MieleメーカーG600の使用説明書/サービス説明書
ページ先へ移動 of 108
TECHNICAL INFORMATION G600 & G800 Electr onic Dishwashers © 2003 Miele.
Technical Information G600 & G800 Electronic Di shwashers G600 & G800 Electronic Dishwashers – Table of Contents 1.0 Construction Design …………………………………………………………….8 1.1 Appliance Overview .........
Technical Information G600 & G800 Electronic Di shwashers G600 & G800 Electronic Di shwashers – Table of Contents (continued) 4.4.2.1 Flow Through Heater Electrical Data ........................ 28 4.5 Heater Circuit - Operation ............
Technical Information G600 & G800 Electronic Di shwashers G600 & G800 Electronic Di shwashers – Table of Contents (continued) 5.10 Door Panel (Outer and Inner) - Removal ........................................... 66 5.11 Cable Holder - Removal .
Technical Information G600 & G800 Electronic Di shwashers G600 & G800 Electronic Di shwashers – Table of Contents (continued) 6.0 Fault Diagnosis ……………………………………………………………….....98 6.1 General Information .
Technical Information G600 & G800 Electronic Di shwashers G600 &G800 Electronic Dishwashers – List of Figures 1-1: Appliance Overview - Typical Integrated Model ................................... 9 1-2: Appliance Overview – Ty pical Fully Integrated (Vi) Model .
Technical Information G600 & G800 Electronic Di shwashers G600 &G800 Electronic Dishwashers – List of Figures (continued) 5-11: Exterior view of the Inner Door Panel .................................................64 5-12: Fan Removal .....
Technical Information G600 & G800 Electronic Di shwashers G600 &G800 Electronic Dishwashers – List of Tables 1-1: Summary of Dimensions ...................................................................... 15 4-1: Detergent Quantity in Combination Dispensers.
Technical Information G600 & G800 Electronic Di shwashers 1.0 Construction and Design 1.1 Appliance Overview 1.1.1 Appliance Overview – Typical Integrated Model Figure 1-1: Appliance Overview - .
Technical Information G600 & G800 Electronic Di shwashers 1.1.2 Unit Overview – Typical Fully Integrated Model Figure 1-2: Appliance Overview – Typical Fully Integrated (Vi) Mod el 10.
Technical Information G600 & G800 Electronic Di shwashers 1.2 Controls Overview Miele dishwashers are currently ca tegorized into three (3) product series, based on the type of controls. Novotronic Each Novotronic model dishwas her can be operated with a single knob.
Technical Information G600 & G800 Electronic Di shwashers Incognito The Incognito (fully integrated) se ries dishwashers have the program controls located on the top edge of the door; and are accessed while the door is open.
Technical Information G600 & G800 Electronic Di shwashers 1.3 Types of Dishwashers Pre-Finished : The pre-finished construction consist of a pre-assembled door panel and control panel; making it an ideal replacement unit. Available in white, bla ck or stainless steel.
Technical Information G600 & G800 Electronic Di shwashers 1.4 Technical Data 1.4.1 Dishwasher Width – Fullsize / Slimline Figure 1-6: Dishwasher Widths 1.
Technical Information G600 & G800 Electronic Di shwashers 1.4.3 Summary of Dimensions FULLSIZE G600 Series G800 Series Height 32 ¼” - 34 7 / 8 ” 33 1 / 8 ”- 35” Width of Machine 23 1 / 2 .
Technical Information G600 & G800 Electronic Di shwashers 1.4.5 Hard Wire Electrical Connection Connections: L1 (Black) to L on te rminal block, N (White) to N on terminal block, GND To ground connector. Hard wiring the dishwasher s hould only be done if required by electrical code.
Technical Information G600 & G800 Electronic Di shwashers 1.5 Data Tag The Data Tag is located on the top edge of the door or on the right side edge of the door (fully integr ated models) - as shown.
Technical Information G600 & G800 Electronic Di shwashers 1.6 Layout of Components 1.6.1 Novotronic and Touchtronic Series 1 Temperature Limiter 90°C, 3F2.
Technical Information G600 & G800 Electronic Di shwashers 1.6.2 Incognito Series 1 Temperature Sensor, R30 2 Float Switch, B8/3 3 Level Switch - Heating, B1/10 4 Relay - Mains, 1K1/6 5 Relay - Hea.
Technical Information G600 & G800 Electronic Di shwashers 2.0 Installation Refer to the Appliance Installation Manual. 20.
Technical Information G600 & G800 Electronic Di shwashers 3.0 Commission and Operation 3.1 Door Handle and Door Lock (Novotronic and Touchtronic Series) Press the release catch inside the Door Grip. Note If the door is opened during operati on, the dishwasher will stop running.
Technical Information G600 & G800 Electronic Di shwashers 3.4 Water Softener If your tap water hardness is above 8 grains per gallon (140 ppm), the water should be softened.
Technical Information G600 & G800 Electronic Di shwashers 3.5 General Operation – Novotronic Series 1. Make sure the Spray Arms are not blocked. 2. Close the door. 3. Turn on the dishwasher. The "Start" Indicator will flash. 4. Select a wash program by turni ng the Program Select or to the left or right.
Technical Information G600 & G800 Electronic Di shwashers 4.0 Description of Function 4.1 Cabinet Construction The inner cabinet is constructed of stainless steel (1.4301) welded onto four (4) vertical U-section sub-frames. The cabinet is sound and heat-insulated with bitumen and/or mineral wool matting.
Technical Information G600 & G800 Electronic Di shwashers 4.3 Combination Dispenser 4.3.1 Construction Two individual solenoids control detergent and rinse aid dispensing. The Rinse Aid Reservoir has a capacity of about 130 ml. When the Rinse Aid level drops to about 25 ml .
G600 & G800 Electronic Di shwashers Technical Information 26 4.3.2 Dispensing During the main wash, the Detergent Solenoid (Y51) is energized (120VAC), to open the Detergent Dispe nser Flap. The water jet from the Middle Spray Arm flushes det ergent out of the dispenser.
Technical Information G600 & G800 Electronic Di shwashers Note To allow proper filling of the Rinse Aid Dispenser; Rinse Aid should only be added with the door in the fully open position.
Technical Information G600 & G800 Electronic Di shwashers 4.4.2 Flow Through Heater: The Flow Through Heater Assembly is mounted on the (left side) exterior of the wash cabinet. The Flow Through Heater is plumbed into the water path between the Circulation Pump Output and the Middle Spray Arm.
Technical Information G600 & G800 Electronic Di shwashers 4.5 Heater Circuit - Operation Figure 4-4: Heater Circuit 29.
Technical Information G600 & G800 Electronic Di shwashers 4.6 Pulsed Heating - Operation In certain programs the heating ma y be operated at full power until a water temperature of 77°F is reached; then power is applied in pulses. This extends the heating time and allows enzyme-containing detergents to develop their full cleaning potential.
Technical Information G600 & G800 Electronic Di shwashers 4.9 Spray Arms The circulation pump (M6) moves the wash water from the sump through the Filter Assembly and to the Spray Arms. The water pressure causes a propulsion effect causing the Spray Arms to rotate.
Technical Information G600 & G800 Electronic Di shwashers detergent should fall into the Microfi ne Filter, it remains on the Filter Cap, where it can dissolve, instead of collecting in the drain outlet. Foreign bodies which pass the Coarse Filter to the Microfine Filter collect on the Filter Cap and so they don’t clog the drain outlet.
Technical Information G600 & G800 Electronic Di shwashers 4.12 WaterProof System (WPS) The Water Inlet Valve (Y2) consis ts of two (2) electro-mechanical valves mounted within a waterpr oof box located at the water connection (end of the water intake hose).
Technical Information G600 & G800 Electronic Di shwashers With the Float Switch actuated; power that is normally distributed throughout the appliance is re-direct ed to the Drain Pump. The Drain Pump will continuously operate when t he unit is turned on and the door is closed.
Technical Information G600 & G800 Electronic Di shwashers WaterProof Sy stem Circ uit – normal operating position WaterProof Sy stem Circuit – Float Switch B8/3 a ctuated From water being present in the lo wer pan of the dish washer.
Technical Information G600 & G800 Electronic Di shwashers 4.13 Flowmeter - Operation The incoming water turns an impeller t hat contains a magnet located in the Flow Meter Axle. As the impeller turns, an external Reed Switch is switched on / off by the effect of the magnet.
Technical Information G600 & G800 Electronic Di shwashers 4.14 Water Intake If the water pressure is low, t he electronic can be programmed to increase the allotted intake duration fr om 2 minutes, to up to 4 minutes. For further information refer to the section 6 Fault Diagnosis.
Technical Information G600 & G800 Electronic Di shwashers 4.15 Water Mixing 4.15.1 Water Mixing - External Flowmeter Refer to figure 4-9. The main water flows into the Wate rProof system ( Ite m 10), to the Water Intake Assembly where it pa sses a Non-Return Device (Item 6).
Technical Information G600 & G800 Electronic Di shwashers 4.15.2 Water Mixing - Integrated Flowmeter 1 Drain pump 2 Sump 3 Sump - Soft water intake 4 Water softener - Soft water outlet 5 Solenoid .
Technical Information G600 & G800 Electronic Di shwashers Refer to the figure 4-12. The water intake hose from the WaterProof System (WPS) is connected to the Water Inlet Mixer ( Item 6). Hard water flows through the Integrated Flow Meter (Item 1) , and into the Intake Channel (Item 3), to Solenoid Valve Y5 (Item 4).
Technical Information G600 & G800 Electronic Di shwashers 4.15.3 Solenoid Valve (Y5) - Operating (Plus Models Only) Figure 4-13: Water Hardness Mixer Sol enoid Refer to figure 4-12. With no voltage to Y5 The Valve Pin (Item 5) closes the channel for cabinet ventilation.
Technical Information G600 & G800 Electronic Di shwashers 4.16 Electronic Controlled Water Hardness (EGS) To avoid possible glass corrosion, the wash water hardness level should not exceed or fall.
Technical Information G600 & G800 Electronic Di shwashers 4.17 Water Softener The Water Softener consists of 2 co mpartments - a Salt Container and an Ion Chamber. In addition it also has a mechanical Non-Return Valve, a Solenoid Valve and a Reed Switch / Magnetic Float Switch.
Technical Information G600 & G800 Electronic Di shwashers 4.17.1 Reactivation The electronic unit activates the So ftener Valve (Y38/1) and water from the Water Intake Assembly flows in to the Salt Container, where it dissolves a quantity of salt to become a brine mixture.
Technical Information G600 & G800 Electronic Di shwashers 4.17.2 Reactivation Cycles Water Hardness Number of Program sequences before reactivation (Universal 650C) Parts per Million Grains per Gallon Normal Water Quantity Increased Water Quantity 18 to 71 1 to 4.
Technical Information G600 & G800 Electronic Di shwashers 4.18 Condenser Drying (UKT) Does not apply to all dishwasher models 4.18.1 Operation An air inlet port is located on the back / left area of the cavity ceiling. An air duct is fitted to the por t and attaches to the Condenser Assembly.
Technical Information G600 & G800 Electronic Di shwashers 1 Water Control ValveY6 – (for Steam Condense r) 2 Fan M2 3 Vent / Water Port from condenser 4 Steam Condenser Assembly 5 Air Duct (Cond.
Technical Information G600 & G800 Electronic Di shwashers 4.18.3 Control Valve Refer to figure 4-15… The Miele Circulation Condenser Dryi ng System consists of a Steam Condenser (Item 4), with Circulation Fan.
Technical Information G600 & G800 Electronic Di shwashers 4.19 Drain Pump, Circulation Pump The Drain Pump (M8) is located below the cabinet and connects to the right / front of the Sump. The Pump removes the wash water through the Non-Return Valve and Drain Hose to the on-site drain.
Technical Information G600 & G800 Electronic Di shwashers If sufficient water and circ ulation is not present the switch is not actuated; this keeps the Heater Re lay circuit interrupted, the appliance malfunctions and a fault is stored in the Electronic.
Technical Information G600 & G800 Electronic Di shwashers 4.21 Level Switch (Intake Overflow) As an additional safety measure, the Overflow Level Switch (B1/2) is electrically in series to the Water Inlet Valves (Y2). The Level Switch interrupts power should the water le vel become to high inside the cabinet.
Technical Information G600 & G800 Electronic Di shwashers 4.22 Temperature Sensor The Temperature Sensor R30 (NTC re sistor) is located in the bottom area of the Sump. The Electronic Unit constantly monitors the water temperature using the resistance value of the sensor.
Technical Information G600 & G800 Electronic Di shwashers 4.23 Top Solo Valve Refer to figure 4-19. If the Top Solo option is selected, water is directed to the Top and Middle Spray Arms only. The Top Solo Valve (Y27) is located between the Circulation Pump and the Sump within the plumbing circuit to the Bottom Spray Arm.
Technical Information G600 & G800 Electronic Di shwashers 4.24 Turbidity Sensor (ECO Sensor) Certain model dishwashers are e quipped with a Turbidity (ECO) Sensor. The Sensor is comprised of a Phototransistor that emits a beam of light through the water pat h.
Technical Information G600 & G800 Electronic Di shwashers The sensor is located within the plumbing connection between the Circulation Pump and Top Spray Arm.
Technical Information G600 & G800 Electronic Di shwashers 4.25.1 Programming After Replacing the Electronic In addition to Intake Duration and Water Softener Settings certain dishwasher Electronics need to be programmed for the width of the dishwasher (45 cm or 60 cm).
Technical Information G600 & G800 Electronic Di shwashers 5.0 Service and Maintenance 5.1 Locking Plate - Adjustment Figure 5-1: Locking Plate 1. Loosen the two Screws (Item 1). 2. Adjust the Locking Plate in the di rection of the arrow as required 3.
Technical Information G600 & G800 Electronic Di shwashers 5.3 Side Panel - Removal Figure 5-3: Side Panels and Cabi net Refer to figure 5-3 With the appliance removed from it’s installation location 2. Remove the raised head screws (Items 1 and 3).
Technical Information G600 & G800 Electronic Di shwashers 5.4 Spring Bracket - Replacement Figure 5-4: Side View, Door with Bracket 1. Remove the Side Panels (5.3) 2. Fold up the Mineral Wool Matting (depending on model). 3. Hold the Spring with one hand and pull it down.
Technical Information G600 & G800 Electronic Di shwashers 5.5 Cover Plate - Removal Figure 5-5: Cover Plate 1. Remove the two Screws and the Plinth (Toekick). 2. Remove the Raised Head Screws, (Figure5-5 – Item 1). 3. Tilt the Cover Plate forwards slightly and lift its bottom edge out of the Drip Tray.
Technical Information G600 & G800 Electronic Di shwashers 5.6 Connecting Strip - Removal Figure 5-6 : Plinth area with Connecting Strip 1. Remove the Cover Plate (5.5). 1. Remove the Raised Head and Count ersunk Screws (Figure 5-6 – Item 1). 2. Remove components from the Connecting Strip.
Technical Information G600 & G800 Electronic Di shwashers 5.7 Basket Support Rollers – Replacement Figure 5-7: Bask et Guide Warning! Do not attempt to pry the Basket Gu ides free with a screwdriver; this will result in irreversible damage to the cabinet walls.
Technical Information G600 & G800 Electronic Di shwashers 2. Insert a small screwdriver under the Clip between the Bolt on the cabinet wall and the Basket Guide and remove the Clip upwards. 3. Remove the Basket Guide. Figure 5-9: Basket Guide Stopper 4.
Technical Information G600 & G800 Electronic Di shwashers 5.8 Combination Dispenser - Removal Figure 5-11: Exterior view of the Inner Door Panel 1. Remove the Outer Door Panel (5.10). 2. Disconnect all Electrical Plugs; and Hose – if fitted with a Fan.
Technical Information G600 & G800 Electronic Di shwashers 5.9 Turbothermic Fan - Removal 1. Remove the Outer Door Panel (5.10). 2. Remove the Control Panel. 3. Remove the Fixing Bracket. Components can remain on the Fixing Bracket (i.e. Electronic Unit, Handle) Figure 5-12: Fan Removal 4.
Technical Information G600 & G800 Electronic Di shwashers 5.10 Door Panel (Outer and Inner) - Removal Note This procedure does NOT apply to Pre-Finished models. To Remove the Outer Door Panel 1. Remove the GDU or Custom Panel 2. Open the front door.
Technical Information G600 & G800 Electronic Di shwashers 5.11 Cable Holder - Removal Figure 5-14: Cable Holder Removal Refer to figure 5-14. 1. Remove the Outer Door Panel (5.10). 2. Open the Cable Holder Cover with a screwdriver. 3. Remove the Raised Head Screw (Figure 5-14 – Item 1).
Technical Information G600 & G800 Electronic Di shwashers 5.12 Lock / Handle Assembly – Removal Figure 5-15: Lock Removal Caution Ensure the power is disconnected at the wall outlet; by shutting off the appropriate circuit breaker 1. Remove the Outer Door Panel (5.
Technical Information G600 & G800 Electronic Di shwashers 5.13 Door Hinge - Removal Refer to Figure 5-16. 1. Remove the Side Panel (5.3). 2. Remove the Outer Door Panel (5.10). 3. Remove the Tensioning Spring (5.4). Figure 5-16: Hinge Removal Warning! Ensure the Door is held in posit ion; and supported while opening it.
Technical Information G600 & G800 Electronic Di shwashers 5.14 Door Tension - Adjustment 1. Open the Door. 2. Locate the Spring Adjustment Screw on the left side of the dishwasher at the top front edge – as shown in Figure 5-17. 3. Use a Torx 20 screwdriver to adjust the Screw as follows: Clockwise – Tighten.
Technical Information G600 & G800 Electronic Di shwashers 5.15 Top Spray Arm - Removal 1. Open the Door. 2. Press the Top Spray Arm upwards to engage it. 3. Unscrew clockwise. 5.16 Middle Spray Arm - Removal 1. Open the Door. 2. Remove the Upper Basket.
Technical Information G600 & G800 Electronic Di shwashers 5.19 Middle Spray Arm Cover - Removal Figure 5-18: Middle Spray Arm Cover Removal 1. Insert a large screwdriver between the Cover Retainer and the Metal Holder on the rear of the cabinet wall – see figure 5-18.
Technical Information G600 & G800 Electronic Di shwashers 5.21 Flow-Through Heater - Removal Refer to figure 5-19. 1. Remove the Left Side Panel (5.3). 2. Fold up the insulation – as needed. Figure 5-19: Dishwasher with Flow-Through Heater 3. Disconnect the Electrical Connections.
Technical Information G600 & G800 Electronic Di shwashers 1 3 2 1 – Seal 2 – Flow Through Heater 3 – Tem p erature Limiters Figure 5-20: Flow-Through Heater with Seal (Item 1). 5.22 Temperature Limiter - Replacement 1. Remove the Left Side Panel (5.
Technical Information G600 & G800 Electronic Di shwashers 5.23 Microfine Filter – Exchange Refer to figure 5-21. 1. Open the Door. 2. Remove the Filter Assembly from the dishwasher. Figure 5- 21: Microfine Filter – Replacem ent 3. Cut the old Filter combination apart at the Snap Fitting between the Handle and Microfi ne Filter (Item 4).
Technical Information G600 & G800 Electronic Di shwashers 6. Apply a small amount of Rinse Aid to act as a lubricant while snapping the new Microfine Filter into place. 7. Apply pressure with both thumbs inside the Microfine Filter and press it onto the Handle (Figure 5-22), so that the parts lock together.
Technical Information G600 & G800 Electronic Di shwashers 5.25 WaterProof System (WPS) Restrictor - Exchange 1. Shut off the water supply. 2. Disconnect the WPS at the plumbing supply connection. 3. Remove the Sealing Washer and Filter from inside the WPS connection 4.
Technical Information G600 & G800 Electronic Di shwashers 5.26 Water Inlet (Diverter) - Removal 1. Open the Door. 2. Unscrew the connections securing the Water Intake to the inside of the cabinet; as shown in Figure 5-25. Figure 5-25 : Water Inlet - Removal 3.
Technical Information G600 & G800 Electronic Di shwashers 5.27 Water Softener – Operational Check Service Tip Ensure the Electronic is programmed “ with Water Softener ” before performing the following procedure.
Technical Information G600 & G800 Electronic Di shwashers 5.28 Water Softener Assembly- Removal 1. Open the Door; remove the Salt Container Cap and Sealing Ring. Remove any excess water / brine as necessary. 2. Remove the Right Side Panel (5.3). 3.
Technical Information G600 & G800 Electronic Di shwashers 5.31 Float Switch (B8/3) – Removal Refer to figure 5-26 . Figure 5-26: Float Switch Housing 1. Remove the Float Switch Housing (5.30). 2. Unclip the Top and Side Retainers (Items 1 and 2).
Technical Information G600 & G800 Electronic Di shwashers 5.32 Steam Condenser - Removal 1. Remove the Left Side Panel (5.3). 2. Open the Door. 3. Unscrew the Top Air Duct Cap (Intake Connection). 4. Unscrew the Bottom Air Duct Cap from the Steam Condenser (Bayonet Connection).
Technical Information G600 & G800 Electronic Di shwashers 5.33 Control Valve (Y6) - Removal 1. Lay the dishwasher on it’s back. 2. Remove the Drip Tray (5.29). 3. Disconnect the Electrical Connection to the Valve. 4. Note position of all Hoses. Disconnect the Hose Connections.
Technical Information G600 & G800 Electronic Di shwashers 5.35 Circulation Pump (M6) - Removal Refer to figure 5-28 1. Remove all water from the Sump. 2. Remove the Fixing Bolt (Item 5) , from the Casing Rear Panel (Item 4). Figure 5-28: Circulation Pump – Removal 3.
Technical Information G600 & G800 Electronic Di shwashers 5.36 Circulation Pump - Partition & Impeller Replacement Warning! To avoid the risk of leaks; all par ts included in the Partition / Impeller Kit should be installed during this procedure.
Technical Information G600 & G800 Electronic Di shwashers 5.37 Circulation Pump Housing - Exchange 1. Remove the Circulation Pump (5.35). 2. Remove the four (4) Sc rews from the pump housing. 3. Fit the new Pump Housing and O-ring. 5.38 Circulation Pump – Release with Tool 1.
Technical Information G600 & G800 Electronic Di shwashers Figure 5-32: Turning th e Circulation Pump Tool 5. Carefully turn the Releasing Tool back and forth about its axis to release the Pump Impeller.
Technical Information G600 & G800 Electronic Di shwashers 5.39 Heater Level Switch (B1/10) – Removal Refer to figure 5-33. 1. Remove as much water as possible from the Sump. 2. Lay the Dishwasher on it’s back. 3. Remove the Drip Tray (5.30). 4.
Technical Information G600 & G800 Electronic Di shwashers 5.40 Drain Pump (M8) – Removal Refer to figure 5-34. 1. Remove as much water as possible from the Sump. 2. Remove the Cover Plate (5.5). 3. Disconnect the Electrical Connection (Item 1). 4.
Technical Information G600 & G800 Electronic Di shwashers 5.41 Top Solo Valve - Removal 1. Remove the Circulation Pump (5.35). 2. Disconnect the Electrical Connection. Warning It is essential to note correct position of the Valve before removal. (The direction of flow is marked by an arrow on the Valve Housing) 3.
Technical Information G600 & G800 Electronic Di shwashers 5.42 Overflow Level Switch - Removal Refer to figure 5-36 1. Remove as much water as possible from the Sump. 2. Remove the Cover Plate (5.5) 3. Locate the Overflow Level Swit ch mounted on the right / rear side of the Connecting Strip.
Technical Information G600 & G800 Electronic Di shwashers 5.43 Sump - Removal 1. Remove as much water as possible from the Sump. 2. Open the door; remove the Bottom Spray Arm (5.17) and Filter Assembly. 3. Lay the dishwasher on its back. 4. Remove the Drip Tray (5.
Technical Information G600 & G800 Electronic Di shwashers 5.44 Turbidity Sensor - Calibration After installing a new Electronic and / or Turbidity Sensor the dishwasher must be run through a complete program without any dishes.
Technical Information G600 & G800 Electronic Di shwashers 5.46 Fully Integrated (Vi) Control Panel - Removal Refer to figure 5-39. 1. Open the Door. 2. Hold the Fascia Panel (Item 9) while removing the interior Screws (Item 10). 3. Lift the Fascia Panel (Ite m 9) from the appliance.
Technical Information G600 & G800 Electronic Di shwashers 5.47 Novotronic & Touchtronic Control Panel – Removal Refer to figure 5-40 . 8 Pushbutton Switch 9 Electronic Unit 10 Adapter for Pr.
Technical Information G600 & G800 Electronic Di shwashers 5.48 Fixing Bracket – Removal Service Tip The Fixing Bracket is removed to access to the following components: Turbothermic Fan / P TC Release On / Off Button Door Handle / Lock Assembly Electronic(s) B A Figure 5-41: Removing the Fixing Bracket Refer to figure 5-41.
Technical Information G600 & G800 Electronic Di shwashers 5.49 Heating Relay & Power Relay – Removal Service Tip Make note of wiring posi tion for re-installation. 1. Remove the Left Side Panel (5.3). 2. Locate the Relay (location varies by model number).
Technical Information G600 & G800 Electronic Di shwashers 6.0 Fault Diagnosis 6.1 General Information Every electronic controlled Miel e dishwasher has three modes accessible for services purposes: Programming Mode Service Mode One Service Mode Two 6.
Technical Information G600 & G800 Electronic Di shwashers 6.2.4 Buzzer (As Applicable) Applies only to fully int egrated (Vi) dishwashers (except Plus series). Can be used to add an audible alarm at the end of the program. 6.2.5 Fault Code (Retrieval) Stores the last fault registered, to assist in troubleshooting.
Technical Information G600 & G800 Electronic Di shwashers 6.2.9 Width of Unit (As Applicable) Some Electronic Units can be installed in more than one specific model number; and therefore require pr ogramming the width of the dishwasher it is being installed in.
Technical Information G600 & G800 Electronic Di shwashers 6.4 Timing Charts – General Information 101.
Technical Information G600 & G800 Electronic Di shwashers A Timer Steps Run along the left and right side of the chart numbered 1-50. All fifty steps do not apply to every program , refer to E and F for further information. B The component names and Wiring Diagram Legends are listed here.
Technical Information G600 & G800 Electronic Di shwashers C Time Column , indicates the length in time the step occurs. Minutes are on the left side of the column, wh ile seconds are displayed on the right side of the column.
Technical Information G600 & G800 Electronic Di shwashers E Program Choices and steps performed… Understanding the steps pe rformed Clear (White) Blocks indicate the step is performed.
Technical Information G600 & G800 Electronic Di shwashers 6.5 Wiring Diagrams – General Information 1 Electronic Assembly (Circuit Boards) 2 Molex Plug Connectors (framed by dotted lines) 3 “Current Path” to identify the loca tion of the component along a numbered line.
Technical Information G600 & G800 Electronic Di shwashers 6.7 Fault Repair Door does not close correctly Incorrectly fitted Stopper at end of Top Basket Guide. - Remove the Stopper and fit it correctly (5.7). Door Seal incorrectly fi tted and protrudes forwards.
Technical Information G600 & G800 Electronic Di shwashers Water leaks from the Turbothermic Fan Grille Hose between Fan and Dispenser is blocked - Inspect Hose and replace as necessary (5.9) The PTC Flap is not closing correctly - Inspect Flap – replace the Turbothermic Fan as necessary (5.
Technical Information G600 & G800 Electronic Di shwashers Water not heating One of the Temper ature Limiters is not functioning - Check the Temperature Limiters Warning! Before resetting the T.
デバイスMiele G600の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Miele G600をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele G600の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele G600の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele G600で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele G600を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele G600の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele G600に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele G600デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。