Mantisメーカー"E" Systemの使用説明書/サービス説明書
ページ先へ移動 of 14
© 2006 Mantis, Div . of Schiller -Pfeiffer Inc. All Rights Reserved. Edger “E” System Owner s Manual and Saf ety Instr uctions.
1 T able of Contents Important Information A. Introduction This attachment is fitted with a blade, intended to be used to edge flower beds, sidewalks, driveways, curbs, etc. B. Specification. C. Contents of the package 1. Edge T rimmer Attachment Assembly 2.
2 Safety and W arnings A. Safety Decals Please pay particular attention to the warning and information decals found on various parts of this Edger Attachment unit. They are an important part of the safety system. These decals must be replaced in time due to abrasion, etc.
3 General Safety Rules 1. Never edge while people, especially children or pets are nearby . 2. Before using, always visually inspect to see that the blade, blade bolts and cutter assembly are not worn or damaged. 3. Do not start the motor when a bystander is standing in front of the blade.
Length (feet) 1 to 25 26 to 50 51 to 100 101 to 150 Cord gauge (A WG) 18 16 14 12 4 b. Based on the total length of cord that you are going to use, check the chart to make sure the cord meets the correct minimum cord gauge (A WG) requirements.
5 W ARNING – DANGER IMPROPER ASSEMBL Y OF THIS EQUIPMENT CAN RESUL T IN SERIOUS INJUR Y . MAKE SURE TO FOLLOW ALL INSTRUCTIONS CAREFULL Y . IF YOU HA VE ANY QUESTIONS, CONT ACT MANTIS CUSTOMER SER VICE. 34. Always disconnect power cord from power source: a.
6 T ools: 9 / 16 " wrench, pin supplied with the unit or screwdriver 1. Remove the following parts from the Edge T rimmer Assembly: blade mounting bolt #1 by rotating it clockwise, clamping plate #2, gear case cover #3, holding screws #4, and cover #5.
7 Check the balance of the assembled unit. The handles and shoulder harness have been assembled at the factory and set according to the average sized person.
8 T ools: 9 / 16 " wrench, pin or screwdriver 1. Lock the gear shaft by inserting the pin or screwdriver through the aligned keyholes in the gear case cover and the gear case to prevent rotation (Picture 19).
9 1. Clean. 2. Lubricate for rust prevention. 3. Store indoor . Storage 1. W ith both hands on the handles, push lockout trigger button with your thumb first, and then squeeze trigger . Start edging when blade rotates at full RPM, by lowering the blade gently into the ground.
10 Service Maintenance Guide Area Maintenance procedure Frequency Spline male/female connection of the inner drive shaft Inspect/Lubricate 1. Remove the side screw , and loosen up other three as shown on the diagram (left). 2. Pull the shaft from the gear housing.
11 1 2 3 4 6 5 7 8 20 11 12 24 25 9 10 13 14 15 16 23 22 18 19 21 26 31 29 28 30 32 27 42 39 41 40 34 33 35 36 37 38 44 43 49 58 48 47 46 51 54 55 56 57 53 52 56 45 50 62 60 61 59 63 1 7 Edger “E”.
KEY # DESCRIPTION P ART # QTY 1 GEAR CASE ASSEMBL Y 331 137 1 2 GEAR CASE 331 138 1 3 O-RING 331 139 1 4 BEARING 6201Z 331 140 1 5 SEAL 331 141 1 6 RING RET AINING 331 142 1 7 SHAFT 331 143 1 8 GEAR 3.
Specifications, descriptions, and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice.
デバイスMantis "E" Systemの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Mantis "E" Systemをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMantis "E" Systemの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Mantis "E" Systemの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Mantis "E" Systemで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Mantis "E" Systemを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMantis "E" Systemの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Mantis "E" Systemに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMantis "E" Systemデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。