MicrosoftメーカーG7VP2の使用説明書/サービス説明書
ページ先へ移動 of 70
37310911 G7VP2 Re v . B+ System Board User s Manual.
Cop yright This publication contains information that is protected by copyright. No par t of it ma y be reproduced in an y form or b y any means or used to make any transformation/adaptation without the prior written per mission from the cop y right holder s.
FCC and DOC Statement on Class B This equipment has been tested and found to comply with the limits f or a Class B digital device , pur suant to Par t 15 of the FCC r ules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.
T able of Contents Chapter 1 - Introduction 1 . 1 Features and Specifications.................................................................................. 1 . 2 Package Checklist....................................................................
62 62 63 63 64 65 65 57 60 61 Chapter 4 - Supported Softwares 4 . 1 Desktop Management Interface.................................................................... 4 . 2 System Health Monitor Utility ..................................................
6 Introduction 1 1.1 Features and Specifications 1.1.1 Features Chipset VIA Apollo 598MVP A GP system chipset Processor The system board is equipped with a switching voltage regulator that suppor ts 2.0V to 3.5V core v oltage for various processor s .
7 1 Introduction Level 2 Cache Memory 512KB pipeline burst, direct map wr ite-back cache installed on the system board. Expansion Slots The system board is equipped with 1 dedicated PCI slot, 5 dedicated 16-bit ISA slots and 1 shared PCI/ISA slot.
8 Introduction 1 Bus mastering reduces CPU utilization during disk transfer Suppor t s A T API CD-R OM, LS-120, ZIP and SCSI sequential boot-up Ir D A Interface The system board is equipped with an IrD A connector for wireless connectivity between your computer and peripheral devices.
9 1 Introduction Dual Function P ow er Button (A TX power suppl y only) Depending on the setting in the BIOS setup, this switch will allow your system to enter the Soft-Off or Suspend mode.
10 Introduction 1 1.2 Package Checklist The system board package contains the following items: þ The system board þ A user s man ual þ Ser ial, mouse and printer por t cab les Option 1: - One ca.
11 2 Hardware Installation 2.1 System Board La yout square denotes pin 1 Chapter 2 - Hardware Installation.
12 2 Hardware Installation 2.2 System Memor y 2 . 3 DIP Switch and Jumper Settings of the Processors Make sure SW1 and JP5 are set correctly before applying power or you ma y damage the processor or system board. There are 10 switches on SW1. The black rectangle in the diagr am denotes the par t that is protr uding, the adjustab le switch.
13 2 Hardware Installation DIP Switch Settings for Intel Processors Intel Processors SW1: 1-6 90MHz - 60MHz - 1.5x 100MHz - 66MHz - 1.5x 120MHz - 60MHz - 2x 133MHz - 66MHz - 2x 150MHz - 60MHz - 2.5x 166MHz - 66MHz - 2.5x 200MHz - 66MHz - 3x MMX166MHz* - 66MHz - 2.
14 2 Hardware Installation DIP Switch Settings for IBM Processors IBM Processors SW1: 1-6 IBM Processors SW 1 : 1 - 6 6x86MX-PR200 - 66MHz - 2.5x 6x86MX-PR233 - 75MHz - 2.5x 6x86MX-PR266 - 83MHz - 2.5x 6x86MX-PR300 - 75MHz - 3x 6x86MX-PR333 - 83MHz - 3x 6x86MX-PR300 - 66MHz - 3.
15 2 Hardware Installation DIP Switch Settings fo r AMD Pr ocessors AMD Processors SW1: 1-6 AMD Processors SW1: 1-6 K6-200 - 66MHz - 3x K6-233 - 66MHz - 3.5x K6-266 - 66MHz - 4x K6-300 - 66MHz - 4.5x K6-2/250 - 100MHz - 2.5x K6-2/300 - 100MHz - 3x K6-2/266 - 66MHz - 4x K6-2/333 - 95MHz - 3.
16 2 Hardware Installation Frequency Ratio SW1: 4-6 1.5x / 3.5x Frequency Ratio SW1 : 4 -6 2x 2.5x 4x 4.5x 5x 3x 5.5x External System Bus Clock / Frequency Ratio - DIP Switch Settings If the processor.
17 2 Hardware Installation Frequency Ratio Settings for IDT Processors Frequency Ratio SW1 : 4-6 3.5x Frequency Ratio SW1 : 4 -6 2x / 3.3x 2.5x 4x 4.5x 2.
18 2 Hardware Installation DIP Switch and Jumper Settings for Cor e V oltage Voltage JP 5 SW1: 7-10 2.8V 2.0V 2.1V 2.9V 3.0V 3.1V Voltage JP5 SW1: 7-10 2.
19 2 Hardware Installation 2-3 On: Normal (default) 1-2 On: Clear CMOS Data 2.4 Jumper Settings for Clearing CMOS Data Jumper JP1 Clear CMOS Data If, for some reason, the CMOS data becomes corr upted, the system can be reconfigured with the default values stored in the ROM BIOS.
20 2 Hardware Installation 2 . 5 Jumper Settings f or Po w er Supply T ype Jumper JP2 P ow er Suppl y T ype The Baby A T form factor system board is designed to fit into an A TX fo r m factor chassis. It is equipped with A TX and A T po wer supply connector s.
21 2 Hardware Installation 2 . 6 Jumper Settings fo r A TX Po wer -On/Off Select (A TX power suppl y onl y) Jumper JPP A TX P o wer -On/Off Select Jumper JPP is used to select the method of powering-on/off a computer that is using an A TX po wer suppl y .
22 2 Hardware Installation 2.7 Jumper Settings for SDRAM Clock (DIMM) Jumper JP4 SDRAM Clock JP4 is used to set the SDRAM s clock according to the CPU clock or AG P clock. If y ou are using PC-100 SDRAM DIMMs, it is recommended that you set the SDRAM clock according to the CPU clock (2-3 On).
23 2 Hardware Installation 2 . 8 Jum p e r S e t t in g s f o r W atchdog T i m e r Jumper JP10 W atchdog Timer The system board suppor t s the W atchdog Timer function. It allows your application to regularly clear the system at the set time inter val.
24 2 Hardware Installation 2 . 9 Connecting the Ribbon Cables and Wires o f the Ports and Connectors 2.9.1 Serial Ports The b uilt-in serial por ts are RS-232C asynchronous comm unication por ts with 16C550A-compatible U ARTs that can be used with modems, ser ial printers, remote display terminals, and other serial devices.
25 2 Hardware Installation 2.9.2 K eyboar d Po rt/Connector The system board allows you to connect a standard A T keyboard b y connecting it to the standard A T keyboard por t or the 5-pin connector at location J14. A T keyboard por t J14 A T keyboard connector Pin 1 2 3 4 5 Function CLK Data N.
26 2 Hardware Installation 2.9.3 PS/2 Mouse Port The PS/2 mouse por t is a 6-pin connector on the system board. Attach the 6-pin mouse por t cable , which is mounted on a card- edge bracket, to connector J1. Make sure the red wire on the PS/2 mouse connector is aligned with pin 1 of connector J1.
27 2 Hardware Installation 2.9.5 Flopp y Disk Drive Contr oller 1 . Install the 34-pin header connector into the shrouded floppy disk header (J11) on the system board. Th e colored edge of the ribbon should be aligned with pin 1 of connector J11. 2 . Install the other 34-pin header connector(s) into the disk dr ive(s).
28 2 Hardware Installation 2.9.7 Universal Serial Bus Ports The system board is equipped with tw o header s , at locations J2 and J3 on the system board, for exter nal USB por ts . USB allo ws data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.
29 2 Hardware Installation Connecting the USB Ports As an option, one card-edge bracket mounted with tw o USB por t cab les may be pro vided with the system board. The ends of the cab les are attached to a connector . Connect the USB cable connector to J2 and J3 on the system board.
30 2 Hardware Installation 2.9.10 Chassis Fan Connector The system board is equipped with a chassis fan connector . If yo u are installing a fan in the system unit, connect the fan s connector to location J7 on the system board. The fan will provide adequate airflo w throughout the chassis to prev ent o verheating the processor .
31 2 Hardware Installation 2.9.11 J13 (LEDs and Switches) SP- LED - A TX 5VSB Standby LED This LED will light when the 5VSB power is active. AT X - S W - AT X P o w e r S w i t c h Depending on the setting in the BIOS setup , this switch is a dual function power button that will allow your system to enter the Soft- Off or Suspend mode.
32 2 Hardware Installation Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Pin Assignment SP-LED (ATX 5VSB Standby LED) ATX-SW (ATX power switch) HD-LED (Primary/Seconda.
33 2 Hardware Installation 2.9.12 Power Supply Connectors The pin assignment of the A TX power connector is shown belo w . Pin 1 2 3 4 5 6 7 8 9 10 Function 3.3V/14A 3.3V/14A Ground +5V Ground +5V Ground PW-OK 5VSB +12V Pin 11 12 13 14 15 16 17 18 19 20 Function 3.
34 3 Award BIOS Setup Utility 3 . 1 The Basic Input/Output System The Basic Input/Output System (BIOS) is a program that takes care of the basic level of communication between the processor and peripherals. In addition, the BIOS also contain codes for various advanced features found in this system board.
35 3 Award BIOS Setup Utility Date The date format is <day>, <month>, <date>, <year>. Day displays a da y , from Sunda y to Saturda y . Month displa ys the month, from Januar y to December . Date displays the date , from 1 to 31.
36 3 Award BIOS Setup Utility Driv e A and Drive B These categories identify the types of floppy disk drives installed. None No floppy drive is installed 360K, 5.25 in. 5-1/4 in. standard drive; 360KB capacity 1.2M, 5.25 in. 5-1/4 in. A T -type high-density dr ive; 1.
37 3 Award BIOS Setup Utility Memory The base memor y si z e , extended memor y size and the other memor y size cannot be altered; your computer automatically detects and displays them. Base Memor y The POST will determine the amount of base (or conv entional) memor y installed in the system.
38 3 Award BIOS Setup Utility 3.1.2 BIOS Features Setup The BIOS Features Setup allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others , if enabled, will improve the perfo r mance of your system or let you set some features according to your preference.
39 3 Award BIOS Setup Utility CPU Internal Cache and External Cache These categories speed up the memor y access. The default value is enabled. Enable the External Cache for better performance. Quick P ower On Sel f T est This categor y speeds up P ower On Self T est (POST) after y ou p o wer on y our system.
40 3 Award BIOS Setup Utility Memory ECC Function If y ou are using x72 (72-bit) DIMMs, which are DIMMs that suppor t the ECC (Error Checking and Correction) function, set this field to Enabled. T ypematic Rate Setting When disabled, continually holding down a key on your keyboard will cause the BIOS to repor t that the key is do wn.
41 3 Award BIOS Setup Utility OS Select for DRAM > 64MB This item allo ws you to access the memor y that is ov er 64MB in OS/2. The options are: Non-OS/2 and OS/2. HDD S.M.A.R.T . Capability The system board suppor ts SMAR T (Self-Monitoring, Analysis and Repor ting T echnology) hard dr ive s.
42 3 Award BIOS Setup Utility The settings on the screen are f or reference only . Y our v er sion ma y not be identical to this one. 3.1.3 Chipset Features Setup This section gives you functions to configure the system based on the specif ic features of the chipset.
43 3 Award BIOS Setup Utility System Health Monitor Note: The system board comes with a System Health Monitor utility . Once this utility is installed, the system will ignore the settings in the System Health Monitor field of the Chipset Features Setup .
44 3 Award BIOS Setup Utility 3.1.4 Power Management Setup The P ower Management Setup allo ws you to conf igure your system to most eff ectively save energy . If you like to use the soft power down feature of Windo ws 95/98, y ou must enab le the Po wer Management f ield belo w .
45 3 Award BIOS Setup Utility Power Management This categor y allows y ou to select the type (or degree) of power sa ving by changing the length of idle time that elapses before the Standby mode and Suspend mode are activated. Disable No power management.
46 3 Award BIOS Setup Utility Standby Mode This is user conf igur a b le only when the P ower Management categor y is set to User Def ined. When enabled and after the set time of system inactivity , the CPU clock will r un at a slower speed (1/3 of full speed) while all other devices still operate at full speed.
47 3 Award BIOS Setup Utility Resume On A lar m Enabled When Enab led, Date (of Month) and Timer (hh:mm:ss) will appear r ight below this f ield. Y ou can set the date and time y ou w ould like the Soft P ower Do wn (Soft-Off) PC to po wer -on.
48 3 Award BIOS Setup Utility Resources Controlled By The A ward Plug and Pla y BIOS has the capability to automaticall y configure all of the boot and Plug and Play compatible devices. Auto The system will automatically detect the settings for you. The categories that follow will not be shown on the screen.
49 3 Award BIOS Setup Utility PCI I RQ Activ ed By This categor y is used to set the method by which the PCI b us recogniz es that an IRQ ser vice is being requested b y a device . Under all circumstances, you should retain the default configuration unless a different setting is needed.
50 3 Award BIOS Setup Utility 3.1.8 Integrated Peripherals The settings on the screen are for re f erence only . Y our v ersion may not be identical to this one.
51 3 Award BIOS Setup Utility Onboard Primary PCI IDE and Onboard Secondary PCI IDE These categor ies allo w you to enable or disab le the primar y and secondary IDE controller . The default is Enabled. Select Disab led if yo u want to add a diff erent hard drive controller .
52 3 Award BIOS Setup Utility Auto The BIOS will automatically detect the settings for you. Disabled The BIOS will not detect these categories. USB Controller W e recommend that y ou leav e this f ield in its default setting - Enab led. USB K eyboard Support By default, this field is Disabled.
53 3 Award BIOS Setup Utility I R Duplex Mode Half Data is completely transmitted before receiving data. Full T ransmits and receiv es data sim ultaneousl y .
54 3 Award BIOS Setup Utility 3.1.9 Supervisor Password If y ou want to protect your system and setup from unauthorized entry , set a super visor s password with the System option selected in the BIOS Features Setup.
55 3 Award BIOS Setup Utility 3.1.11 IDE HDD Auto Detection Use this option to detect the parameter s for t he hard disk dr ives installed in y our system. These parameter s will then be automaticall y entered into the "Standard CMOS Setup".
56 3 Award BIOS Setup Utility 3.1.12 Save & Exit Setup When all the changes ha ve been made, highlight S a ve & Exit Setup and press <Enter>. The message below will appear : Save to CMOS and Exit (Y/N)? N T ype Y and press <Enter>.
57 4 Supported Softwares 4.1 Desktop Management Interface (DMI) The system board comes with a DMI built into the BIOS. DMI, along with the appropr iately networ k ed software , is designed to make in ventor y , maintenance and troubleshooting of computer systems easier .
58 4 Supported Softwares 4.1.2 Using the DMI Utility The four menus located on top of the DMI Configuration Utility screen are Edit DMI, Add DMI, Load DMI File and Sav e DMI File. Use the ← or → (left or right) arrow keys to select a menu from the Menu bar .
59 4 Supported Softwares Add DMI 1 . Use the ← or → ar row keys to select the Add DMI menu . 2. Highlight the item on the left screen that you would like to add by using the ↑ or ↓ arrow keys, then press <Enter>. 3 . The cur sor will move to the screen y ou select allowing you to enter information about the added item.
60 4 Supported Softwares 4.2 System Health Monitor Utility The system board comes with a System Health Monitor utility . This utility sho ws the cur rent temper ature of the processor , po we r voltages, and CPU/Chassis fan speed.
61 4 Supported Softwares Important: Once the utility is installed, the system will ignore the settings in the System Health Monitor field of the Chipset Features Setup . If you are using Windows 95/98 or Windows NT 4.0, you may select between using the utility and the Chipset Features Setup.
62 A Identifying Processors SXXXX/ RSS R (voltage range) V for VRE voltage range S for Standard voltage range SXXXX/ KLM K = V f o r VRE v oltage r ange, S for Standard v oltage range L = M for min va.
63 A Identifying Processors AMD-K6-233ANR K6 = Processor core 233 = P erf ormance r ating A = P ackage type: T ype A = CPGA B = Operating voltage: N: 3.1V -3.3V (core)/3.135V -3.6V (I/O) L: 2.755V -3.045V (core)/3.135V -3.6V (I/O) X = Case temperature W: 55 o C R: 70 o C Q: 65 o C Y: 75 o C X: 65 o C Z: 85 o C A .
64 A Identifying Processors A.5 IDT Processors C6-PSME200GA Product name Processor clock speed 3.52Vcc (66MHz clock) Processor voltage External system bus clock WinChip2-233 Product name Processor clock speed 3.
65 B System Error Message When the BIOS encounters an er ror that requires the user to correct something, either a beep code will sound or a message will be displa yed in a box in the middle of the screen and the message, PRESS F1 T O CONTINUE, CTRL-AL T -ESC or DEL T O ENTER SETUP , will be shown in the info rmation bo x at the bottom.
66 B System Error Message setting than indicated in Setup. Determine which setting is correct, either turn off the system and change the jumper or enter Setup and change the VIDEO selection. FLOPPY DISK(S) fail (80) Unable to reset floppy subsystem. FLOPPY DISK(S) fail (40) Floppy type mismatch.
67 C T roubleshooting C . 1 T r oubleshooting Checklist This chapter of the manual is designed to help you with problems that y ou may encounter with y our personal computer . T o efficientl y troub leshoot your system, treat each problem individuall y .
68 C T roubleshooting The picture seems to be constantly moving. 1 . The monitor has lost its v er tical sync. Adjust the monitor s ver tical sync. 2. Move away any objects, such as another monitor or fan, that ma y be creating a magnetic field around the display .
69 C T roubleshooting Hard Drive Hard disk failure. 1. Make sure the correct drive type for the hard disk drive has been entered in the BIOS. 2. If the system is configured with two hard drives, make sure the bootab le (fi r st) hard drive is configured as Master and the second hard drive is configured as Slav e .
70 C T roubleshooting Serial Port The serial de vice (modem, printer) doesn t output anything or is outputting garbled characters. 1 . Mak e sure that the ser ial device s po wer is tur ned on and that the device is on-line. 2 . V er ify that the device is plugged into the cor rect serial por t on the rear of the computer .
デバイスMicrosoft G7VP2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Microsoft G7VP2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMicrosoft G7VP2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Microsoft G7VP2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Microsoft G7VP2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Microsoft G7VP2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMicrosoft G7VP2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Microsoft G7VP2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMicrosoft G7VP2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。