Jet ToolsメーカーJWL-1642EVSの使用説明書/サービス説明書
ページ先へ移動 of 27
OWNER'S M A NU A L JWL-1642EVS Wood Lathe WMH T OOL G RO UP Consumer / Light Industrial P r oducts Divi s i on P .O. B OX 1349 Auburn, WA 98071- 1349 Ph: 1- 800-274-6848 Fax: 1- 800- 274- 6840 E-m ail: j et@wmht oolgroup.com www . wmht oolgr oup.
2 Thi s manual has been prepared for t he ow ner and ope rat ors of a J W L- 1642EVS. It s purpose, aside from m achine operati on, i s to pr o m ot e saf ety through t he use of acc epted correct operati ng and maintenance procedur es .
3 WARNING 1. Read an d un d erstan d th e e n ti re owner’ s manual before at t emp ting assemb l y o r o p eration . 2. This wo od lathe is design ed and in tended for use by properl y trained and exp eri enced per sonne l on ly.
4 24. Chec k c ent ers and center socket s in t he headstoc k and t ailstoc k t o be s ure t hey are f ree of dirt or rust and oil li ghtl y befor e insert i ng cent ers. 25. T est each set-up by r ev olv i ng the w or k by hand t o i nsure i t c l ears the t ool rest and bed.
5 Grounding Ins truct ions Ca ution: This too l m ust be gr ounde d wh ile in use to protec t t he ope rator from elec tric s hoc k. In t he ev ent o f a m alfuncti on or breakdown, grounding prov ides a path o f least resistance for e l ectric curr ent to reduce the r i sk o f elect r i c shock.
6 Introduction The JET J WL-1642EVS l athe you hav e purchas ed is a hi gh quali ty tool that wi ll giv e you y ears of superi or serv ic e. Y ou will get maxim um perf ormance and enj oym ent fr om your new l at he if you w oul d take a f ew m om ents now to rev i ew the entir e m anual bef ore beginni ng ass em bl y and operati on.
7 Speci fi cati ons JW L-16 42EVS Stoc k Nu mber ................................................................................................................................ 708359 Over Bed .........................................................
8 WARNING Read an d un d erstan d th e e n ti re con t ents of thi s manual before at t emptin g assemb l y or oper ati on! Fai lu re to comply may cause seri ou s in ju ry! Contents of the S h ipping Containers 1. Lat he 1. T ailstoc k 1. Headstock 1.
9 3. Lif t the tail s t ock end of the lat he up f ar enough to sli de a f ew piec es o f scrap wood under the l eg, see Fi gur e 2. 4. Thr ead adjustable feet (A, Fig. 2) into st and leg ( B, Fi g. 2). There is a fl at spot on the shaft near the f oot that w i ll accomm odate a wrench.
10 Guard 1. Attac h guard to t he bracket by i nserti ng the rod and lifti ng up on the plunger ( A, Fig. 5). 2. Ther e are t wo detents t hat will hol d the guard i n pl ace. One is for turni ng and t he other i s for when you need the guard up and out of the way .
11 8. Headst o ck Faceplat e: (K, Fi g. 8) Used for t urni ng bow l s and plat es. There are a num ber o f screw holes f or mounti ng the workpi ece. T hread t he f acepl a t e onto the spi ndle i n a c l ockwise di rect i on, and tighte n two se t scr e w s.
12 S peed C hange 1. Disco nnect the machine from the power sou rce! 2. Loos e n the l ocki ng handl e (A, Fig. 1 1). 3. Lift up on t he tensioni ng handle (B, Fig. 1 1) to rem ove tension from the poly v-belt . Y ou can now posit ion the belt i n the desired speed range.
13 M ount ing W ork pi ece B etw een C enters Spi ndle turni ng t akes pl ace between the cent ers of the lat he. It requir es a spur center i n t he headstoc k and a liv e c ent er in the tail stock. 1. W ith a ruler locat e and mark the c enter on each end by going corner to cor ner, see Fi gure 13.
14 Sto ck Sel e ct i on Stoc k for spindles s h oul d be strai ght grai ned and f ree of check s, cracks, knot s and other def ects. It should be cut 1/ 8" to 1/4" lar ger than the fi nished diameter and m ay requir e add i tional lengt h to remov e ends if requir ed.
15 Cove s 1. Use a spindl e gouge. W ith the fl ute of the tool at 90 degr ees to w or kpiec e, t ouch the center o f the cutti ng edge t o the workpi ece and rol l in t owards t he bot tom of the c o v e. Stop at the b ottom; attempti ng to go up the opposi te side m ay cause the t ool t o catch.
16 Sanding & Finis h ing Leav ing cl ean cuts w ill r educe t he a m ount o f sanding requi red. Adj us t lathe to a fi n i shing speed, and begi n wit h f ine sandpaper (120 gr it or fi ner) . Coarser sandpaper w ill le a v e deep scratc hes t hat ar e diffic u l t to re m ov e, and dull cri sp detail s.
17 Face Plate or Chuck W hile fac eplat es are t he sim p l est, m ost r eliabl e m e t hod of hol ding a block of wood f or turni ng, chuck s c an also be used. A c huck i s not a requi re m ent but i s handy when w ork ing on more than one pi ece at a time.
18 To Sh ape Ou tsi de of Bow l 1. Odd shaped burl s , crotches and other ir regul ar shaped blanks requi re speci al preparat ion bef ore mounti ng i n a chuc k , or onto a f aceplate. Remove the bark , if ther e is any, f r o m what appears t o be t he center of the t op of workpi ece.
19 T o Sh a pe Int e r ior of Bo wl 1. Stop l athe and m ov e tailstock away. Rem o v e center fr o m t ailstock to prev ent bum pi ng it w i t h elbow. 2. Adj ust tool support i n f r ont of the bowl j ust below cent erl ine, at a right angl e to the lat he bed.
20 A djust ing C lam p ing M echani sm The cl amps are pre- set at the f ac t ory and shoul d not need any adj ustm ent. Howe v er , if adjust ment is needed rem ove the stud (A, Fig. 24). Loosen t he lock ing handle and sl ide t he headstoc k, tail stock or tool rest to the edge o f the bed and sl ightl y turn t he he x nut (B, F i g .
21 Tr oubleshooti ng Probl em Possi ble Cause Solu tion Exc essiv e Vibrati on. 1. Workpi ece w arped, out of round, has m aj or flaw, or was im pr operly prepar ed f or turni ng 2. Worn spindl e bearings 3. W orn belt 4. Motor m ount bol t or handle loose 5.
22 Stand a nd Be d A s sembly.
23 Parts List for the JWL-1642EVS Woodworking Lathe Stand a nd Be d A s sembly Index P art No. No. Descrip tion Siz e Qty. 1 .......... J W L1642-201 ............... I.D. Label ............................................... ..........................
24 H eadst ock A ssem bly.
25 Parts List for the JWL-1642EVS Woodworking Lathe H eadst ock A ssem bly Index P art No. No. Descrip tion Siz e Qty. 1 .......... J W L1642-101 ............... H eads t ock ............................................. ..............................
26 Index P art No. No. Descrip tion Siz e Qty. 49 ........ JW L1642-149 ............... Reta ining Was he r .................................. ............................................... 1 50 ........ JW L1442-121 ............... Brack et ........
27 Wi r ing Diagram.
デバイスJet Tools JWL-1642EVSの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Jet Tools JWL-1642EVSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJet Tools JWL-1642EVSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Jet Tools JWL-1642EVSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Jet Tools JWL-1642EVSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Jet Tools JWL-1642EVSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJet Tools JWL-1642EVSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Jet Tools JWL-1642EVSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJet Tools JWL-1642EVSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
