Makitaメーカー2702X1の使用説明書/サービス説明書
ページ先へ移動 of 28
With Electric Brake 210 mm (8-1/4”) MODEL 2702X1 MODEL 2702 255 mm (10”) MODEL 2703X1 MODEL 2703 T able Saw www .makita.com INSTRUCTION MANUAL DOUBLE INSULA TION W ARNING: For your personal safety , READ and UNDERST AND before using. SA VE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
2 MODEL Arbor hole Blade diameter Cutting capacities 90 ° 45 ° T able size (W x L) No load speed (RPM) Dimensions (L x W x H) Maximum dado capacity Net weight 18kg (40 lbs) 4,600/min 560mm x 686mm x.
3 9. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed; for example, don’t use circular saw for cutting tree limbs or logs. 10. WEAR PROPER APP AREL. Wear no loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts.
4 16. REDUCE THE RISK OF UNINTENTIONAL ST ARTING. Make sure switch is in off position before plugging in. 17. USE RECOMMENDED ACCES- SORIES. Consult the owner ’s manual for recom- mended accessories. The use of improper accessories may cause risk of injury to persons.
5 1. Wear eye protection. 2. Don ’ t use the tool in presence of flam- mable liquids or gases. 3. NEVER use the tool with an abrasive cut-off wheel installed. 4. Check the blade carefully for cracks or damage before operation. Replace cracked or damaged blade immediately .
6 18. Do not perform any operation freehand. Freehand means using your hands to sup- port or guide the workpiece, in lieu of a rip fence or miter gauge. 19. NEVER reach around or over saw blade. NEVER reach for a workpiece until the saw blade has completely stopped.
The tool is shipped from the factory with the saw blade and blade guard not in the installed condition. Assemble as follows: CAUTION: • Always unplug the tool before assembly . Installing saw blade Remove the table insert on the table. Hold the outer flange with the offset wrench and loosen the hex nut counterclockwise with the wrench.
8 Installing blade guar d CAUTION: • Before installing the blade guard, adjust the depth of cut to its maximum elevation. Insert the spreader between the blade guard mounting portion (stay) and the pressure plate. T ighten the hex bolts (A) with the offset wrench.
9 P ositioning table saw Locate the table saw in a well lit and level area where you can maintain good footing and balance. It should be installed in an area that leaves enough room to easi- ly handle the size of your workpieces.
10 Adjusting depth of cut The depth of cut may be adjusted by turning the han- dle. T urn the handle clockwise to raise the blade or counterclockwise to lower it. NOTE: • Use a shallow depth setting when cutting thin materi- als in order to obtain a cleaner cut.
After adjusting the positive stops, set the blade at 90 ° to the table surface. Then adjust the arrow pointer so that its right edge is aligned to the 0 ° graduation. Installing and adjusting rip fence Raise the grip of the rip fence. Install the rip fence on the table so that the fence holder engages with the guide rail.
12 CAUTION: • Always grasp the striped portion of the wrench when tightening the hex bolts. If you tighten the hex bolts while grasping the wrench further than the striped por- tion, the hex bolts may be damaged and/or an injury to your hand may result.
When operating the switch lever , it is convenient to view it through the window area in the table. CAUTION: • When not using the tool, remove the key and store it in a secure place.
14 Push stick A push stick can be easily made from a piece of ply- wood 19 mm (3/4 ” ) to 25 mm (1 ” ) thick. Cut out the hatched area on the stick and smooth edges with a file. (H) dimension should be less than 12.7 mm (1/2 ” ) so as to be thinner than the workpiece.
W ood facing (rip fence) A wood facing should be used for operations when the blade comes close to the rip fence. Wood facing for the rip fence should be the same size as the rip fence. Make sure the bottom of facing is flush with the table surface. Crosscutting CAUTION: • When making a crosscut, remove the rip fence from the table.
16 A uxiliary wood facing (miter gauge) T o prevent a long board from wobbling, fit the miter gauge with an auxiliary fence board. Fasten with bolts/nuts after drilling holes, but fasteners must not protrude from the face board. Ripping CAUTION: • When ripping, remove the miter gauge from the table.
3. T urn the tool on and gently feed the workpiece into the blade along with the rip fence. (1) When the width of rip is 150 mm (6 ” ) and wider , carefully use your right hand to feed the work- piece. Use your left hand to hold the workpiece in position against the rip fence.
CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Cleaning Clean out sawdust and chips from time to time. Carefully clean the blade guard and moving parts inside the table saw .
19 CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated pur- pose.
T able insert (Part No. 317061-6) When cutting grooves 5/16 ” , 3/8 ” ,7/16 ” or 1/2 ” use this table insert instead of the standard table insert. T o install the dado head set, proceed as follows: 1. T urn the tool off and unplug it before installing.
21 NOTE: • When widths slightly greater than the above are required, fit the paper washers in between the inside and outside cutters to adjust the width. 5. Arrange the cutters so that the tips of the inside cut- ters are positioned at the gullets of the outside cutter .
Featherboards are used to keep the workpiece in con- tact with the rip fence and table as shown, and to stop kickbacks. T o install featherboards, proceed as follows: 1. T urn the tool off and unplug it. 2. Add 8 ” high flat facing board to the rip fence, the full length of the rip fence.
23 How to perf orm rabbeting 1. Remove blade guard. 2. Attach auxiliary fence to rip fence for cuts that run the length of the stock. Facing should be as high as the workpiece is wide. Adjust fence and blade to desired dimensions. 3. First cut: Hold board flat on table as in ordinary rip- ping.
24 CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
21 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut.
22 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2.
2 7 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ALABAMA 2365 Pelham P arkway Pelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadw ay Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd.
W ARNING Some dust created by po wer sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th defects or other reproductiv e har m.
デバイスMakita 2702X1の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Makita 2702X1をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMakita 2702X1の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Makita 2702X1の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Makita 2702X1で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Makita 2702X1を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMakita 2702X1の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Makita 2702X1に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMakita 2702X1デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
