KohlerメーカーK341の使用説明書/サービス説明書
ページ先へ移動 of 16
OWNER’S MANUAL MODELS ’ K241/ K301 (10 hP) (12 hp) K321,& K341 (14 hp) operating & maintenance instructions (16 hP) Congratulations - You have selected a fine four-cycle, single cylinder, air-cooled engine. Kohler designs long life strength and on-the-job durability into each engine.
Safety Precautions I To insure safe operations please read the following statements and understand their meaning. Also refer to your equipment owner’s manual for other important safety information. This manual contains safety precautions which are explained below.
Safety Precautions (Cont.) A WARNING 3 @ l $5 St 0 : F Accidental Starts can cause Carbon Monoxide can cause severe injury or death. severe nausea, fainting or death.
Air Filter Ignition Coil Blowe !r ,HOUSI Air lnta Screen *NOTE: Dipstick or oil fill plug is optional and may vary depending on engine specification. I Cooling Shrouds Spark Plug Carbur / ‘etor / Oil Drain Oil Pan Figure 1. Typical Command Horizontal Shaft Engine.
Fuel Recommendations A WARNING: Explosive Fuel! Gasoline is extremely flammable and its vapors can explode if ignited. Store gasoline only in approved containers, in well ventilated, unoccupied buildings, away from sparks or flames.
Cold Weather Starting Hints 1. Be sure to use the proper oil for the temperature expected. See Figure 2 on page 4. 2. Declutch all possible external loads. 3. Set speed control at part throttle position. 4. A warm battery has much more starting capacity than a cold battery.
Angle of Operation This engine will operate continuously at angles up to 30°. Check oil level to assure crankcase oil level is at the ‘IF” mark. Refer to the operating instructions of the equipment this engine powers. Because of equipment design or application, there may be more stringent restrictions regarding the angle of operation.
Check Oil Level The importance of checking and maintaining the proper oil level in the crankcase cannot be overemphasized. Check oil BEFORE EACH USE as follows: 1. Make sure the engine is stopped, level, and is For a new engine, change oil after the first 5 hours cool so the oil has had time to drain into the of operation.
Wing Nut Air Filter Precleaner Figure 6. Air Cleaner Housing Components. Check the air cleaner daily or before starting the engine. Check for buildup of dirt and debris around the air cleaner system. Keep this area clean. Also check for loose or damaged components.
3. Check gap using a wire feeler gauge. Spark plug gaps are as follows: Battery/Breakerless . . . . . . . . . . . . . . .035” Magneto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 025” Gaseous Fuel Engines . . . . . . . . . ,018” (Magneto/Battery Only) Adjust the gap as necessary by carefully bending the ground electrode.
l Make sure fuel is reaching the carburetor. This includes checking the fuel lines and fuel pump for restrictions or faulty components, replace as necessary. l Make sure the air cleaner element is clean and all air cleaner element components are fastened securely.
Walbro Carburetor Adjustment In general, turning the adjusting needles in (clockwise) decreases the supply of fuel to the carburetor. This gives a leaner fuel-to-air mixture. Turning the adjusting needles out (counterclockwise) increases the supply of fuel to the carburetor.
6. Low Idle Fuel Needle Setting: Turn the adjusting needle in (clockwise). The engine speed may increase, then it will decrease as the needle is turned in (lean). Note the position of the needle. Back the needle out approximately l/8 to l/4 turn. See Figure 11 for best low idle fuel performance.
Storage If the engine will be out of service for two months or more, use the following storage procedure: 1 . 2 . Clean the exterior surfaces of the engine. Change the oil and filter while the engine is still warm from operation. See “Change Oil” on page 8.
Specifications Model: ................................................................................... K241 ................. K301 ................ K321 ................... K341 Bore: ................................................. inches (millimeters) .
ENGINE DIVISION, KOHLER CO., KOHLER, WISCONSIN 53044 FOR SALES AND SERVICE INFORMATION IN U.S. AND CANADA, CALL I-800-544-2444 FORM NO.: TP-1346-C ISSUED: 1 O/87 REVISED: 8197 MAILED: LITHO IN U.
デバイスKohler K341の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Kohler K341をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKohler K341の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kohler K341の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kohler K341で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kohler K341を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKohler K341の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kohler K341に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKohler K341デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。