McIntoshメーカーMCC602TMの使用説明書/サービス説明書
ページ先へ移動 of 20
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New Y ork 13903-2699 Phone: 607-723-3512 F AX: 607-724-0549 Owner s Manual MCC602TM MCC602TM Power Amplifier.
2 IMPOR T ANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERA TING THIS EQUIPMENT . General: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. W arning: T o reduce risk of fir e or electrical shock, do not expose this equipment to rain or moisture.
3 Customer Service T echnical Assist ance Please T ake A Moment Thank Y ou Copyright 2000 ã by McIntosh Laboratory , Inc. The serial number , purchase date and McIntosh dealer name are important to you for possible insurance claim or future service.
4 Performance Features Introduction · Power Output The MCC602TM consists of two separate power amplifier channels, each capable of 300 watts into 2, 4 or 8 ohm loudspeakers with less than 0.
5 General Notes cont, Introduction, Performance Features and Dimensions The following dimensions can assist in determining the best location for your MCC602TM. There is additional in- formation on the next page pertaining to installing the MCC602TM into your vehicle.
6 Inst allation It is recommended that a professional who is skilled in all aspects of installation and operation install the MCC602TM and any associated mobile audio equipment. Amplifier V entilation Always provide adequate ventilation for the MCC602TM.
7 Installation, Side Panel Cooling, Connections, Controls and Switch Connect to the positve (+) vehicle battery terminal with an inline fuse Cooling Fan Air Intake Controls the Power Guard Circuit whe.
8 How to Connect for T wo Channels Left T weeter Left W oofer/Midrange 1. Connect the power control cable from the Control Cen- ter Amp ON to the MCC602TM ON Connector on the right side of the Amplifier . Note: All cables should be connected to the amplifier befor e connecting the DC power cables to the battery .
9 How to Connect for T wo Channels Right T weeter Right W oofer/Midrange Right Crossover Network (4 Ohms) Left Crossover Network (4 Ohms) V ehicle Battery + - Fuse.
10 How to Connect for Mono Parallel 1. Connect the Power Control Cable from the Control Center Amp ON to the MCC602TM ON connector on the right side of the amplifier . Note: All cables should be connected to the amplifier befor e connecting the DC power cables to the battery .
11 How to Connect for Mono Parallel V ehicle Battery + - Fuse W oofer (4 Ohm) W oofer (4 Ohm) + + - -.
12 CHANNEL 1 METER indicates the Channel 1 Power Output CHANNEL 1 POWER GUARD LED lights when the Power Guard Circuit activates for Amplifier Channel 1 CHANNEL 2 METER indicates the Channel 2 Power Ou.
13 The McIntosh MCC602TM is a highly versatile amplifier that can be configured in many ways. This manual gives examples of some of the most common configurations and will guide you through the basic operation, however we suggest you refer to your dealer for further information on the use of this unit.
14 How to Replace the Fuses How to Replace the Fuses If the MCC602TM produces no sound, no Meter Illumination, the power control and the power supply connections seem secure, one or more of the Amplifier Fuse(s) may have failed. Under normal operating conditions your amplifier s fuses should not fail.
15 T echnical Description McIntosh Laboratory , the company who introduced the world s first amplifier over fifty years ago that could be called High Fidelity, has done it again. The McIntosh engineering staf f has created a power amplifier without compromise, using the most advanced McIntosh circuit design concepts.
16 nel cooling fins. T emperature sensors, attached to the inte- rior of the tunnel, control the cooling fans. The fans are normally off; if the program material contains sustained loud passages demanding high power , the fans will turn on to increase cooling.
17 T echnical Description, cont Power Supply Figure 16 Figure 14 W ithout Power Guard Figure 15 W ith Power Guard Figure 13 Input T est Signal engineers know how to do it right. Protection Circuits The MCC602TM incorporates it s version of the McIntosh Sentry Monitor output transistor protec- tion circuit.
18 Specifications Specifications Power Output S tereo Minimum sine wave continuous average power output per channel, all channels operating is: 300 watts into 2 ohm load 300 watts into 4 ohm load 300 .
19 Packing Instructions Quantity Part Number Description 1 034140 Shipping carton only 2 034141 End cap (Foam pad) 1 034142 Center Support (Foam pad) Packing Instructions In the event it is necessary to repack the equipment for shipment, the equipment must be packed exactly as shown below , failure to do so will result in shipping damage.
McIntosh Part No. 040730 McIntosh Laboratory , Inc. 2 Chambers Street Binghamton, NY 13903.
デバイスMcIntosh MCC602TMの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
McIntosh MCC602TMをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMcIntosh MCC602TMの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。McIntosh MCC602TMの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。McIntosh MCC602TMで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
McIntosh MCC602TMを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMcIntosh MCC602TMの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、McIntosh MCC602TMに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMcIntosh MCC602TMデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。