IntelメーカーP4LAの使用説明書/サービス説明書
ページ先へ移動 of 62
P4LA Industrial motherboard User ’ s Manual Edition: 1.00 2006/05/30.
P 4 L A U s e r ’ s M a n u a l 2 Copyright Copyright 2006. All rights reserved. This document is copyright ed and all rights are reserved. The information in this docume nt is subject to change without prior notice to make improvements to the products.
P4LA User ’s Manual Packing List 3 Packing List Please check package component before y ou use our products. Hardware: P4LA industrial motherboard x 1 Cable Kit: 40-pin A T A 100 IDE flat cable x 1 .
P 4 L A U s e r ’ s M a n u a l I n d e x 4 Inde x Chapter1 <Introduction> ..................................................................... 7 1.1 <Product Overview> ...................................................................
P 4 L A U s e r ’ s M a n u a l I n d e x 5 2.17 <Expansion Interface> ......................................................................... 33 Chapter 3 <System Configuration> ........................................... 35 3.1 <SA T A configuration> .
P 4 L A U s e r ’ s M a n u a l 6 (This Page is Lef t for Blank ).
P4LA User ’s Manual Introduction Product Ov erv iew 7 Chapter1 <Introduction> 1.1 <Product Overview> P4LA is the motherboard with last Intel desktop tec hnology with industrial motherboard form factor .
P4LA User ’s Manual Introduction Product Spe cification 8 1.2 <Product Specification> General Specification Form Factor Industrial motherboard CPU Intel ® Pentium 4 /Pentium D / Celeron D/ Co.
P4LA User ’s Manual Introduction Product Spe cification 9 Ethernet Interface Chipset 10/100/1000MT LAN interface with Marvell E8053 Type 10Base-T / 100Base-TX/1000Base-T, auto-switching Fast Ethernet Full duplex, IEEE802.
P4LA User ’s Manual Introduction Component Placement 10 1.3 <Component Placement> COM p ort ISA DOC CF AT X SA T A II DIMM PCI-Ex p ress PCI LPT LAN PS2 Serial p ort VGA A udio.
P4LA User ’s Manual Introduction Block Diagram 1 1 1.4 <Block Diagram> Intel Pentium 4 w ith 775 pin PLGA processo r Intel GMA950 Graphics PCI-Express 16x 8GB/s Intel 945G GMCH 4 x Serial A T A II ports 300MB/s 1 x Marvell E8053 Gigabit LAN 4 x PCI bus BIOS 6 x Serial ports 1 x Floppy port 8-bit GPIO SMBus 2.
P4LA User ’s Manual Introduction Mechanial Draw ing 12 1.5 <Mechanical Drawing >.
P 4 L A U s e r ’ s M a n u a l H a r d w a r e S e t u p Connector Location 13 Chapter 2 <Hardware Setup> 2.1 <Connector Location> ISA DOC JFRNT CN_ Audio CN_DIO CF SYSF AN AT X IDE1 FD.
P4LA User ’s Manual Introduction Jumper Reference 14 2.2 <Jumper Reference> Jumper Function JRTC CMOS Operating/Clear Setting JCFSEL Compact Flash Address Setting JCSEL1 Setting RS232/422/485 .
P 4 L A U s e r ’ s M a n u a l H a r d w a r e S e t u p Connector Reference 15 2.3 <Connector Reference> 2.3.1 <Internal Connectors> Connector Function Remark CPU LGA775 CPU socket S t.
P4LA User ’s Manual Introduction CPU Installation 16 2.4 <CPU and Memory Setup> 2.4.1 <CPU inst allation> P4LA has a LGA775 CPU socket onboar d; please check follo wing steps to install the processor properly . Attention If P4LA need RMA, please Keep CPU socket cover on the CPU Socket.
P 4 L A U s e r ’ s M a n u a l H a r d w a r e S e t u p Memory Inst allation 17 2.4.2 <Memory inst allation> P4LA has Four 240-pin DDR 2 DIMM support up to 3GB of memory capacity . The memory frequency supports 400/533/667M Hz .Only Non-ECC memor y is supported.
P4LA User ’s Manual Introduction CMOS Setup 18 2.5 <CMOS Setup> The board’s data of CMOS can be setting in BIOS. If the board refus es to boot due to inappropriate CMOS setting s, here is how to proc eed to clear (reset) t he CMOS to its default values.
P 4 L A U s e r ’ s M a n u a l H a r d w a r e S e t u p Enhanced IDE Interface 19 2.6 <Enhanced IDE interface> The Intel ® ICH7R (south brid ge chip) supports one enh anced IDE interface, dual chan nel for two A T API devices with A T A100.
P4LA User ’s Manual Introduction Serial A T A Installation 20 2.7 <Serial A T A inst allation> P4LA has four Serial A T A II interfaces with RAID function, the transfer rate of the Serial A T A II can be up to 300MB/s. Please go to http://www .
P 4 L A U s e r ’ s M a n u a l H a r d w a r e S e t u p Floppy Inst allation 21 2.8 <Floppy Inst allation> P4LA has one 34-pin floppy i nterface, it suppor ts use floppy and po wering from onboard, please follow up the step s below to install the device.
P4LA User ’s Manual Introduction LA N Inst allation 22 2.9 <LAN inst allation> P4LA integrates one Gigabit LAN interfaces with Marvell E 8053; they provide a standar d IEEE 802.3 Ethernet interface for 1000BAS E-T , 100BASE-T X and 10BASE-T applications.
P 4 L A U s e r ’ s M a n u a l H a r d w a r e S e t u p A udio Inst allation 23 2.10 <Audio Inst allation> The board integrates onboard audio interface with REAL TEK ALC880 codec, with Intel next generation of audio standard as Hig h Definition A udio, it offers more vivid soun d and other advantages than former AC97 audio compliance.
P4LA User ’s Manual Introduction A udio Inst allation 24 Connector: CN_A UDIO Type: 10-pin (2 x 5) header (pitch = 2.00mm) Pin Description Pin Description 1 MIC_L 2 Ground 3 MIC_R 4 VCC 5 Front_R 6 MIC_JD 7 Sense 8 N/C 9 Front_L 10 Line_JD Connector: CDIN Type: 4-pin header (pitch = 2.
P 4 L A U s e r ’ s M a n u a l H a r d w a r e S e t u p Display Installation 25 2.1 1 <Display Inst allation> P4LA integrates with Intel ® 945G GMCH for Intel Graphic Media Accelerator (GMA) 950 technology . It supports Intel ® DVMT (Dynamic V ideo Memory T echnology) 3.
P4LA User ’s Manual Introduction USB Installation 26 2.12 <USB Inst allation> P4LA integrates eight USB2.0 ports. The s pecifications USB2.0 are listed below : Interface USB2.
P 4 L A U s e r ’ s M a n u a l H a r d w a r e S e t u p USB Installation 27 Connector: CN_USB1/2 Type: 10-pin (5 x 2) header for USB1/2 Ports Pin Description Pin Description 1 VCC 2 VCC 3 Data0- 4.
P4LA User ’s Manual Introduction Power and Fan Installa tion 28 2.13 <Power and Fan Installation> The P4LA provides a standard A TX po wer supply with 24-pin A TX connector and ad ditional 12V.
P 4 L A U s e r ’ s M a n u a l H a r d w a r e S e t u p Power and Fan Installa tion 29 Connector: AT X Type: 24-pin ATX power connector PIN assignment 1 3.3V 13 3.3V 2 3.3V 14 -12V 3 GND 15 GND 4 5V 16 PS_ON 5 GND 17 GND 6 5V 18 GND 7 GND 19 GND 8 PW_OK 20 -5V 9 5V_SB 21 5V 10 12V 22 5V 1 1 12V 23 5V 12 3.
P4LA User ’s Manual Introduction GPIO Interface 30 2.14 <GPIO interface> The board provides a programmable 8-bit di gital I/O interface, and a SMBus (System management bus) interface for control panel application. Connector: CN_DIO Type: onboard 2 x 6-pin header, pitch=2.
P 4 L A U s e r ’ s M a n u a l H a r d w a r e S e t u p Enhanced IDE Interface 31 2.15 <Serial Port> The board has one RS232 serial ports on real I/O panel, and five onboard serial port . COM2 Support RS232/422/485. Jump setting please refer to Page 57 This Pin header provide +5V/+12V for COM1/COM2 Pin1,Pin 9.
P4LA User ’s Manual Introduction Switch and Indicator 32 2.16 <Switch and Indicator> The JFRNT provides front con trol pane l of the boar d, such as pow er button, reset and beeper , etc. Please check well before you connecting the cables on the chassis.
P 4 L A U s e r ’ s M a n u a l H a r d w a r e S e t u p Expansion Interface 33 2.17 <Exp ansion Interface> P4LA has one 16x , 4x and 1x PCI-Expr ess slot .
P 4 L A U s e r ’ s M a n u a l 34 (This Page is Lef t for Blank).
P 4 L A U s e r ’ s M a n u a l S y s t e m C o n f i g u r a t i o n SA T A Configuration 35 Chapter 3 <System Configuration> 3.1 <SA T A configuration> Based on Intel ® ICH7R Southbridge chip, the boar d supports 4 Serial A T A II ports; please follow the touring guide to setup y our Serial A T A devices.
P 4 L A U s e r ’ s M a n u a l S y s t e m C o n f i g u r a t i o n SA T A Configuration 36 SA T A Mode: This option can let you select whether the Se rial A T A hard drives would work under normal IDE mode or RAID mode. The RAID mode need more than one HDD is applied.
P 4 L A U s e r ’ s M a n u a l S y s t e m C o n f i g u r a t i o n SA T A Configuration 37 On-Chip Serial A T A mode: This option can let you select operat ion modes of Serial A T A drives. Disabled: T o disable the onboard Serial A T A controller .
P 4 L A U s e r ’ s M a n u a l S y s t e m C o n f i g u r a t i o n SA T A RAID Configuration 38 3.2 <SA T A RAID Configuration> The board integrates Intel ® ICH7R with RAID function for Se.
P 4 L A U s e r ’ s M a n u a l S y s t e m C o n f i g u r a t i o n SA T A Configuration 39 Please press <CTRL+I> to enter the RAID configuration menu. Y ou can setup the RAID under operation s ystem for Microsoft ® Windows XP SP1 or Windows 2000 SP4 version, pleas e install the Intel ® Application Accelerat or V er .
P 4 L A U s e r ’ s M a n u a l S y s t e m C o n f i g u r a t i o n SA T A RAID Configuration 40 2. Select Actions to Create RAID V olume Rename the V olume name Select RAID Level as 0 Left as def.
P 4 L A U s e r ’ s M a n u a l S y s t e m C o n f i g u r a t i o n SA T A Configuration 41 3. Please select two hard drives to prep are to set the RAID volume 4. S pecify the V olume size T une this bar to specify the volume size, if y ou specify the v olume size lower than maximum, you can create a second volume for another RAID set.
P 4 L A U s e r ’ s M a n u a l S y s t e m C o n f i g u r a t i o n SA T A RAID Configuration 42 3.3 <Audio Configuration> The board integrates Intel ® I CH7R with REAL TEK ® ALC880 co dec. It can support 7.1 channel sound under system configurati on.
P 4 L A U s e r ’ s M a n u a l S y s t e m C o n f i g u r a t i o n Video Memory Setup 43 3.4 <V ideo Memory Setup> Based on Intel ® 945G chipset with GMA (Graphic Media Accelerator) 950, the boar d supports Intel ® DVMT (Dynamic Video Memory T echnol ogy) 3.
P 4 L A U s e r ’ s M a n u a l 44 System Memory On-Chip Frame Buffer Size Fixed Memory Size DVMT Memory Size To t a l Graphic Memory 1MB 32MB 0MB 32MB 1MB 0MB 32MB 32MB 8MB 32MB 0MB 32MB 128MB~255M.
P 4 L A U s e r ’ s M a n u a l S y s t e m C o n f i g u r a t i o n Display Properties Setting 45 3.5 <Display Properties Setting> Based on Intel 945G GMCH with GMA 950 (Graphi c Media Accelerator), the board supports two DACs for display device as different resolution and color bit.
P 4 L A U s e r ’ s M a n u a l S y s t e m C o n f i g u r a t i o n Display Properties Se tting 46 3. This setup options can let you define each device settings. Notice: The dual disp la y needs PCIE-SDVO module to s upport more than one dis pl ay devices.
P 4 L A U s e r ’ s M a n u a l B I O S S e t u p BIOS Setup 47 Chapter 4 <BIOS Setup> The motherboard uses the A ward BIOS fo r the system config uration. The Award BIOS in the single board computer is a cust omized version of the industrial standard BIOS for IBM PC AT-compatible computers.
P 4 L A U s e r ’ s M a n u a l S y s t e m C o n f i g u r a t i o n Display Properties Setting 48 (This Page is Lef t for Blank).
P4LA User ’ s Manual I/O Port Pin A ssignment I 49 Appendix A <I/O Port Pin Assignment> A.1 IDE Port 39 1 Connector: IDE1 Type: 40-pin (20 x 2) box header 40 2 Pin Description Pin Description .
L V -672 User ’ s Manual I/O Pin Assignment Floppy Port 50 A.3 <Floppy Port> 33 1 Connector: FDD Type: 34-pin (2 x 17) 2.54-pitch header Pin Description Pin Description 1 Ground 2 DRIVE DENSIT.
P4LA User ’ s Manual I/O Port Pin A ssignment I 51 A.5 <Serial Port> 1 2 3 4 5 6 7 8 9 Connector: COM1 Type: 9-pin D-sub male connector on I/O Panel Pin Description Pin Description 1 DCD 6 DSR.
P4LA User ’s Manual System Resources I/O Port A ddress Map 52 A.7 <LAN Port> Connector: RJ45 Type: RJ45 connector with LED on I/O Panel Pin 1 2 3 4 5 Description TRD0+ T RD0- T RD1+ TRD1- NC Pin 6 7 8 9 10 Description NC TRD2+ T RD2- TRD3+ T RD3- A.
P4LA User ’ s Manual I/O Port Pin A ssignment I 53 A.9 <LPT Port > Connector : LPT T ype :26-Pin D-Sub female Connector on I/O Panel Pin Description Pin Description 1 -PSTB 2 PRO0 3 PRO1 4 PRO.
P4LA User ’s Manual System Resources I/O Port A ddress Map 54 Appedix B <System Resources> B1.<I/O Port Address Map>.
P4LA User ’ s Manual I/O Port Pin A ssignment I 55.
P4LA User ’s Manual System Resources I/O Port A ddress Map 56 B2.<Memory Address Map>.
P4LA User ’ s Manual I/O Port Pin A ssignment I 57 B3.<System IRQ & DMA Resources> D M A : IRQ :.
P4LA User ’s Manual System Resources I/O Port A ddress Map 58 Appedix B <How to setting RS-422/485> JCSEL1 5 6 1 2 12 3 1 RS-232 JCSEL2 10 JCSEL1 JCSEL1 RS-485 RS-422 JCSEL2 JCSEL2.
P4LA User ’ s Manual I/O Port Pin A ssignment I 59 Appedix C <Flash BIOS> C.1 BIOS Auto Flash T ool The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below : ht t p: / /www.
P4LA User ’s Manual System Resources I/O Port A ddress Map 60 Appendix D <Programming GPIO’s> The GPIO can be programmed with the MSDOS debug program using simple IN/OUT com mands.The following lines show an example how to do this. GPIO0….
P 4 L A U s e r ’ s M a n u a l H a r d w a r e T e s t Programming GPIO’ s 61 Appendix E <What Dog timer Setting > The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as sy stem reset mode by program.
L V -674 User ’s Manual Con t act Information Conta ct Information 62 Contact Information Any advice or comment about our pr oducts and service, or anythi ng we can help you please don’t hesitate to cont act with us. W e will do our best to support you for your products, project s and business.
デバイスIntel P4LAの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Intel P4LAをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIntel P4LAの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Intel P4LAの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Intel P4LAで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Intel P4LAを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIntel P4LAの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Intel P4LAに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIntel P4LAデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。