Jet ToolsメーカーJWL-1440VSの使用説明書/サービス説明書
ページ先へ移動 of 32
Opera ting Instructions and Parts M anual 14 ” x 40 ” Woodturnin g Lathe Model JW L- 1440V S JET 427 New Sanf or d Road LaVergne, Tennessee 37086 Part No . M-719400 Ph.: 800-274-6848 Revi si on C 11 /2014 www.jet tool s.c o m Copyri ght © 2014 JET Show n wit h optiona l 20 - inch ext ension be d (#719401) This .
2 1.0 Warranty and Service JET wa rrants eve ry produc t it sel ls aga inst manu factu rers’ de fects. If one of ou r tools ne e ds se rvice o r re pair, please contact Te chnical Se rvice by calling 1-800-2 74-6846, 8AM to 5PM CST, M onday t hrough F r iday.
3 2.0 Table of cont ents S e c t i o n P a g e 1.0 Warranty and Service ............................................................................................................................... ...... 2 2.0 Table of contents ................
4 3.0 Saf ety warnings 1. R ead an d understand the entire own er’ s manu al bef ore attemptin g assembly or operation. 2. This wood lath e is designed and in te nded for use by proper ly trai n ed a nd ex per ienced pe rso nne l o nl y.
5 28. Do not attempt to engage th e spindle l ock pin until the spindle has s topped. If l eaving the mac h i n e area, t u rn lat h e off and wait un t il t h e spindl e stops before departi n g.
6 5.0 Speci f i cations M ode l nu mbe r .................................................................................................................. .................... JWL-1440VS Stock nu m bers : La the wi th Le g S e t .....................
7 Dim ensions: To ol res t .................................................................................................................... .......................1 2 ” (3 0 5 mm ) Le g foot prin t ...............................................
8 6.0 Setup and assembl y 6.1 Sh ipping con tents Car ton co n tents for # 719400K (see Figure 2) 1 Lathe bed wi th headstock, too l su ppo rt a n d tail s tock – A 2 Legs – B 1 Spin dle index pin.
9 4. I ns tal l l egs wi th ei gh t 5 /1 6 ” s cr ews , l oc k wash ers a nd flat washers (F ig ure 4), a nd 6mm he x ke y. 5. Tighte n screws f i rm ly. Figure 4 6. Install the four l e velers (Figure 5). Thes e ca n be adj u sted l ate r. Figure 5 7.
10 7.0 Electrical connections Electr ical conn ections must be made by a qualified electr ician in complian ce with all rele v a n t codes. This machine must be pr operly gr ounded to h elp prevent electrical shock and possible fatal in jury. The J W L-1440VS Lathe i s rated at 115/230V power, and is pre-w ired for 115 vol t.
11 Altern at ively, the lat h e m ay be “hard-wired” to the power s ource. If y ou are h ard-w i r in g the l ath e t o a pa n el, mak e s u r e a di s conn ec t is available f or the operator.
12 8.4 Cam tigh tness The clamping mechanis ms of h eadstock, tailstock and tool rest base are pre- set by t he manufact urer, an d should n ot require adjus tment. If one of them does n ot tig hten properly against the bed when the locki n g h a n dle is t i ghtened, adj us t it as follows.
13 3. Perf or m the desired procedure. 4. Un screw t he in de x pin unti l the spindle is released. Rotate spindle to next des i red hole, and repeat. Rem ov e spi n dl e index pi n before star tin g lat h e. IMP O RT ANT: D o no t us e i nd e x p i n t o l o c k sp i nd le , whi c h w ill cause unnece ss ary wear to t h e pi n .
14 8.13 Checkin g center ali gnm ent W h en the headstock is retur n ed from outboard position, t h e a li gnment between ce n ter s should be ch ecked. 1. Lock the h eadstock in n orm al s p indle t u r ning po sit ion. 2. S l ide the tailstock toward the h ead s tock until the centers almost to uch (see Figure 18).
15 4. Bed ways; keep clean , use steel wool to remove any rust spots, a nd apply paste wax to prevent buildup of rust a n d f inishes. 5. Tool rest; use a mi ll fil e to rem ove ni ck s and dings. 6. Spin d l e tapers; should be c l ea n a nd free of dust and chi ps f or proper seating of tapers.
16 10.4 Stock S elec tion St o ck fo r s pin dles sh oul d b e s tr ai gh t gr ain ed an d f ree o f checks , cracks, kn ot s and other defec ts . It should be cut 1/8" to 1/4" larger t han the fini sh ed diameter and m ay require addi t i onal l engt h s o t he ends can be removed later.
17 10.5 Cut ti ng Tec hniq ues 10. 5. 1 Roughing Out 1. B egin wi t h a large ro u ghi n g gouge. P lace the to ol on th e t o ol res t wi th th e h eel of t h e to ol on the surface to be cut. 2. S lowly a nd gently rai se tool handl e unti l cutting edge com es into contact with the workp i ece.
18 6. A dditi o nal cuts may be take n to add to e ither th e depth or width of the cut. 10. 5. 5 Parting Off 1. Use partin g tool. 2. A d j u st lathe s peed to l ower RP M f or partin g through a workpiece. 3. P lace tool on tool s upport and raise the handle un t il i t starts to c u t a n d continue to c u t toward center of workpiece.
19 10. 6. 3 Wood Selec tion Firewood is the ch eapest, m os t widely av a ilable stock to use w hile learning to t u rn bowl s . Simply waste wood f or a wh ile pract i c in g t u r ning techniques . Develop skill wit h eac h too l before attempting to make a f i nish ed p iece.
20 10. 7. 2 To Sh ape Int e r ior o f Bo wl 1. Stop lath e a n d m ov e tailstock away. (You may want to re move th e center from the tai lstock to avoid bumpin g it w ith y o ur elbow.) 2. A d j u st too l support in front of the bowl j us t below cen terl in e, at a rig h t a ngle to the lathe w ays.
21 11.0 Maintena nce B ef o r e d oi ng m ai nt e na nc e o n th e lathe, disco nn ect it from th e electr ical su ppl y by pulling out t h e pl u g or swi tch i ng off th e main switch.
22 13.0 Troublesho oting the J W L- 1440VS Lathe Table 3 Sym pto m Possible Cause Corr ection Motor f ai ls to deve l op f u l l power. P ow er li ne o ver loa ded . Co rre ct over lo ad c ond it io n. Undersi zed wire s in su ppl y system, or extensi on cord i s too lo n g.
23 14.0 Recom mended Lathe Speeds (per diamet er of workpi ec e) Diameter o f Work Roug hi ng RPM Gen eral C ut t ing RP M Fin i shing RPM Under 2” 1520 3000 3000 2” t o 4” 760 1600 2290 4” t .
24 15.0 Indexer Positions How to use th e char t A diagram of the indexer is shown at right, as viewed from the tails t ock en d of the Lath e. Points A, B an d C are the holes in t h e h ead ca s ting. T h e holes in t h e spindle collar m ay be c onsidered a s numbered 1 th rough 12.
25 16.0 Replacem ent Parts Replacement parts are l isted on t h e f ol lowi n g page s. To order part s or reach our s ervice departm en t, call 1- 800-274-6848 Monday through Friday, 8:00 a.
26 16.1.2 JW L-1440V S Heads t ock A ssembly – Parts List Ind ex No. Part No. Descrip t ion Siz e Qty 1 ................ JML-3 ........................ Spu r Center ............................................................. MT2 ..................
27 Ind ex No. Part No. Descrip t ion Siz e Qty 61 .............. J W L1440-161 ............ Motor (i n c lude s #62) ................................................ ............. ......................... 1 .................. J W L1440-MF............
28 16.2.1 JW L-1440V S Bed A ssembly – E xploded View.
29 16.2.2 JW L-1440V S Bed A ssembly – P arts List Ind ex No. Part No. Descrip t ion Siz e Qty 1 ................ JE T-113..................... JET Nameplate ........................................................ ....... ..........................
30 16.3.1 JW L-1440V S Leg Se t – Exploded V iew 16.3.2 JW L-1440V S Leg Se t – Parts List Ind ex No. Part No. Descrip t ion Siz e Qty .................. 719402 ...................... JWL- 1440VS Leg Set (inclu des #1 t h r u 6) .............. ...
31 16.4.1 JW L-1440V S E xtension B ed A ssembly (OPTIONA L) – Exploded V iew 16.4.2 JW L-1440V S E xtension B ed A ssembly (OPTIONA L) – Parts List Ind ex No. Part No. Descrip t ion Siz e Qty .................. 719401 ...................... 20" E x te nsi o n Bed w/ Post (in c lu des #1 thr u 6) .
32 17.0 Electri cal Connections.
デバイスJet Tools JWL-1440VSの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Jet Tools JWL-1440VSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJet Tools JWL-1440VSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Jet Tools JWL-1440VSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Jet Tools JWL-1440VSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Jet Tools JWL-1440VSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJet Tools JWL-1440VSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Jet Tools JWL-1440VSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJet Tools JWL-1440VSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
