MustekメーカーTP-6000の使用説明書/サービス説明書
ページ先へ移動 of 27
TOUCH PANEL POS SYSTEM Rev. : A1 TP-6000 SERIES USER’S MANUAL.
CMANUTP6000-2 SOME IMPORTANT NOTES FCC NOTES This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications.
i TABLE OF CONTENTS BRIEF INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 THE USER’S MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 THE PRODUCT . . . . . . . . . . . . . . . . . . .
ii INSTALLING CASH DRAWERS . . . . . . . . . . . . . . . . . . . . . . . . 3 - 6 WALL MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 7 LOCATION FOR INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 3 - 7 USING THE TOUCH POS .
TP6000 USER’S MANUAL 1 - 1 BRIEF INTRODUCTION THE USER ’ S MANUAL The purpose of this manual is to guide the user in the initial installation and general use of the Posiflex fully integrated compact touch terminal system with touch panel input. TP6000 series is a product group of fully integrated PC based touch terminal systems.
TP6000 USER’S MANUAL 1 - 2 f) Height adjustment: the high / low adjustment gives 20 mm difference in height g) Resistive type touch panel h) Extra long life touch panel that endures 10 million up to.
TP6000 USER’S MANUAL 1 - 3 q) Touch control functions : left/right mouse buttons, double click, drag & drop r) Touch sound can be pitch adjusted and enabled/disabled by software control s) High .
TP6000 USER’S MANUAL 1 - 4.
TP6000 USER’S MANUAL 2 - 1 PARTS IDENTIFIC ATION FRONT VIEW The MSR unit is optional for both 12” and 15” models. The orange/green LED in the logo area is multipurpose. Please refer to the paragraph discussing the LED indication in the “USING THE TOUCH POS” chapter of this manual.
TP6000 USER’S MANUAL 2 - 2 SIDE VIEWS Right Side Vie w Left Side Vie w Lock/Release Lever Push In This Direction To Adjust The Tilt Angle Of The Display Panel Slide Switch For Power On/Off Control P.
TP6000 USER’S MANUAL 2 - 3 REAR VIEW REAR VIEW OF MAIN UNIT Note: The contents in the service window may evolve as technology progresses. Please consult your dealer for applicability.
TP6000 USER’S MANUAL 2 - 4 ADJUSTABLE STAND ASSEMBLY BOTTOM OF STAND ASSEMBLY Base Matching Holes Stand Lock/Release Lever Lock/Release Button For Main Unit Cable Exit Cable Passage Cover UPS Batter.
TP6000 USER’S MANUAL 3 - 1 INS TALLATION GUIDES CAUTION: Before installing any cables or peripherals to the terminal, please always make certain that the system is turned off and the external power .
TP6000 USER’S MANUAL 3 - 2 Cable Passage Cover Cable Passage Four Screws Holding Battery Cover Battery Cover PREPARING STAND ASSEMBLY Take the adjustable stand assembly and turn it up side down to show the bottom of the base.
TP6000 USER’S MANUAL 3 - 3 INSTALLING UPS BATTERY Place the optional UPS battery in the battery compartment (shown top left). Screw on the battery cover and route the battery cable through the base. Please enable the UPS features in the software settings before use.
TP6000 USER’S MANUAL 3 - 4 PREPAR ING THE MAIN UNIT On the back of the main unit, there are 4 matching pegs and a service window. Push the service window open, in the direction indicated in the picture. Below, one can find a button cell battery socket, a 1 x 3 header (JP10) with 1 jumper and a 2 x 3 header (JP8) with 2 jumpers.
TP6000 USER’S MANUAL 3 - 5 toward the upper round part of the hole and make sure that all pegs have been properly seated. Then slide the main unit down to move the pegs into the narrow section of the slot until the rear latch clicks.
TP6000 USER’S MANUAL 3 - 6 CONNECTING CABLES Connect the required cables to the appropriate connectors. Please make sure that each connector is connected to the right port with the correct orientation.
TP6000 USER’S MANUAL 3 - 7 marked “signal cable from POS Printer” at the rear of each cash drawer. The cable lengths for the two 8 pin plugs are different. Use the shorter one for the first cash drawer “CR1” and use the longer one for the second cash drawer “CR2” that will be controlled by the application software.
TP6000 USER’S MANUAL 3 - 8 be either 360 mm or 380 mm depending on the adjusted position. When the main unit is tilted to near horizontal position, the total height required is 275 mm.
TP6000 USER’S MANUAL 4 - 1 USING THE TOUCH POS APPLICATION ENVIRONMENT It is very important that you check the following operational guidelines: Ventilation This terminal must NOT be operated in an environment with restricted ventilation.
TP6000 USER’S MANUAL 4 - 2 Serial Port – COM1 CAUTION: The COM1 serial port should be occupied by either a suitable serial device or a COM1 terminator at all times (as supplied). Without this provision the cash drawer control ports will fail to work correctly.
TP6000 USER’S MANUAL 4 - 3 Ÿ When the external power fails and the TP6000 is working on the optional UPS battery power, the green LED flashes. Ÿ When the optional UPS battery is close to full discharge from supporting the TP6000 in the absence of the external power, the orange LED flashes rapidly.
TP6000 USER’S MANUAL 4 - 4 Software Support The TP6000 series provides a software power off command for application program maneuvers. The TP6000 also provides a specific means for the software to detect if the system is working on external or UPS battery power.
TP6000 USER’S MANUAL 4 - 5 MAGNETIC STRIPE READER The magnetic stripe reader, if installed, will be mounted on the right edge of the TP6000 series. When reading an ISO standard magnetic card, please face the magnetic stripe toward the TP6000 series and slide the card downward through the slot.
TP6000 USER’S MANUAL 4 - 6 TOUCH PANEL The touch panel in TP6000 series uses either a PS2 interface or an RS232 interfaced. When its driver is properly installed, this touch panel works exactly like a standard mouse.
TP6000 USER’S MANUAL 4 - 7 This program controls software gating of data read from each MSR track and the way that the data is sent from the reader to the system, including the coding method against language systems, data transmission speed, delivery and selection on the leading/ending code of each track.
デバイスMustek TP-6000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Mustek TP-6000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはMustek TP-6000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Mustek TP-6000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Mustek TP-6000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Mustek TP-6000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はMustek TP-6000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Mustek TP-6000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちMustek TP-6000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。