Lowrance electronicメーカーMARK 5X PROの使用説明書/サービス説明書
ページ先へ移動 of 28
Installation & Operation manual Elite 5X, Mark 5X, Mark 5X Pr o & Elite 4X Operation manual.
Cop yright © 2011 Navico All rights reserved. Lowranc e ® and Navic o ® ar e registered trademarks of Navico . Navico ma y nd it necessary to change or end our policies, regulations and special oers at an y time. W e reserve the right to do so without notice .
1 T able of Contents Introduction ...................................... 2 Basic Operation ............................... 3 Setup wizard ............................................ 3 Working with menus ................................ 4 Fishing Mode .
2 Introduction Getting Started T urn unit on/off T o turn on/of f the unit, press and hold the LIGHT/ POWER key for three seconds. Adjusting the backlight This unit has 10 backlight levels. Press the LIGHT/ POWER key to switch backlight levels. Muting Audio Select Mute Audio from the System menu and press ENTER .
3 Basic Operation Setup wizard The Setup wizard will appear when the unit is turned on for the rst time. T o choose your own settings, do not run the setup wizard .
4 Basic Operation On/Off features Select an on/o menu item and press ENTER to turn it on/o . Dropdown menus After accessing the dropdo wn menu, press the keypad up/ down to select the desired item and press ENTER . Accessing menu items The keypad and ENTER key are used to select menu items and open submenus.
5 Basic Operation T o input text: 1. Use the keypad to select the desired character and press ENTER . 2. Repeat Step 1 for each character . 3. When entry is completed, highlight OK and press ENTER .
6 Basic Operation Advanced Mode Enables advanced fea tures and settings. The follo wing features are enabled when A dvanced mode is turned on: • Colorline (manual control) • Surface Clarity (manua.
7 Basic Operation Standby mode Low ers power consumption by turning o sonar and the display . Pr ess the PWR/LIGHT key to ac- cess the Backlight menu. Select Standby and press ENTER . Pr ess any key to resume normal op- eration. Restore defaults Resets unit options and settings to defaults.
8 Pages Sonar Page Displays the wat er column moving from right to left on your unit’ s screen. On the right side of the screen, the Amplitude Scope bar preview s echoes about to appear on the display .
9 Pages Overlay Data Displays selected overla y data on the sonar page. Show Enables/disables the display of overla y data, allow- ing you to r emove overlay data fr om the screen without deleting the selected overlay data con- guration. Congure Used to select overlay data t o be displayed on the screen.
10 Pages T o select overlay data: 1. From the sonar page, press MENU . 2. Select Overlay data and press ENTER . 3. Select Congure and press ENTER . 4. Press Menu and select Add . Press ENTER . 5. Select the desired data from the Con- gure Items to show screen.
11 Sonar Move the blue sonar history bar all the way to the right to resume normal sonar scrolling . Pr ess MENU and select Exit cursor mode to re - move the cursor fr om the screen. Sonar Menu The sonar menu has options and settings that aect the appearance of the display .
12 Sonar Pr ess MENU from any sonar page to access the So- nar menu. Adjust (Advanced Mode only) Used to make adjustments to Sensitivity, C olorline and Grayline. Sonar Menu (Advanced Mode) Sensitivity Controls the level of detail shown on the display .
13 Sonar Mark series units have a monochrome display , so wide bands of gray indicat e a hard sonar return, while softer returns are shown as dark, narrow areas . Auto Sensitivity Keeps sensitivity at a level that works w ell under most conditions, r educing the needs for adjust- ments.
14 Sonar Split Flasher Split Zoom Frequency Contr ols the transducer frequency used by the unit. This unit supports t w o frequencies: 200kHz and 83kHz. 200 kHz has the highest sensitivity and best tar- get discrimination in shallow water . 83 kH z o ers a wider cone angle for mor e water cover age.
15 Sonar Fish ID Displays sh echoes as sh sym- bols instead of sh arches . Fish ID is not the most accurate method of sh detection since structure and suspended debris may be shown as a sh symbol on the display .
16 Sonar Overlay Data Allows y ou to selec t data (w a- ter temperatur e, depth, etc) to be displayed on t op of the Sonar screen. Overlay data setup is cov ered in the P ages sec tion.
17 Settings Settings Menu Accesses t o installation and conguration settings for your unit . System Adjusts unit settings like language, mut e audio and advanced mode.
18 Settings Set Language Selects the language used on menus and text box es. Mute Audio T urns on/o unit audio, like key beeps , alarm sounds, etc . Advanced Mode Enables featur es and settings only available with unit in Advanced Mode . Restore Defaults Switches the unit back to default settings.
19 Settings Sonar Used to make adjustments t o Sonar options and display settings like Noise Rejection, Sur face and F ishing Mode. Noise Rejection Uses advanced signal processing to monitor the ef- fects noise (boat pumps, wat er conditions, engine ignition systems , etc.
20 Settings Installation Pr ovides access to Keel Oset and T emp Calibration settings. Keel Offset All transducers measure w ater depth from the transducer to the bottom. A s a result, water depth readings do not accoun t for the distance from the transducer to the keel or fr om the transducer to the water surface.
21 Settings Before setting keel o set, measure the distance from the transducer t o the lowest part of the keel. If, f or example, the keel is 3.5 feet belo w the trans- ducer , it will be input as –3.
22 Index A About 18 Advanced Mode 6 Alarms 21 F ish 21 Shallow 21 Amplitude Scope 15 Auto Sensitivity 13 C Color 15 Colorline 12 Cursor 6 Custom Range 13 D Depth Range 13 Dialogs 5 Dropdown menus 4 F .
Specications Elite 5x, Mark 5x & Mark 5x Pro General Case size 5.4” H (134mm) x 6.8” W (174mm); 6” H (152mm) with bracket Display Mark : (5” diagonal) High-contrast lm Supertwist LCD.
Specications Elite 4x General Case size 5.6” H (144mm) x 3.7” W (94.3mm); 6.4” H (164mm) with bracket Display (3.5” diagonal) 320x240 (256 color) TFT L CD Backlight White LED (10 levels) Power T ransmit power 2100W PTP; 262W RMS Power requirement 12V V oltage input 10 to 17V Current drain at 13.
How to Obtain Service… …in the USA: Contact the F actor y Cust omer Ser vice Department. Call toll-free: 800-324-1356 8 a.m. to 5 p .m. Central Standard Time, M-F Navico may nd it necessary to change or end shipping policies, regulations and special oers at any time .
© Copyright 2011 All Rights Reser ved Navico Holding AS *988-10157-001* Visit our w ebsite: w w w .lo wranc e.c om.
デバイスLowrance electronic MARK 5X PROの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Lowrance electronic MARK 5X PROをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLowrance electronic MARK 5X PROの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lowrance electronic MARK 5X PROの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lowrance electronic MARK 5X PROで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lowrance electronic MARK 5X PROを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLowrance electronic MARK 5X PROの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lowrance electronic MARK 5X PROに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLowrance electronic MARK 5X PROデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。