Metra Electronicsメーカー99-7504の使用説明書/サービス説明書
ページ先へ移動 of 8
INST ALLA TION INSTRUCTIONS FOR PART 99-7504 99-7504 APPLICA TIONS Mazda 3 2004-2009 KIT FEA TURES • DIN Mount Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Bonus Display.
Dash Disassembly - M a z d a 3 2 0 0 4 - 2 0 0 9 ......................... . . . . . . . . 1 Kit Assembly - Display Brackets/Pocket Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - DIN Mount Radio Provision with Pocket . . . . . . . .
99-7504 DASH DISASSEMBL Y MAZDA 3 2004-2009 A CL O CK S ET LO A D FM1 /2 A M C D TA P E/ M D HOOK B REAR VI EW - DISPLA Y TRIM PA N EL C 1 D isconnect the negative battery ter- minal to prevent an accidental short circuit. 1 Unclip and remove display trim panel above radio .
99-7504 DISPLA Y/POCKET ASSEMBL Y DISPLA Y BRACKETS/POCKET ASSEMBL Y MAZDA 3 2004-2009 A B 2 Using the (2) 3/8” #10 bolts and (2) #10 nuts attach the display retention brackets to the display unit. 1 Using the (2) Phillips screws removed in step 4 of Dash Disassembly secure the display replacement pocket to the back of the display trim panel.
3 99-7504 KIT ASSEMBL Y A B C DIN MOUNT RADIO PROVISION Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 1 Slide the aftermarket radio unit into the cage and secure . (Figure B) 2 Snap the T rim plate into the Radio Housing.
99-7504 KIT ASSEMBL Y 4 A B ISO DIN MOUNT RADIO PROVISION Mount the ISO Brackets to the after- market radio using the screws sup- plied with the radio. (Figure A) 1 Slide the radio into the radio housing until it snaps into place . (Figure B) 2 Attach the trim plate supplied with the kit to the front of the radio hous- ing assembly .
Note: When inserting the 99-7504 into the sub dash be aware of the locations pointed out in Figure B . If the 99-7504 does not snap in correctly the result will be a noticeable gap on each side of the installation kit.
FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder , T a pe. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.
デバイスMetra Electronics 99-7504の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Metra Electronics 99-7504をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMetra Electronics 99-7504の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Metra Electronics 99-7504の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Metra Electronics 99-7504で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Metra Electronics 99-7504を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMetra Electronics 99-7504の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Metra Electronics 99-7504に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMetra Electronics 99-7504デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。