Lennox HearthメーカーS160の使用説明書/サービス説明書
ページ先へ移動 of 32
INST ALLA TION AND OPERA TION MANUAL W ARNINGS • Hot! Do not touch! The glass and surfaces of this appliance will be hot during operation and will retain heat for a while after shutting off the appliance. Severe burns may result. • Carefully supervise children in the same room as appliance.
2 CONGRA TULA TIONS! When you purchased your new wood stove, you joined the ranks of thousands of individuals whose answer to their home heating needs reflects their concern for aesthetics, efficiency and our environment. We extend our continued support to help you achieve the maximum benefit and enjoyment available from your new wood stove.
3 1. When this room heater is not properly installed, a house fire may result. T o reduce the risk of fire, follow the instal- lation instructions. Contact local building or fire officials about restrictions and installation inspection requirements in your area.
4 This manual describes the installation and operation of these non-catalytic wood heaters. These heaters meet the U.S. Environmental Protection Agency’ s emissions limits for wood heaters sold on or after July 1, 1990.
5 This appliance is not designed to be operated in a negative pressure. In very airtight homes with large kitchen exhaust fans, furnace cold air returns, fresh air exchange systems and any other air system in close proximity to the heating appliance may create a negative pressure in the same room as the heating appliance.
6 WA RNING: BE ABSOLUTE L Y SURE THE DIST ANCE BETWEEN THE HEA TER AND THE SURFACE OF ANY COMBUSTIBLE CONSTRUC- TION IS NOT LESS THAN SHOWN IN THE FIGURES ON P AGE 7. Floor Protection USA - The floor in front and under the heater must be protected with noncombustible material.
7 Diagram B: Side View-Alcove & Parallel Installation Diagram A: T op View-Parallel Installation K B A E C D *L K Floor Protection Floor Protection Floor Protection G G F F 72" Min.
8 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Shown with T ubinox™ Stainless Steel Liner components (see Page 28 for ordering information) Chimney T ermination Cap Chimney T ermination Rai.
9 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Manufactured Home Installations (ref. Figure 7 ) This appliance is approved for installation into a manufactured (mobile) home in the USA ONL Y!.
10 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Chimney Connector Systems and Clearances from Combustible Walls for Residential Heating Appliances (NFPA 211) Refer to Figure 8 System A. Minimum 3.5 in. (90 mm) thick brick masonr y wall framed into combustible wall with a minimum of 12 in.
11 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Figure 10 Figure 9 T o install the “Outside Air Kit,” position the clip so that the nut is directly above the hole punched in the back of the heatshield (See Figure 11 ) .
12 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 14. All horizontal runs of pipe should be as short as possible and are requ ired by NFP A No. 211 to have an upwar d pitch or rise in the same direction the smoke travels of no less than 1/4” to the linear foot.
13 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 5. If required, install the Outside Air Kit (cat. no. 71112) as per the following instructions. T o locate the hole in the hearth for outside air mark and cut a 4” (102 mm) hole in the hearth.
14 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 1. Check that all chimney pipe joints are securely fastened. 2. Check that the heater is securely fastened to the floor (if ap- plicable). 3. Make sure the intake vent has clear access to outside air (if ap- plicable).
15 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Brick Sizes A = 4-1/4” x 9” B = 2-1/4” x 8-7/8” D = 2-1/4” x 9” E = 1-1/2” x 8-7/8” F = Full Brick (4-1/2” x 9”) G = 1-1/2” x 9” Figure 14 3. Next, you will install the baffle blanket.
16 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Be sure to clean plated accessories with a household type cleaner and a ver y soft cloth to remove any fingerprints and residues prior to the first fire. 1. NEVER USE FLAMMABLE LIQUIDS TO ST ART OR REKINDLE A SOLID FUEL FIRE!! 2.
17 W ARNINGS The blower must be plugged directly into a properly grou nded three- pron g rece ptac le, 120 V AC, 60 Hz, single phase. Do not cut or remove the grounding prong from this plug. Do not route power cord under or in front of appliance. Installation must be in accordance with National Elec- trical Code, ANSI/NFP A 70 - latest edition.
18 It is important to know that for high, combustion efficient, clean burns, you will need to have sufficient temperatures inside the firebox for thorough combustion . The best method for determining if you have sufficient temperatures is to watch the brick lining in your firebox.
19 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. DOOR HINGES: If door hinges need lubricating, use an anti-seize com- pound (never use oil) available from your Lennox Hearth Products dealer .
20 Problem Solution POOR DRAFT : Extend chimney in length or have the chimney realigned to the proper size flue. Oversized chimneys normally have poor drafts. Remember , the stoves’ draft depend solely on the natural draft of the chimney (See Draft Requirements on Page 4 ).
21 DO NOT : Install or operate this stove before reading this manual. DO NOT : Close the draft beyond the point at which the flames are completely extinguished. DO NOT : Open the stove door without fully opening the draft first. DO NOT : Burn driftwood or wood that has been in salt water .
22 FRONT DOOR P ARTS LIST Item # Ca t. N o De scr i pt ion 1 H5639 Door Rope Kit, 7/8” Dia. (6’ 2”) 2 H5629 Upper Hinge Pin 3 H5626 Upper Hinge Pin E-Clip 4 H5628 Lower Hinge Pin 6 H5640 Glass G.
23 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. REPLACEMENT P AR TS - MODELS S160 AND SWS160.
24 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. REPLACEMENT P AR TS - MODELS S160 AND SWS160 Door Parts Blower Parts 7 13 1 2 3 4 5 6 8 1 2 3 4 5 9 10 8 14 11 6 7 12 25 29 31 28 27 26 32 30.
25 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. REPLACEMENT P AR TS - MODELS S160 AND SWS160 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE.
26 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. REPLACEMENT P AR TS - MODELS S160 AND SWS160 15 18 15 18 19 16 17 19 Ash Drawer Pedestal and Pedestal.
27 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Product Reference Information Cat. No. Description Ship. Weight Ship. Volume H 7 8 8 4 S1 60 T -B , S to v e / T ra di ti o n a l B l a c k D o o r / N i c k e l N a m e p l at e 3 1 3 l b . 1 8 .
28 ACCESSORIES - MODELS S160 AND SWS160 Secure Black™ Single Wall Stove Pipe 6” SW Pipe and Accessories Cat. No. Model Description Pc. / Container 6SWL6 6SWL6 LENGTH 6” X 6” 100 6SWL12 6SWL12 .
29 ACCESSORIES - MODELS S160 AND SWS160 Secure T emp® Factory-Built Chimney 6” Secure T emp ASHT and Secure T emp G-ASHT Cat. No. Model Description Pc.
30 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. SAFETY / LISTING LABEL - ENGLISH 2011 2012 2013.
31 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. SAFETY / LISTING LABEL - FRENCH.
32 Y our Appliance’ s Model Number _______________________________________ Y our Appliance’ s Serial Number ________________________________________ The Date On Which Y our Appliance Was Installed.
デバイスLennox Hearth S160の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Lennox Hearth S160をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLennox Hearth S160の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lennox Hearth S160の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lennox Hearth S160で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lennox Hearth S160を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLennox Hearth S160の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lennox Hearth S160に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLennox Hearth S160デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
