Lennox HearthメーカーLSVFSD-24の使用説明書/サービス説明書
ページ先へ移動 of 20
Report No.116-L-49-5 I N S T A L L A T I O N A N D O P E R A T I O N I N S T R U C T I O N S V ent-Free Millivolt Dual-Listed Gas Log Sets Shadowdance™ Series P/N 85005 1M R ev .
2 IM PO R T A NT S AFE TY A ND W AR NI NG IN FO RM A T IO N REA D TH IS M ANUA L IN ITS ENTI RETY AND UNDE R- ST AN D TH ESE RULES TO FOLL OW F OR SA FETY .
3 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE. These Gas Log Appliances incorporate unitized ceramic fiber logs which provides some glow realistically when the appliance is operating. The gas log sets covered in this document are heater rated units.
4 Adhere to all local codes or in their absence the latest edition of The National Fuel Gas Code ANSI Z223.1 or NFPA 54-latest edition which can be obtained from The American National Standards Institute, Inc. (1430 Broadway , New Y ork, NY , 10018) or National Fire Protection Association, Inc.
5 This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and venti lation air.
6 Not e: Illustrations shown in this manual reflect “typical” installations with nominal dimensions and are for reference only . Actual installations may vary due to individual design preferences. However , always main- tain minimum clearances to combustible materials and do not violate any specific installation requirements.
NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE. 7 Figure 3 Step 2. Ceiling Clearance: The ceiling must be at least 42" from the top of the appliance opening ( Figure 2 ) .
8 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE. Any outside air ducts and/or ash dumps in the fireplace shall be perma- nently closed at time of appliance installation. A qualified gas appliance installer must install this dual-listed appli - ance.
NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE. 9 The appliance gas inlet connection is 3/8" NPT at the regulator/valve, located on the left side facing the appliance. If a right side connection is requ ired, the conn ection pip e may be pipe d under the rear of the appli ance to end at the left hand side for connection to the inlet.
10 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE. LOG PLACEMENT INSTRUCTIONS 1. Place rear ember bed as shown in Figure 11 . Figure 11 - Install Rear Ember Bed 2. Place rear log onto the two rear grate locating pins as shown in Figure 12 (the locating pins are outlined in Figure 11 ).
11 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE. 7. Place the right top log onto rear log locating pin and the right front log locating pin as shown in Figure 17 . Right T op Log Locating Pins 8. Pla ce Lef t T op T wig (24 " and 30" mod els only ) ont o cor resp ondin g notch on rear log as shown in Figure 18A .
12 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE. T op Burner Air Shutter Adjustment Procedure 1. If you ha ve blue flame or the top bur ner is no t carry ing ove r and bu rning on all ports , the air shutter may need to be adjusted to 1/8 " gap for bot h Natu ral a nd Pro pane gas.
NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE. 13 1. Appliance operation may be controlled through the ON/OFF unit rocker switch, located in the bottom front of the appliance or through an optional remote control . 2. When lit for the first time, the appliance will emit an odor for an hour or two.
NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE. 14 (ref form #750127M) (ref form #750129M) Standard Remote Control System (Model RCL) The Model RCL (Standard) Remote Control System, features a simplistic on/off control function for the fireplace.
NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE. 15 (ref form #750252M) (ref form #750010M) ACCESSORY COMPONENTS (CONTINUED) * Fo r use with g as tra in mode ls LSV FSD-NG and L SVFSD-L P only 18" Gas Log Set 24" Gas Log Set Charred Ember Kit* Cat.
NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE. 16 * For the purpose of input adjustment. PILOT (O.D.S.) ASSEMBLY THERMOPILE WHITE WHITE WHITE RED MILLIVOL T VAL VE ON/OFF SWITCH PILOT PIEZO IGNITER IGNITION WIRE OFF ON OPTIONAL REMOTE CONTROL (MILLIVOL T) Vented/Unvented Gas Log Appliance T echnical Chart For Millivolt Log Set Model No.
17 4. Depress gas control knob slightly and turn clockwise to “OFF .” Do not for ce. 5. Close lower control compartment. LIGHTING INSTRUCTIONS – MILLIVOL T WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTL Y , A FIRE OR EXPLOSION MA Y RESUL T CAUSING PROPERTY DAMAGE, PERSONAL INJUR Y OR LOSS OF LIFE.
18 VENTED/UNVENTED TROUBLESHOOTING GUIDE OBSERVED PROBLEM POSSIBLE CAUSE REMEDY 1. When igniter button is pressed, there is no spark at ODS/pilot. A. Igniter electrode positioned wrong. Replace igniter . B. Igniter electrode broken. Replace igniter . C.
19 NOTE: DIAGRAMS AND ILLUSTRA TIONS ARE NOT TO SCALE. REPLACEMENT P ARTS LIST (MILLIVOL T) - SHADOWDANCE™ SERIES Replacement Parts List (Millivolt) - Shadowdance™ Series, Models LSVFSD-NG and LSVFSD-LP (18" and 24") No. Description Catalog Number 1.
20 Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information.
デバイスLennox Hearth LSVFSD-24の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Lennox Hearth LSVFSD-24をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLennox Hearth LSVFSD-24の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lennox Hearth LSVFSD-24の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lennox Hearth LSVFSD-24で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lennox Hearth LSVFSD-24を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLennox Hearth LSVFSD-24の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lennox Hearth LSVFSD-24に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLennox Hearth LSVFSD-24デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
