MultiquipメーカーCDM1Hの使用説明書/サービス説明書
ページ先へ移動 of 32
OPERA TION AND P AR TS MANUAL THIS MANU AL MUST A CCOMP ANY THE EQUIPMENT A T ALL TIMES. T o find the latest revision of this publication, visit our website at: www .
P A GE 2 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) Engine exhaust and some of its constituents, and some dust created of California to cause cancer , birth defects and other repr oductive harm.
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 3 Grinding/cutting/drilling of masonry , concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica.
P A GE 4 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — T ABLE OF CONTENTS Specification and part number are subject to change without notice . Multiquip CDM1H Hand-Held Core Drill Proposition 65 W ar ning .
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 5 CDM1H HAND-HELD CORE DRILL — P AR TS ORDERING PR OCEDURES www .multiquip .
P A GE 6 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) Other impor tant messages are pro vided throughout this manual to help pre vent damage to y our dr ill, other proper ty , or the surrounding environment. CA UTION - Equipment Damage Hazards AL W A YS wear approv ed e ye and hearing protection.
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 7 CDM1H HAND-HELD CORE DRILL — RULES FOR SAFE OPERA TION The following safety guidelines should always be used when operating the MQ Model CDM1H Core Drill. GENERAL SAFETY ■ DO NO T operate or ser vice this equipment before reading this entire manual.
P A GE 8 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — R ULES FOR SAFE OPERA TION ■ Maintain the core drill and dr ill bits with care. K eep drill bits sharp. Sharp cutting edges are less likely to bind.
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 9 TRANSPORTING ■ AL W A YS place the core dr ill inside its carr ying case when work has been completed. ■ AL W A YS wrap pow er cord neatly to av oid damage. ■ AL W A YS place wrenches back into carrying case when work has been completed.
P A GE 10 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — GENERAL INFORMA TION APPLICA TION The MQ CDM1H Hand-Held Core Drill is designed to be used for either dry or wet drilling applications involving con- crete type materials.
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 11 Figure 2. CDM1H Core Drill Dimensions CDM1H HAND-HELD CORE DRILL — SPECIFICA TIONS/DIMENSIONS Contact the MQ Sales Department for the core drill that best fits your application.
P A GE 12 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) 1 . Hand-Grip – The CDM1H uses a plastic hand grip to guard against possible electric shock. When dr illing, hold this gr ip firmly . 2 . Reset Button – In the event of an overload press this button.
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 13 CDM1H HAND-HELD CORE DRILL — PRE-SETUP Before Starting: CA UTION - Read Manual Before attempting to operate this core drill, and to avoid serious injury to personnel, always read and understand operation manual.
P A GE 14 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — PRE-SETUP Attaching the Cobra™ Core Bit to the Core Drill 1 . Place the core bit and core drill on a suitable workbench or area that is free of clutter dirt and debris.
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 15 Applying Power to the Core Drill 1. This core drill requires 115 V A C, 60 Hz po wer . Applying power to the drill that is not specified will cause severe damage to the core drill.
P A GE 16 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — OPERA TION Before Operating 1. Place the valve on the water source to the ON position, and then turn the water valve on the core drill (Figure 8) to the ON position (down).
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 17 CDM1H HAND-HELD CORE DRILL — SHUTDO WN/MAINTENANCE Shutdown 1. Remove the power cord from the wall receptacle or power source. 2. Allow a sufficient amount of time for the core drill bit to cool before attempting to remove it from the core drill.
P A GE 18 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — TR OUBLESHOO TING G N I T O O H S E L B U O R T L L I R D E R O C . 4 E L B A T M O T P M Y S M E L B O R P E L B I S S O P N O I T U L O S .
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 19 CDM1H HAND-HELD CORE DRILL — WIRING DIA GRAM.
P A GE 20 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CORE DRILL — EXPLANA TION OF CODE IN REMARKS COLUMN The f ollowing section e xplains the diff erent symbols and remarks used in the P ar ts section of this manual.
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 21 CDM1H Hand Held Core Drill 1 to 5 Units Qt y . ..... P/N ......................... Description 2 ......... CD 101534 ............... CARBON BR USH 2 ......... CD 101560 .
P A GE 22 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — NAMEPLA TE AND DECALS NAMEPLA TE AND DECALS.
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 23 CDM1H HAND-HELD CORE DRILL — NAMEPLA TE AND DECALS NAMEPLA TE AND DECALS NO .
P A GE 24 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — CORE DRILL ASSY . CORE DRILL ASSY .
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 25 CORE DRILL ASSY . NO . P AR T NO . P AR T NAME QTY . REMARKS 1 CD101501 GEAR CASE 1 2 CD101502 MAIN SHAFT 1 3 CD10150.
P A GE 26 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL — CORE DRILL ASSY . CORE DRILL ASSY .
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 27 CORE DRILL ASSY . (CONTINUED) NO . P AR T NO . P AR T NAME QTY . REMARKS 4 5 CD101545 SPRING 1 4 6 CD101546 SHIFTER 1 4 7 CD101547 SCREW , M6 1 4 8 CD101548 N U T , M 6 2 4 9 CD101549 SCREW , M6 1 5 0 CD101550 SWITCH BO X .
P A GE 28 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) CDM1H HAND-HELD CORE DRILL —CARR YING CASE /T OOLS/AD APTER CARR YING CASE/T OOLS AD APTER 2 6 3 5 4 T OOL KIT.
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 29 CDM1H HAND-HELD CORE DRILL —CARR YING CASE /T OOLS/AD APTER CARR YING CASE/T OOLS AD APTER NO .
P A GE 30 —CDM1H CORE DRILL — OPERA TION AND P ARTS MANU AL — REV . #6 (09/08/10) TERMS AND CONDITIONS OF SALE —P AR TS P A Y MENT TERMS T er ms of payment for parts are net 3 0 days. FREIGHT P OLIC Y All parts orders will be shipped collect or prepaid with the c harges add ed to the invoice.
CDM1H CORE DRILL — OPERATION AND PARTS MANUAL — REV. #6 (09/08/10) — PAGE 31 NO TES.
OPERA TION AND P AR TS MANUAL Y our Local Dealer is: HERE’S HOW TO GET HELP PLEASE HA VE THE MODEL AND SERIAL NUMBER ON-HAND W HEN CALLING © COPYRIGHT 2010, MUL TIQUIP INC . Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without w ritten permission.
デバイスMultiquip CDM1Hの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Multiquip CDM1Hをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMultiquip CDM1Hの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Multiquip CDM1Hの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Multiquip CDM1Hで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Multiquip CDM1Hを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMultiquip CDM1Hの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Multiquip CDM1Hに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMultiquip CDM1Hデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
