MieleメーカーW3033の使用説明書/サービス説明書
ページ先へ移動 of 56
Operating and Installation Instructions Washer W 3033 To prevent accidents and machine damage, read these instructions before installation or use. M.-Nr.
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Control panel .....................
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Cleaning the exterior and control panel ................................2 7 Cleaning the drum ........................................
, WARNING - To reduce the risk of fire, electric shock or injury to persons while using your appliance follow basic safety precautions, including the following: Read all instructions before using the appliance. GROUNDING INSTRUCTIONS This appliance must be grounded.
If the power cord is damaged it must only be replaced by a Mile Service technician with a genuine Mile power cord. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE.
Control panel a Program buttons To select a wash program b Option buttons Special features to enhance a wash program c PC Indicator Allows a service technician to check and update the wash programs d .
Display function The display allows you to operate and select various functions of the washer. Selection and display of program settings – Temperature selection – Spin speed selection – Delay st.
The appliance must be correctly installed and connected before the first use. Please see the "Installation instructions." Running a spin cycle before the first use is, for safety reasons, not possible. To activate the spin cycle a wash program must be run without laundry or detergent .
1. Prepare and sort the laundry ^ Empty all pockets. , Foreign objects left in pockets (e.g. nails, coins, paper clips, etc.) can cause damage to clothes and the machine.
2. Turn on the washer ^ Press the I-On / 0-Off button. The washer is turned on and the program indicators light. 3. Load the laundry ^ Press the "Door" button to open the drum door. ^ Load the laundry loosely into the drum. For best results, wash mixed loads of small and large items.
4. Select a program ^ Press the button of the desired program. See the "Program guide" for information about the programs. The indicator of the selected program lights. 5. Select a temperature and/or spin speed The pre-selected temperature and/or spin speed can be adjusted if the program allows so.
Program guide Temperature Final spin Item / Tip Normal Options: Heavy Soil, Extended, Sensitive, Buzzer Hot D Max spin Items made from cottons, linen or mixed fabrics. Important: Fill the drum only 3 / 4 of the way. Items need room to move otherwise they might get caught in the drum door seal.
Temperature Final spin Item / Tip Woolens Options: Sensitive, Buzzer Warm B High spin Med spin Slow spin Hold No spin Items made from washable wool or mixed woolens. Cold A No Heat Silk Options: Buzzer Cold M Slow spin Silk and hand washable items which do not contain wool.
Temperature Final spin Item / Tip Delicates Options: Extended, Sensitive, Buzzer Warm N Med spin Slow spin Hold No Spin For delicate items made from synthetics. Cold M No Heat Denim / Jeans Options: Heavy Soil, Extended, Sensitive, Buzzer Warm B High spin Med spin All items made from denim.
Temperature Final spin Item / Tip Beach towels Options: Buzzer No Heat A Max spin Program to rinse sand from beach towels. Do not use detergent. Express Options: Buzzer Warm B Max spin High spin Med spin Slow spin Hold No Spin Small loads of mixed items for the programs "Normal" and "Wrinkle free".
Final spin speed Program Normal Max spin Wrinkle-free High spin Sanitize Max spin Handwash Med spin Woolens High spin Silk Slow spin Custom Max spin Extra White Max spin Delicates Med spin Denim/Jeans.
6. Select an option ^ Select the desired Option with the respective button. Once an Option is selected, the indicator lights. See the "Program Guide" to determine which Option is selectable for each program. If an Option cannot be selected, the wash program does not permit it.
7. Add detergent Front loading washing machines require special high efficiency detergents . Closely follow the requirements of the detergent manufacturer. Use detergent according to the laundry soiling. Use less for smaller loads. Light soiling No soiling or stains are visible.
Using liquid detergent ^ Pull out the detergent dispenser drawer and add detergent to the compartments. You can not combine "Heavy soil" and use bleach in the same cycle. The "Heavy soil" function flushes away the bleach prematurely.
Using powder detergent Liquid detergent inserts come already inserted in the detergent compartments. To use powder detergent remove the inserts. ^ Remove the inserts from both compartments j and i .
You can use all high efficiency detergents which are formulated for household washing machines. Closely follow the requirements of the detergent manufacturer.
Fabric softener Makes fabrics feel softer and reduces static cling in the dryer. Mild liquid starch A synthetic starch wash that gives fabrics some stiffness. Starch Gives the fabrics stiffness and volume. Dispensing fabric softener or liquid starch ^ Add the fabric softener, mild liquid starch or starch to compartment § .
8. Select Delay Start (if desired) Delay start allows you to delay the start of a program from 30 minutes up to a maximum of 24 hours. ^ Press the "Delay" button. Duration: 1:02 h M GGPGGG M M GGGGPG M Warm High spin ^ With every touch of the "Delay" button, the start is delayed longer.
10. Activate the Child Lock (if desired) The Child Lock can be activated to prevent a child from canceling the program and opening the door at the end of a program.
Canceling a program A program can be canceled any time after the program start. ^ Press and hold the "Cancel" button until the display shows: Cancel The wash water will be drained away. To add or remove laundry ^ Open the drum door. To select another program The display requests the program selection.
Adding/removing laundry during a wash program ^ Press and hold the door button until the door opens. ^ Add or remove laundry. ^ Close the door. The program continues automatically. Note: Once the program has started the washer can not make adjustments of the load size.
Quick guide Remove this guide for easy reference Please read all instructions, especially the "Important Safety Instructions", before using the washer.
1. Sort the laundry ^ Empty all pockets. ^ Sort the laundry by fabric and color. ^ Pretreat stains. 2. Turn on the washer ^ Press the "On/Off" button. The washer is turned on and the program indicators light. 3. Load the laundry ^ Press the "Door" button and load the laundry.
6. Selecting an Option ^ Select the desired Option with the respective button. Once an Option is selected, the indicator lights. 7. Add detergent ^ Add detergent to the respective compartments. 8. Selecting Delay Start ^ Press the " m " delay start button.
Program guide Sanitize Hot Very Warm Warm Cold No Heat Max spin High spin Med spin Slow spin Rinse hold No Spin Normal XX X XX X Wrinkle-free XXX X X X X Sanitize X X X X Handwash X X X X Woolens X X .
, Before cleaning or maintenance, disconnect the power supply by unplugging the unit or manually "tripping" the circuit breaker. , Do not use a hose to wash down the washer.
^ Clean the siphon tube. 1 . Remove the siphon tube from the compartment § and rinse under warm water. Clean the pipe on which the siphon tube is attached. 2 . Replace the siphon tube. Clean the siphon tube and fabric softener channel more often when frequently using liquid starch.
Cleaning the water inlet filters The washer has two water inlet filters to protect each inlet valve. These filters should be checked and cleaned if necessary every 6 months. This may need to be done more frequently with some water supplies. ^ Turn off the water supply.
Cleaning the drain pump and lint trap Occasionally, small objects (buttons, coins, etc.) may become trapped in the lint trap. If the machine does not drain completely, the lint trap should be checked to ensure that it is free of foreign objects. ^ Turn off the appliance with the "On / Off" button.
Once the flow of water stops: ^ Remove the lint trap lid. ^ Remove any foreign objects or lint from the filter. ^ Check that the impeller (in the back of the chamber) rotates freely by spinning it with your hand. ^ Return the lint trap and tighten into place.
, Repairs to electrical appliances must only be carried out by a qualified and trained person in accordance with local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held responsible for unauthorized work.
The display shows a fault message Issue Possible fault Fix 1) q Drain fault Check drain – The drain is blocked. – The drain hose is too high. – Clean the drain filter and the drain pump. – The maximum drain pump height is 3 ft (1m). p Water inlet fault Open water faucet – The water intake is blocked.
General problems with the washer Issue Possible cause Solution The washer shakes during the spin cycle. The four feet are not resting evenly on the floor. Level the machine (see "Leveling the washer"). There are unusual sounds coming from the drain pump.
Poor wash results Issue Possible cause Solution The wash does not come clean with liquid detergent. Liquid detergents do not contain bleaching agents. Fruit, coffee and tea stains cannot be effectively removed. – Use powdered bleach. – Do not put liquid detergent and stain remover together in the same wash compartment.
The drum door cannot be opened Possible cause Solution The washer is not plugged in and/or not turned on. Plug the washer in and turn it on by pressing the "I-On/0-Off" button. The Child Lock is activated. Deactivate the Child Lock as described in the chapter "Using the washer - Activating the Child Lock".
Opening the drum door during a power failure ^ Open the detergent dispenser drawer and remove the tool. ^ Open the lint trap door. ^ Drain the water from the washer as described in "Cleaning and Care - Cleaning the drain pump and lint trap".
Repairs In the event of a fault which you cannot fix yourself, please contact the technical service using the information on the back of this manual. ^ Please quote the model and serial number of your appliance when contacting the Technical Service Department.
Installation Instructions To prevent accidents and machine damage read these instructions before installation or use..
Front view a Hot water intake hose b Cold water intake hose c Power cord d - g Drain hose (drain options shown i.e adjustable and removable elbows). h Control panel i Detergent dispenser drawer j Drum.
Rear view a Lid excess end with transport grips b W-LAN communication module c Power cord d Cold water intake hose e Hot water intake hose f Drain hose g Shipping struts with rotary protection h Brack.
Installation site A concrete floor is the most suitable surface for the washer. Concrete floors are less prone to vibration during the spin cycle than wooden floors. Note: – The machine must be leveled and securely positioned. – To avoid vibration while spinning, the machine should not be installed on soft floor coverings.
^ Turn the left shipping strut counterclockwise 90° with the enclosed combination wrench. ^ Pull out the shipping strut. ^ Turn the right shipping strut clockwise 90° with the enclosed combination wrench.
^ Close the holes with the rotary protectors, making sure to close the caps. ^ Fasten the shipping struts to the rear of the washer. Take care to insert the drill holes correctly, b , into the clamps, a . , Do not move the washer without the shipping struts in place.
Leveling the washer To ensure smooth operation the washer must be level. Failure to level the machine can result in increased water and energy consumption as well as the washer "banging" in the spin cycle or "walking" across the floor during use.
The washing machine can be connected to a portable water supply. A non-return valve is not needed unless required by building code. The washing machine has ½" (13 mm) pressure hoses with 3 / 4 " (19 mm) female hose thread connections. If there is no water hookup, contact a plumber to install a connection.
Water connection ^ Connect the cold water intake hose (blue mark) to the cold water valve and the hot water intake hose (red mark) to the hot water valve.
Drainage The 5 foot (1.5 m) drain hose may be connected as follows: 1. Directly into a sink: hook the hose over the edge of the sink and secure it firmly (e.g. by tying the hose to the water faucet). 2. To a stand pipe: place the drain hose int oa1½ "( 4c m ) stand pipe and secure it firmly.
GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug.
The display language can be changed at any time as long as no program is running. ^ Press the "Extended" button until the display shows: Language english B + OK ^ Select the desired language by pressing the left menu button " + ". Confirm with " OK ".
Disposal of the packing material The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children, as they pose a danger of suffocation.
Alteration rights reserved / 1307 For the most updated manual see the Miele website. M.-Nr. 06 911 002 / 01.
デバイスMiele W3033の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Miele W3033をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMiele W3033の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Miele W3033の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Miele W3033で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Miele W3033を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMiele W3033の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Miele W3033に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMiele W3033デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
