Moxa TechnologiesメーカーUPORT 1100の使用説明書/サービス説明書
ページ先へ移動 of 45
UPort 1 100 Series User ’ s Manual Fourth Edition, April 2009 www .moxa.com/product © 2009 Moxa Inc. All righ ts reserved. Reproducti o n wi t ho ut perm ission is prohi bi t e d.
UPort 1100 Series User’s Manual The software d escribed in this m anual is furnished under a license agreem ent and may be use d only in accordance with the term s of that agreement. Copyright Notice Copyright © 2009 Moxa Inc. All rights reserved. Reproducti o n wi t ho ut perm ission is prohi bi t e d.
Table of Contents Chapter 1 Introduction .............................................................................................. 1-1 Overview ......................................................................................................
1 1 Chapter 1 Introduction The UPort 1100 Series of USB-to- s er ial converters provide an easy way to add CO M ports to your computer. The U Port 1110 prov ides one RS-232 po rt, the UPort 113 0 provides on e RS-422/RS-485 port, and the UPort 1150 and UPor t 1150I each prov ide one RS-232/4 22/485 port.
UPort 1100 Series User’ s Manual Introduction Overview The UPort 1110, UPort 1130, and UPort 1150/11 50I are part of Moxa’s UPort line of USB-to-serial converters. The UP ort line provi des a range of easy -to-use solutions for adding COM ports through a PC’s USB port.
UPort 1100 Series User’ s Manual Introduction Product Features The UPort converter has the follo wing features: y Full-Speed USB operation at up to 12 Mbps y Additional I/ O or IRQ not required y Serial transm ission speed up to 921.
UPort 1100 Series User’ s Manual Introduction Material UPort 1110/1130 /1150: ABS + PC UPort 1150I: Metal Gross Weight UPort 1110/113 0/1150: 60 g (0.
UPort 1100 Series User’ s Manual Introduction LED Indicators Active RxD TxD 1110 USB-to-Serial Adaptor Active RxD TxD 1130 USB-to-Serial Adaptor Active RxD TxD 1150 USB-to-Serial Adaptor RS-232/422/.
UPort 1100 Series User’ s Manual Introduction TR 150 KX 1K 2 1 ON DIP 3 Adjustable Pull High/low, Terminat or Resistors for the RS-485 Port In some critical environments, you may need to add termination resistors to prevent the reflection of serial signals.
2 2 Chapter 2 Installation and Configuration Installation of the converter is a simple process. Fi rst install the driver, then plug the converter into a USB port. When the converter is plugged in, Windows will load the correct dr ivers for the converter and the new COM port.
UPort 1100 Series User’s Manual Installation and Configuration Initial Driver Installation The Document ation and Software CD contain the drivers for the co nverter. You may also download th e drivers at www.moxa.com . The installation procedure is the same for all Wind ows operating systems.
UPort 1100 Series User’s Manual Installation and Configuration 2. Click Next to install the driver in the indicated folder, or use the drop-down folder list to locate a different folde r.
UPort 1100 Series User’s Manual Installation and Configuration 4. A window will pop up cautioning you that this software has not passed Windows logo testin g. This is a standard warning, and Mox a has thoroughly tested the dr iv er for safe Windows operation.
UPort 1100 Series User’s Manual Installation and Configuration Hardware Installation After installing the driver, plug the conv erter into any upstrea m USB port, such as a USB port on your computer. W indows will automatically detect the converter and b egin installing the driver.
UPort 1100 Series User’s Manual Installation and Configuration 3. Windows will automatically detect and install th e n ew serial port. No further action is required Windows XP, Windows 2003, and Win dows Vista (32-bit and 64-bit) The following in structions are for Windows XP , Windows 2003, and Windows Vista systems.
UPort 1100 Series User’s Manual Installation and Configuration 3. On the next wi ndow that appears, select Install the software automatically (Recomme nded) , then click Next .
UPort 1100 Series User’s Manual Installation and Configuration 5. Windows will spend a few moments installing the UPort driver. 6. The next window indicates that Windows has completed the installation. Click Finish to continue with installation procedure.
UPort 1100 Series User’s Manual Installation and Configuration 8. The Found New Hardware Wizard will open. If you see the following screen, select No, not this time , then click Next . 9. After a moment, the Found New Hardware Wizard will open. Select Inst all the software automatically (Recommende d) , then click Next .
UPort 1100 Series User’s Manual Installation and Configuration 10. The installation wizard will search for the correct drivers. After a moment, a window will pop up cautioning you that this software has not passe d Windows logo testin g. This is a standar d warning, and Moxa has thor ou g hl y test ed t he dri ver for safe Windows operati on.
UPort 1100 Series User’s Manual Installation and Configuration 12. The next window indicates that Windows has completed the installation. Click Finish to proceed with inst all a t i on pr o cedu re. 13. The Found New Hardware balloon will reappear, indicating that the installation was successful.
UPort 1100 Series User’s Manual Installation and Configuration Configuring the COM Port After the driver and hardware have been succe ssfully in stalled, the new COM port will have a COM number and can be accessed and controlled ju st like your PC’s built-in COM ports.
UPort 1100 Series User’s Manual Installation and Configuration Configuring the Converter If you need to change t he COM number that the co nverter assigns to the COM port, or ad just other advanced settings, you may go to Device Manager and right-click the UPort converter, which will be listed u nder Multi-por t serial adaptors .
UPort 1100 Series User’s Manual Installation and Configuration In the Port Configuration tab, you will see the new COM port listed. Click Port Setting to modify the C OM number and ot her parameters.
UPort 1100 Series User’s Manual Installation and Configuration You may chan ge the Port Num ber and enable or disa ble the Fast Flush f unction. For the UPort 1130, you m ay also select between RS- 422, 2-wire RS-485, and 4-wire RS-485 modes.
UPort 1100 Series User’s Manual Installation and Configuration Removing the Converter The converter i s a plug and pl ay device. No special proce dures are requi red to remove the converter; yo u may simply pull the converter o ut of the USB p ort. You shoul d verify that no data is being transmitted before removin g the converter.
UPort 1100 Series User’s Manual Installation and Configuration Uninstalling the Driver The UPort d river may be remove d through Ad d/Remove Pro grams in the Wi ndows Control Panel . Click Remove next to MO XA UPort 1110/1130/1150 Window s Driver Ver1.
UPort 1100 Series User’s Manual Installation and Configuration Install Linux Driver Linux Kernel 2.4.20 and above The Linux driver for the Moxa UPort 1000 Series converters will map Linux host ttyUSBxx po rts to UPort devic e ports.
UPort 1100 Series User’s Manual Installation and Configuration Unloading the Moxa Driver The driver will not be unloaded when you remove the MOXA UPort 1100 from the PC.
UPort 1100 Series User’s Manual Installation and Configuration In this section, we provid e four proce dures to introduce the Moxa Linux Driver. 1. Installing Linux Driver File 2. Loading/Unload ing the Moxa Driver 3. Setting the Serial Parameters 4.
UPort 1100 Series User’s Manual Installation and Configuration Setting the Serial Parameters The UPort 1 130 supports thre e interfaces (RS-48 5 2W, RS-485 4 W, RS-422) an d the UPort 1150/1150I supports four interfaces (RS-232, R S-4 85 2W, RS-485 4W, RS-422).
UPort 1100 Series User’s Manual Installation and Configuration Installation with an installation package for Win CE 6.0 Installation procedure Copy the UP ort 1200/140 0/1600 WinCE 6.
UPort 1100 Series User’s Manual Installation and Configuration Step 2: The WinCE 6.0 OS Design Wizard will start, click “ Next ” to continu e . In the “Board Support Packa ges” page, select the “CEPC: x86.
UPort 1100 Series User’s Manual Installation and Configuration Step 3: Under Design Templates and Design Template Variants, select your environment, such as PDA Device or Mobile Handheld, and th en click Next . I n Application & Me dia and Networking & Communication, als o select your enviro nment, such as .
UPort 1100 Series User’s Manual Installation and Configuration 2-25.
UPort 1100 Series User’s Manual Installation and Configuration Step 4: When the OS Design Projec t Wizard Complete screen appears, click Finish . The notification will pop up.
UPort 1100 Series User’s Manual Installation and Configuration Step 5: Open the project you c reated. Click Project on top of the screen, and the n select Add Existing Subproject . Switch the folder to “C:MOXAUPORTwin ce600 Uport” and add subprojects into your OS Design .
UPort 1100 Series User’s Manual Installation and Configuration Step 6: After the subproject is adde d, you may configure the “mxup ce6.reg” registry file with the location [HKEY_LOCAL_MACHINEDriv ersUSBClientDriv ersMXU_PO RT]. Step 7: Open “ B uild ”, select “ Advanced Build Commands ” and “ Build Sysgen ”.
UPort 1100 Series User’s Manual Installation and Configuration Step 8: After building sysgen, select “Build” and “Make Run-Time Image” to create the WinCE OS image.
UPort 1100 Series User’s Manual Installation and Configuration Installation with an installation package for Win CE 5.0 In this section, we show how t o install the Moxa WinCE 5.0 dri ver on a Windows C E 5.0 operating syst em directly . Step 1: Obtain a copy of th e UPo rt 1110/1130/1150 W in CE 5.
UPort 1100 Series User’s Manual Installation and Configuration 2-31.
UPort 1100 Series User’s Manual Installation and Configuration Removing the Moxa WinCE 5.0 / CE 6.0 Driver For WinCE 6.0 Driver: Step 1: Select driver to Remove . Step 2: Switch the folder to C: MOXAUP1100 and double click “ unins000.exe ” to remove installation folder.
UPort 1100 Series User’s Manual Installation and Configuration For WinCE 5.0 Driver: Step 1: In the “OSDesign_View”, delete “USB to Serial Adaptors (Prefi x XXX)”. Step 2: Remove driver from control panel . Step 3: Check “clean before building” Step 4: Use “build and sysgen” to rebuild th e image.
UPort 1100 Series User’s Manual Installation and Configuration 2-34.
UPort 1100 Series User’s Manual Installation and Configuration Step 3: Click on the “Explore” bu tton in the ActiveSync window, and then co p y the UP1100_C OM_v1.0_Setup.C AB (For WinC E 6.0) or UP11 00_COM_v1.1_Set up.CAB (For WinCE 5.0) file to the Mobile/Target Dev ice.
3 3 Chapter 3 Pin Assignment UPort DB9 Pin Assignments The UPort 1100 series uses male DB9 connectors . Pin assign ments are shown in the following diagram: DB9 (male) Pin RS-232 RS-422 4- wire RS-485.
デバイスMoxa Technologies UPORT 1100の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Moxa Technologies UPORT 1100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMoxa Technologies UPORT 1100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Moxa Technologies UPORT 1100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Moxa Technologies UPORT 1100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Moxa Technologies UPORT 1100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMoxa Technologies UPORT 1100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Moxa Technologies UPORT 1100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMoxa Technologies UPORT 1100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
