Kustomメーカー36 coupeの使用説明書/サービス説明書
ページ先へ移動 of 28
.
.
T able of Contents Introduction..........................................................................2 Safety Information.................................................................4 Amp Specifications........................................
Congratulations! 2 Introduction “IS IT REALL Y THA T SIMPLE?” you ask. YES . When an amp has tone this hot, looks this cool and Vibe out the wazoo, it’ s bound to happen. Y ou are now a hipper person than before. Y ou look better , you seem smarter and you’ve probably even become more popular .
The Coupe is a one-of-a-kind amplifier in a sea of retreads . It has a special look that recaptures the flash of VINT AGE 1960s and ‘70s Kustom amps but with the T one that players often dream about, but don’t often attain. We’re talking about hot , chunky , su st ai ni ng sounds that will remind you why you play guitar in the first place.
4 Safety Information.
5 Safety Information.
6 Safety Information.
7 Safety Information.
8 Amp Specifications Model 36 Coupe All T ube guitar amp Power Amp T ubes 2-6L6GC power tubes using AUTOKRUISE™ biasing scheme Preamp T ubes 4-12AX7 preamp tubes(2 preamp, 1 effects loop, 1 phase in.
9 Amp Specifications Model 72 Coupe All T ube guitar amp Power Amp T ubes 4-6L6GC power tubes using AUTOKRUISE™ biasing scheme Preamp T ubes 4-12AX7 preamp tubes(2 preamp, 1 effects loop, 1 phase in.
10 Amp Specifications Model 72 Coupe Hardtop All T ube guitar amp head Power Amp T ubes 4-6L6GC power tubes using AUTOKRUISE™ biasing scheme Preamp T ubes 4-12AX7 preamp tubes(2 preamp, 1 effects lo.
.
’36 Coupe Front P anel 1) Input 1 —This 1⁄4” input jack provides the highest gain through the amp. It is considered to be the “normal” input. 2) Input 2 —This 1⁄4” input jack provides 6dB lower gain through the amp, so it will allow for a cleaner sound.
8) Lead V olume/Pull Bright —The Lead V olume control adjusts the gain at the input of the amplifier when the Lead channel is active. It is used in conjunction with the Lead Master to adjust the amount of distortion and volume for the channel. For cleaner sounds, this control would be set to lower settings and the Master set higher .
’36 Coupe Back 1) Footswitch —The Footswitch jack on the Coupe is a stereo jack that connects the Coupe footswitch to the amplifier . It uses a special circuit to decode the three switches through a simple stereo cable. In an emer - gency , a mono instrument cable can be used to allow footswitching of the channels only .
.
’72 Coupe Front P anel 1) Input 1 —This 1⁄4” input jack provides the highest gain through the amp. It is considered to be the “normal” input. 2) Input 2 —This 1⁄4” input jack provides 6dB lower gain through the amp, so it will allow for a cleaner sound.
lower settings and the Master set higher . For slight breakup, the controls would be set in their middle ranges. For heavier distortion, set the Lead V olume higher and the Master lower . Pulling the Pull Bright will increase the high frequencies of the signal, while also reducing low frequencies for a chunkier , tighter attack.
’72 Coupe Back 1) Footswitch Assignment —This button selects which of the amp’ s ef - fects are controlled by the “Effects” button on the footswitch. If the switch is IN, the footswitch will control the Reverb and the T remolo will only be controlled by the Pull Active Switch on the Speed control.
’72 Coupe Bottom 1) Power Cord Receptacle/Fuse Holder: Insert the AC cord (provided) firmly into the AC connector . NOTE: Replace the AC power cord if protective jacket is damaged or ground pin is damaged or removed. The fuse is located in a housing just below the re- ceptacle.
20 ’72 Coupe Hardtop Fr ont Panel 1) Input 1 —This 1⁄4” input jack provides the highest gain through the amp. It is considered to be the “normal” input. 2) Input 2 —This 1⁄4” input jack provides 6dB lower gain through the amp, so it will allow for a cleaner sound.
21 lower settings and the Master set higher . For slight breakup, the controls would be set in their middle ranges. For heavier distortion, set the Lead V olume higher and the Master lower . Pulling the Pull Bright will increase the high frequencies of the signal, while also reducing low frequencies for a chunkier , tighter attack.
22 ’72 Coupe Hardtop Back 1) Effects Send —This 1⁄4” jack delivers a tube-driven preamp signal to ex- ternal effects devices. It can be used to send the signal to another amplifier to run multiple amps. Connecting a 1⁄4” plug does NOT break the flow of the amplifier signal.
23 9) Impedance Selector —This switch is used to select the appropriate impedance, and is important in achieving the desired results from the Coupe amplifiers.
Coupe Footswitch 1) LEAD —The Lead footswitch selects between Rhythm and Lead Chan- nels on the amplifier , regardless of the setting of the channel selector switch on the front panel. If the LEAD word is backlit, then the Lead chan- nel is active.
.
Kustom Amplification • Cincinnati, OH, USA • WWW .KUSTOM.COM.
デバイスKustom 36 coupeの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Kustom 36 coupeをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKustom 36 coupeの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kustom 36 coupeの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kustom 36 coupeで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kustom 36 coupeを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKustom 36 coupeの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kustom 36 coupeに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKustom 36 coupeデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
