automatic system restart or clear the CMOS setup data and perform a safe restart. Disabled Disable CPU Host Clock Control.
BIOS Setup - 39 - English 2-8 Load Fail-Safe Defaults Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance.
GA-8I915G-ZFD Motherboard - 4 0 - English 2-10 Set Supervisor/User Password When you select this function, the following message will appear at the center of the screen to assist you in creating a password. T ype the password, up to eight characters, and press <Enter>.
BIOS Setup - 41 - English 2-1 1 Save & Exit Setup T ype "Y" will quit the Setup Utility and save the user setup value to RTC CMOS. T ype "N" will return to Setup Utility . 2-12 Exit Without Saving T ype "Y" will quit the Setup Utility without saving to RTC CMOS.
GA-8I915G-ZFD Motherboard - 4 2 - English.
Install Drivers - 43 - English Chapter 3 Install Drivers Pictures below are shown in Windows XP. Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device icon in "My computer", and execute the Run.
GA-8I915G-ZFD Motherboard - 44 - English 3-2 Software Applications This page displays all the tools that Gigabyte developed and some free software, you can choose anyone you want and press "install" to install them. 3-3 Driver CD Information This page lists the contents of software and drivers in this CD-title.
Install Drivers - 45 - English 3-4 Hardware Information This page lists all device you have for this motherboard. 3-5 Contact Us Please see the last page for details.
GA-8I915G-ZFD Motherboard - 46 - English.
Appendix - 47 - English Chapter 4 Appendix 4-1 Unique Software Utilities M.I.T . (Motherboard Intelligent T weaker) Motherboard Intelligent T weaker (M.I.T .) allows user to access and change BIOS feature settings with relative speed and ease. Through GIGABYTE M.
GA-8I915G-ZFD Motherboard - 48 - English 4-1-1 Xpress Recovery Introduction What is Xpress Recovery ? Xpress Recovery is a utility used to back up and restore an OS partition. If the hard drive is not working properly, the user can restore the drive to its original state.
Appendix - 49 - English 2. Press F9 during powering on the computer. (T ext Mode) Xpress Recovery V1.0 (C) Copy Right 2003. GIGABYTE T echnology CO. , Ltd. 1. Execute Backup Utility 2. Execute Restore Utility 3. Remove Backup Image 4. Set Password 5. Exit and Restart 1.
GA-8I915G-ZFD Motherboard - 50 - English 1. Execute Backup Utility: Press B to Backup your System or Esc to Exit The backup utility will automatically scan your system and back up data as a backup image in your hard drive. Not all systems support access to Xpress Recovery by pressing the F9 key during computer power on.
Appendix - 51 - English 4-1-2 Flash BIOS Method Introduction Method 1 : Q-Flash TM Utility Q-Flash TM is a BIOS flash utility embedded in Flash ROM. With this utility, users only have to stay in the BIOS menu when they want to update BIOS. Q-Flash?allows users to flash BIOS without any utility in DOS or Windows.
GA-8I915G-ZFD Motherboard - 52 - English Entering the Q-Flash TM utility: CMOS Setup Utility-Copyright (C) 1984-2004 A ward Software Sta ndard CMOS Features Adva nced BIOS Features Integrated Peripherals Power Ma nagement Setup PnP/PCI Configurations PC Health Status MB Intelligent T weaker(M.
Appendix - 53 - English Dual BIOS Utility Boot From......................................... M ain Bios Main ROM T ype/Size............................
GA-8I915G-ZFD Motherboard - 54 - English 3. Press Y button on your keyboard after you are sure to update BIOS. Then it will begin to update BIOS. The progress of updating BIOS will be displayed. Dual BIOS Utility Boot From.............................
Appendix - 55 - English CMOS Setup Utility-Copyright (C) 1984-2004 A ward Software Sta ndard CMOS Features Adva nced BIOS Features Integrated Peripherals Power Ma nagement Setup PnP/PCI Configurations PC Health Status MB Intelligent T weaker(M.
GA-8I915G-ZFD Motherboard - 56 - English Exploring the Q-Flash TM utility screen The Q-FlashBIOS utility screen consists of the following key components. T ask menu for Q-Flash utility: Contains the names of three tasks. Blocking a task and pressing Enter key on your keyboard to enable execution of the task.
Appendix - 57 - English 3. Press Y button on your keyboard after you are sure to update BIOS. Then it will begin to update BIOS. The progress of updating BIOS will be shown at the same time. Q-Fla sh Utility V1.30 Fla sh T ype/Size....................
GA-8I915G-ZFD Motherboard - 58 - English Method 2 : @BIOS TM Utility If you do not have a DOS startup disk, we recommend that you use the new @BIOS utility. @BIOS allows users to update their BIOS under Windows. Just select the desired @BIOS server to download the latest version of BIOS.
Appendix - 59 - English III. Save BIOS In the very beginning, there is "Save Current BIOS" icon shown in dialog box. It means to save the current BIOS version. IV. Check out supported motherboard and Flash ROM: In the very beginning, there is "About this program" icon shown in dialog box.
GA-8I915G-ZFD Motherboard - 60 - English 4-1-3 2 / 4 / 5.1 / 7.1 Channel Audio Function Introduction There are 5 kinds of output mode: Earphone Output Mode, 2 / 4 / 5.1 / 7.1 Channel Output Mode. Earphone Output Mode -- Only earphone output is configured on the system.
Appendix - 61 - English Line Out 2 Channel Audio Setup: We recommend that you use speakers with amplifier to acquire the best sound effect if the stereo output is applied. STEP 1: Connect the stereo speakers or earphone to "Line Out". STEP 2: After installation of the audio driver, you'll find an icon in the system area.
GA-8I915G-ZFD Motherboard - 62 - English STEP 2: After installation of the audio driver, you'll find an icon in the system area. Double click the icon to select the function. 4 Channel Audio Setup STEP 1 : Connect the front speaker to "Front Speaker Out" and the surround speaker to "Surround speaker out".
Appendix - 63 - English 5.1 Channel Audio Setup STEP 1 : Connect the front speaker to "Front Speaker Out", the surround speaker to "Surround speaker out", and the center/subwoofer speaker to "Center/Subwoofer Speaker Out".
GA-8I915G-ZFD Motherboard - 64 - English 7.1 Channel Audio Setup STEP 1 : Connect the front speaker to "Front Speaker Out", the surround speaker to "Surround speaker out", and the center/subwoofer speaker to "Center/Subwoofer Speaker Out", and the back surround speaker to "Back surround speaker out".
Appendix - 65 - English Digital I/O Status: Digital Output Status-- (1) For stereo PCM output: sampling rate is shown here. (2) For Dolby Digital Live! output: AC3 is shown here. Digital Input Status-- (1) For stereo PCM input: sampling rate is shown here.
GA-8I915G-ZFD Motherboard - 66 - English 4-2 T roubleshooting Below is a collection of general asked questions. T o check general asked questions based on a specific motherboard model, please log on to http://www.gigabyte.com.tw Question 1: I cannot see some options that were included in previous BIOS after updating BIOS.
Appendix - 67 - English.
GA-8I915G-ZFD Motherboard - 68 - English.
Appendix - 69 - English.
GA-8I915G-ZFD Motherboard - 70 - English.
Appendix - 71 - English Contact Us T aiwan (Headquarters) GIGA-BYTE TECHNOLOGY CO., L TD. Address: No.6, Bau Chiang Road, Hsin-Tien, T aipei 231, T aiwan TEL: +886-2-8912-4888 F AX: +886-2-8912-4003 T ech. Support : http://tw .giga-byte.
GA-8I915G-ZFD Motherboard - 72 - English China NINGBO G.B.T . TECH. TRADING CO., L TD. T ech. Support : http://tw .giga-byte.com/T echSupport/ServiceCenter .htm Non-T ech. Support(Sales/Marketing) : http://ggts.gigabyte.com.tw/nontech.
デバイスIntel GA-8I915G-ZFDの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Intel GA-8I915G-ZFDをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIntel GA-8I915G-ZFDの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Intel GA-8I915G-ZFDの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Intel GA-8I915G-ZFDで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Intel GA-8I915G-ZFDを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIntel GA-8I915G-ZFDの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Intel GA-8I915G-ZFDに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIntel GA-8I915G-ZFDデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。