Kawasakiメーカー840076の使用説明書/サービス説明書
ページ先へ移動 of 19
MODEL #840076 FOR CUSTOMER SERVICE POUR LE SERVICE APRÉS VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1-800-590-3723 Printed in China 87-1904-60957 KAW ASAKI™ IS A TRADEMARK LICENSED BY KA WASAKI™ MOTORS CORP ., U.S.A., WHICH DOES NOT MANUF ACTURE OR DISTRIBUTE THIS PRODUCT .
SECTION FOUR TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-30 MAINTENANCE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 ACCESSORIES . . . . . . . . . . . . . . . . . . . .
GENERAL SAFETY RULES – FOR ALL ELECTRIC POWER TOOLS READ AND UNDERST AND ALL INSTRUCTIONS. Failure to follow all instruc- ti on s li st e d b el o w m ay r es ul t in e le ct ri c sh oc k , f ir e an d/ o r serious personal injur y . KEEP GUARDS IN PLACE AND IN WORKING ORDER.
This metal cutting band saw is equipped with a grounded 3-wire power cord with a 3-prong plug. If the power cord will not fit into the wall plug, an approved adapter can be used as long as it is connected to the center screw in the wall plate.
KEEP BYST ANDERS, CHILDREN, AND VISITORS at a safe distance from the horizontal band saw while it is in operation. Distractions can cause inadvertent misuse resulting in possible injury to the bystanders or to the operator .
EXTREME CARE SHOULD BE T AKEN WHEN THE BAND SAW IS IN THE VERTI- CAL POSITION. It is important to keep hands away from the moving blade both above and below the work table. A sudden slip could bring hands in contact with the moving blade possibly resulting in severe injuries to the operator .
SYMBOLS IMPORT ANT : Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer .
6. Repeat this step for the remaining three legs. 7. Position the floor stand handle in the holes on the front legs. Adjust the legs slightly so the handle will fit. 8. Using two 1/2" (12 mm) box-end wrenches, place one on the hex nut on the inside of the attached leg and one on the outside hex screw head.
1. Set the metal cutting band saw upright on the leg set. 2. Slide the vise hand wheel onto the vise adjusting shaft on the front end of the band saw base. 3. Securely tighten the setscrew on the hand wheel locking it on the shaft. 4. Ensure the setscrew is tightened against the flat part of the adjusting rod.
18 Ch ec k t o e ns ur e t here are n o pa rt s o f t he fl at -h ea d s cr ew s ra is ed abo ve the ver tic al tab le wo rk sur fac e. Edg es of the sc re ws pro tru di ng ab ov e th e wor k su rfac e cou ld dam age w or kp ie ce s or ca use i rr eg ul ar cut s.
INCREASE BLADE TENSION 2. Loosen the hex head screw BEFORE adjusting the setscrew. 3. T urn the setscrew simultaneously with the adjustment knob making the blade track properly against the shoulder of the pulley . 4. After adjusting the setscrew , tighten the hex head screw.
LASER SAFETY NEVER LOOK INTO THE LASER BEAM. Any contact with the eyes by the beam could cause injur y . Do not use the laser when cutting reflective materials. DO NOT AIM THE LASER BEAM A T ANYONE OR A T REFLECTIVE SURFACES. CLASS 2M LASER PRODUCT . Any contact with the eyes by the beam could cause injury .
OPERA TING THE MET AL CUTTING BAND SAW The Kawasaki™ Metal Cutting Band saw can be operated in two modes: horizontal cutting and vertical cutting. The horizontal cutting is for larger or thicker workpieces while the vertical cutting table is generally used for smaller lightweight workpieces or workpieces requiring bevel cuts.
10. T o set the vise for angled cuts, loosen the two screws on the front vise plate. A gauge mounted on the side of the saw base will line up with the vise plate indicating the angle of cut. 11. For precise angle cutting, open the vise all the way and place a protractor or other precise measuring gauge against the vise plate.
CUTTING CURVES The blade on the metal cutting band saw does not turn from side-to-side to create scrolling effects. Cutting curved corners is achieved by making relief cuts along the curved path. The relief cuts allow the blade to make the cut without twisting.
TROUBLE PROBABLE CAUSE SOLUTION 30 TROUBLE PROBABLE CAUSE SOLUTION 29 Excessive Blade Breakage 1. Workpiece loose in vise 2. Incorrect feeding speed 3. Blade spacing to far apart 4. Workpiece too coarse 5. Blade tension incorrect 6. T eeth contacting work- piece before saw starts 7.
If you must use an extension cord, be sure that the gauge is large enough to carry the amount of current necessar y for your power tool. If not, your tool may experi- ence a loss of power , excessive voltage drop or overheating. The smaller the gauge number , the heavier the cord (see table below).
Warranty Performance By pur chasing the product, purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replace.
ALL TRADE AND/OR ITS REPRESENT A TIVE(S), OR THE PURCHASER, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANT ABILITY AND THE W ARR ANT Y OF FITN ESS FOR A P AR TICUL AR PURPO SE, ARE HERE BY EXP RES SL Y EXCLUDED AND DISCLAIMED BY ALL TRADE AND/OR ITS REPRESENT A TIVES.
デバイスKawasaki 840076の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Kawasaki 840076をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKawasaki 840076の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kawasaki 840076の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kawasaki 840076で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kawasaki 840076を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKawasaki 840076の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kawasaki 840076に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKawasaki 840076デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。