MieleメーカーCS1212の使用説明書/サービス説明書
ページ先へ移動 of 48
Operating and Installation Instructions Ceramic combiset with Induction CS 1212 CS 1221 To prevent accidents and machine damage, read the Operating Manual before installation or use.
IMPORTANT SAFETY INSTRUCTIONS .................................4 Description of the unit ..............................................9 CS 1212 ..........................................................9 CS 1221 ......................................
SAFETY INSTRUCTIONS FOR INSTALLATION .........................3 0 Installation ......................................................3 3 Installation dimensions .............................................3 4 CS 1212 .................................
WARNING- When using your appliance follow basic precautions, including the following: Read all instructions before installation or use to prevent injury and appliance damage. This appliance conforms to all uniform safety codes and regulations. The manufacturer cannot be held responsible for damage or injury caused by improper use of this appliance.
Technical Safety ~ Installation, repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. ~ Before installing the combiset, check for externally visible damage.
~ Do not cook on a broken combiset. Any breakages or cracks in the ceramic surface of the appliance are defects and must be treated as such. If the combiset should break, cleaning solutions and spills may penetrate the broken combiset and create a risk of electric shock.
~ Do not store items on the appliance when not in use. Items could melt or catch fire from residual heat or if the appliance is turned on inadvertently. Always switch the cooking zone(s) off after use. ~ Flammable materials should not be stored on or near the appliance.
~ Pot and pan handles should be turned inward and not extend over the countertop to reduce the risk of burns, ignition of flammable materials, and spills. ~ Do not use pots or pans with pronounced edges or ridges on the ceramic combiset. These could scratch the combiset permanently.
CS 1212 a Burner with double booster (BI/II) b Burner with single booster (BI) c Display d Cooking zone indicators e Indicators Control knobs for the burners: f rear g front Indicators l On/Off indica.
CS 1221 a Burner with double booster b Display c Indicators d Control knob Indicators l On/Off indicator m Booster indicator n "Residual Heat" indicator Description of the unit 10.
Display ß = No pan on burner or pan is unsuitable A = Auto-heat F = Fault (see "Frequently asked questions") C / 0 = Safety cut-out feature (see "Safety features") I = Booster I a.
Clean the combiset ^ Before using for the first time, clean the appliance with a damp cloth and dry with a soft cloth. Do not use liquid dish soap to clean the combiset, this may cause permanent blue discolorations.
How it works An induction coil is located under the burner. When the burner is switched on, this coil creates a magnetic field which impacts directly on the base of the pan and heats it up. The burner itself is heated indirectly by the heat given off by the pan.
Noises When using an induction burner, the following noises can occur in the pan, depending on what it is made of and how it is constructed. – Higher power settings may cause a buzz. This will decrease or cease altogether when the power setting is reduced.
Cookware Suitable pans include: – stainless steel pans with a magnetic base – enameled steel pans – cast iron pans Unsuitable pans: – stainless steel pans without a magnetic base – aluminum .
Turning the combiset On/Off , Do not leave the appliance unattended while in use. To turn the combiset on turn the control knob clockwise a to the desired power level. To turn the combiset off turn the control knob counterclockwise b to "0".
Settings Use for Power level* Melting butter, chocolate, etc. Dissolving gelatin Prepare yogurt 1-2 Warming small quantities of food or liquid Keeping delicate dishes warm Cooking rice, Thawing frozen vegetables 1-3 Warming liquid or half-set foods Thickening sauces, e.
Auto-heat When Auto-heat has been activated, the burner switches on automatically at the highest setting and then switches to the continued power level which was selected. The "heat-up" time depends on which continued power level has been chosen (see table).
Booster function The burner is equipped with a booster function to temporarily increase the power level. This boost is intended to quickly bring large quantities of water to the boil, e.g. cooking pasta. When the Booster is activated the burner will operate with extra power for 10 minutes.
Keep warm This function can be used for keeping food warm right after it has been cooked. It is not for reheating food which has already cooled. Once activated the keep warm function will switch off automatically after 2 hours. Tips – Cover the pan with a lid.
Child Safety Lock Keep children away from the combiset for their own safety. The combiset has a Child Safety Lock to prevent children from turning on the burner. To activate the Child Safety Lock: ^ Turn the control knob counterclockwise as far as it will go, and hold until L appears in the display.
Overheating protection The induction coils and the cooling element of the electronics are fitted with an overheating protection feature. This prevents the induction coils and cooling element from overheating. This mechanism works in the following ways: – If the booster function is being used, it will be switched off.
Do not use a steam cleaner to clean this appliance. Steam could penetrate electrical components and cause a short circuit. Pressurized steam could cause permanent damage to the surface and to components for which the manufacturer cannot accept responsibility.
Stainless steel Clean stainless steel surfaces with warm water and liquid dish soap applied with a non-abrasive sponge and then wipe dry with a soft cloth. Soak baked or hardened spills first to loosen them. Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner (available from Miele).
, Repairs should only be carried out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage.
What if the combiset turns itself off automatically? Possible fault Solution Either the "Safety cut-out" feature or the "Overheating protection" feature has been activated. See "Overheating protection" or "Safety cut-out".
In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting Technical Service please quote the serial number and model of the appliance.
28.
Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE To prevent accidents and machine damage read these instructions before installation or use.
Note to the installer: Please leave this instruction book with the consumer for the local electrical inspector’s use. The minimum distances given in these Installation Instructions must be observed in order to ensure safe operation. Failure to do so increases the risk of fire.
Safety distances above the appliance The minimum safety distance given by the hood manufacturer must be maintained between the combiset and the hood above it.
Safety distances to the sides of the appliance The appliance should only be installed as shown in the illustrations, while maintaining the required safety distances shown.
Safety distance when installing the appliance near a wall with trim or a back splash A minimum distance of 2" (50 mm) between the trim or back splash and the countertop cut-out if required. This distance is only necessary if these items are made of combustible materials e.
Installation dimensions CS 1212 a Spring clips b Appliance front c Installation height d Power supply box with connection cable Installation 34.
CS 1221 a Spring clips b Appliance front c Installation height d Power supply box with connection cable Installation 35.
Cut out ^ Make the worktop cut-out for one or more appliances as applicable. Remember to maintain a minimum safety distance from the back wall , as well as from any tall unit or side wall to the right or left of the appliance(s). See also "SAFETY INSTRUCTIONS FOR INSTALLATION".
Installation of multiple appliances When installing more than one combiset appliance, a support bar b must be installed between the appliances. Countertop cut-out two appliances For the installation of two appliances the width of the countertop cut-out D is the sum of A and C.
Sample calculations for a countertop cut-out for three appliances A appliance width minus 5 / 16 "( 8m m ) B appliance width C appliance width minus 5 / 16 "( 8m m ) D Countertop cut-out 11&.
a Spring clips b Support bars c Space between support bar and countertop An additional support bar is required for each additional appliance. The position for attachment of an additional spacing strip depends on the width of the appliance B .
Attach the spring clips and support bars Wood or solid surface countertops ^ Place the supplied spring clips a and the support bars b at the marked positions as shown above, by laying them on the upper edge of the cut-out and then securing them with the 1 / 8 " x 1" (3.
^ Coat the edges of the spring clips a , ^ and the space d between the strips b and the countertop with silicone (supplied). Installation 41 b d a.
Installing the appliance ^ Feed the power cord down through the cut-out. ^ Then place the front side of the appliance in the countertop cut-out. ^ Then with a hand on each side of the appliance press down evenly on the edges until it clicks into position.
Sealing The appliance must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the appliance provides a sufficient seal for the countertop. If the appliance is sealed into position, the countertop or appliance could be damaged if it needs to be removed for maintenance or service.
, CAUTION: Before installation or servicing, disconnect the power supply by either removing the fuse, shutting off the main power supply or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards.
Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of an old appliance Old appliances contain materials that can be recycled.
46.
47.
Alteration rights reserved / 4608 For the most updated manual see the Miele web site. M.-Nr. 07 353 950 / 00.
デバイスMiele CS1212の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miele CS1212をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele CS1212の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele CS1212の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele CS1212で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele CS1212を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele CS1212の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele CS1212に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele CS1212デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
