Makitaメーカー5630DWAの使用説明書/サービス説明書
ページ先へ移動 of 20
Cordless Circular Saw Blade Cutting depth No load speed Overall 45" iRPMi length 2,600 diameter 90" 165 mm 0 54" 0- 38" 364 mm (6- 1 /2") 10 ~ 2-1/8") 10 ~ 1-1/2") (.
GENERAL SAFETY RULES (For All Battery Operated Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit.
Tool Use and Care Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. *Do not force tool. Use the correct tool for your application.
Specific Safety Rules 1. DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade. Keep your body positioned to either side of the saw blade, but not in line with the saw blade.
11. Causes and Operator Prevention of Kickback: Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the opera tor.
Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK.
15. Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As examples, Fig. 5 illustrates the RIGHT way to cut off the end of a board, and Fig. 6 the WRONG way.
SYMBOLS The followings show the symbols used for tool. ...... volts ................................. amperes ................................. herts ................................. kilograms hours ................................. minutes .........
IMPORTANT SAFETY INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord FOR CHARGER & 25 50 100 150 18 18 18 16 BATTERY CARTRIDGE 1. SAVE THESE INSTRUCTIONS - This manual 9.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (50OFI 2. Do not attempt to use a step-up transformer, an engine generator or DC power or ABOVE 4OoC (104OF). receptacle. 3.
Installing or removing battery cartridge *Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge.
*If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools.
Hex wrench storage When not in use, the conveniently stored. hex wrench can be CAUTIO N: Always be sure that the tool is switched off and the battery cartridge is removed before any adjustment is attempted. Adjusting depth of cut Loosen the lever on the depth guide and move the base up or down.
CAUTION: After adjusting the depth of cut and bevel cutting angle, be sure to tighten the screw. Sighting The front of the base is notched to provide two guide edges. For straight cuts, align the edge with 0" engraved on it with your cutting line on the workpiece.
Operation Hold the tool firmly. Set the base plate on the workpiece to be cut without the blade making any contact. Then turn the tool on and wait until the blade attains full speed. Now simply move the tool forward over the workpiece surface, keeping it flat and advancing smoothly until the sawing is completed.
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes reg- ularly. Replace when they wear down to the limit mark.
Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. N i-Cd Tungsten carbide tipped saw blade Part No For wood To recycle the battery: 1. Remove the battery from the tool. 2.
Feb-04--'99 US CORDLESS CIRCULAR SAW Model 5630DW e- 59 Note: The switch and other part ConfigUratlOnS may differ from country to Country. 18.
MODEL 5630DW Feb-04-'99 US MACHINE ~ 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 21 28 29 30 I:"," GtD DESCRIPTION 16 21 31 41 51 61 71 81 91 1 1 2 2 2 1 1 1 1 3 2 1 1 1 1 1 1 1 .
I 1 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy I Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
デバイスMakita 5630DWAの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Makita 5630DWAをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMakita 5630DWAの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Makita 5630DWAの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Makita 5630DWAで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Makita 5630DWAを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMakita 5630DWAの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Makita 5630DWAに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMakita 5630DWAデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。