Johnson HardwareメーカーE-16の使用説明書/サービス説明書
ページ先へ移動 of 25
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 1 – Section I JOHNSON VERTICAL BAND SAWS INSTRUCTION MANUAL AND PARTS LIST SECTION I – Manual FOR MODELS E-16 V-16 V-24 VH-24 V-40 V H - 4 0 N MA.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 2 – Section I If machine is to be operated At 440 volt 3 phase power, please read the following warning. FOREWORD These instructions cover the installation and operation of vertical band saws. Attention to maintenance and service will afford many year s of trouble free operati on.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 3 – Section I SECTION I - TABLE OF CONTENTS Specifications ......... .................. ...................... .............. ........................ 4 Machine Features ............... ............
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 4 – Section I SPECIFICATIONS Model Number: V-16 V-24/VH-24 V-40/VH-40 Capacity: Throat Inches 16 23-1/2 41 Work Height Inches 11 12-1/2 12-1/2 Tabl.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 5 – Section I.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 6 – Section I.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 7 – Section I MACHINE UNPACKING AND INSTALLATION UNLOADING: Remove the shrink-wrap covering the machine, carefully as not to damage painted surfaces, electrical or hydraulic parts. Carefully inspect the machine for physical damage.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 8 – Section I FILLING THE SPEED REGULATOR 1. Turn the saw on. 2. Screw the handwheel in. 3. Turn the saw off once handwheel is in. 4. Remove the mounting screws (item 6). 5. Remove the plug from the cylinder (Item 3).
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 9 – Section I WHEEL ALIGNMENT V-16 & V / VH-24 Note: This alignment is factory set, but may need adjustment when replacing blade. Two wheel machines have a bottom wheel that drives the saw blade and a top idle wheel that is adjustable to facilitate blade tracking.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 10 – Section I BLADE TENSIONING The blade indicator is located inside the upper wheel compartment, on the lower left side of the idle wheel. (See machine features graphic) The indicator has an arrow mounted on the horizontal plane, with a corresponding scale for blade tensioning.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 11 – Section I An analysis of the work to be performed should be made and the proper blade selected.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 12 – Section I HIGH SPEED ROLLER GUIDES Applications and Advantages: Friction and abrasive cutting, filing operations, al uminum and woodcutting. These guides eliminate having to change inserts when changing to blades of different widths.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 13 – Section I 4: Insert the mounting stud (B) into the guide casting (A). Keep the stud flush with the front of the casting. Keeping the mounting stud flat area on the bottom, tighten securely the set screw (C) on the bottom of the casting.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 14 – Section I Repeat this process for the lower guide assembly. Note: Upper guide stud may be adjusted in or out in the guide post to allow proper clearance for blade, and for alignment with lower guide.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 15 – Section I Note: Occasionally the drive wheel may have to be jogged by hand to engage the transmission lever.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 16 – Section I SAW BLADE SELECTION M AT ER I AL S H AP E M AT ER I AL S H AP E M AT ER I AL S H AP E MATERIAL IN INCHES TOOTH SELECTION TOOTH SELECTION TOOTH SELECTION 0 14 / 18 14 / 18 14 / 18 .1 14 / 18 14 / 18 14 / 18 .
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 17 – Section I MATERIAL ALLOY 1/2" 1" 2" 4" 7" 12" 1100,2011,2017, 2024 fpm 568 sipm 7 fpm 577 sipm 11 fpm 536 sipm 1.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 18 – Section I MATERIAL ALLOY 1/2" 1" 2" 4" 7" 12" A-6 fpm 227 sipm 3 fpm 223 sipm 4 fpm 214 sipm 6 fpm 199 sipm 9 fp.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 19 – Section I NITRONIC 50,60 fpm 68 sipm 1 fpm 67 sipm 1 fpm 64 sipm 2 fpm 60 sipm 3 fpm 54 sipm 3 fpm 47 sipm 3 MATERIAL ALLOY 1/2" 1" .
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 20 – Section I MATERIAL ALLOY 1/2" 1" 2" 4" 7" 12" INCONEL 751,X75 0 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79 sipm 1 fpm 79.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 21 – Section I 38 353 40% HYDRAULIC FEED TABLE Machines equipped with a hydraulic feed table (VH models) have a pumping unit in the base. Th e system has an adjustable relief valve, which is factory preset at 400 p.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 22 – Section I Cut the blade ends accurately and at right angles. (See graphic below) Check abutment against the stop for a cut at right angles. Proper welding can only be achieved if the blade ends are cut with out a burr and at right angles.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 23 – Section I After welding loosen the pressure clamps (7 fig. 1) and set the jaws to the wide annealing positio n by turning the upsetting pressure switch (2 fig. 1) counter clockwise. Re-clamp the blade so that the weld is in the center between the jaws.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 24 – Section I If incoming voltage is high reverse this procedure. If incoming voltage is low, the welder transformer has taps that can be set to a 10% in crease or decrease. SHOCK HAZARD! ONLY A QUALIFIED ELECTRICIAN SHOULD ATTEMPT T HIS.
4/29/03 Manual V-16, V-24, VH-24, V-40 & VH-40 25 – Section I RIP FENCE Standard all models (figure 2) (Part number 714805 – Model 24/40) (Part number 714869 – Model 16) Used for cutting material in accurate straight lines. To attach, insert T-bolt provided in the T-slot in the front of the table.
デバイスJohnson Hardware E-16の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Johnson Hardware E-16をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJohnson Hardware E-16の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Johnson Hardware E-16の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Johnson Hardware E-16で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Johnson Hardware E-16を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJohnson Hardware E-16の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Johnson Hardware E-16に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJohnson Hardware E-16デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。