Nady SystemsメーカーSW-1KUの使用説明書/サービス説明書
ページ先へ移動 of 24
8W - 1 KU 1000-Channel UHF Dual Receiver Wireless System OWNER’S MANUAL.
Contents 2 Introduction ............................................................................................................................. 2 Using this Manual .................................................................................
System Features 8W-1KU System • Unsurpassed state-of-the-art PLL UHF performance with 120dB dynamic range and operation up to500 ft. line-of-sight • 1000 user -selectable UHF frequencies per band 8W-1KU Octo Receiver • Unsurpassed state-of-the-art PLL UHF performance with 120dB dynamic range and operation up to 500 ft.
4 Quick User Controls Guide 8W-1KU Receiver: Front V iew 1. POWER BUTTON Press for two seconds to turn receivers ON-OFF 2. DIVERSITY A/B INDICA TOR Indicates receiver A or B is active when transmitter is on 3. AF PEAK LED Shows flickering GREEN LED is normal or solid GREEN LED is for maximum audio allowable 4.
Quick User Controls Guide 8W-1KU Receiver: Rear V iew 5 13. RACK EARS Left and Right rack ears are built into the unit 13a. FAM-K2 ANTENNA EXTENSION CABLES (Optional) Attach coax cables with BNC connectors from back antenna jack to rack ear holes for front antenna mounting configuration 14.
6 Quick User Controls Guide HT -1KU Handheld T ransmitter 22. BA TTERY COVER Unscrew CW and pull down to insert two AA alkaline batteries 23. MIC BALL Windscreen/dust cover 24. LCD DISPLA Y For indication of GRP (00-09)/ CH (00-99), AUDIO INPUT LEVEL (0dB to -30dB), and BA TTERY status (5 bars and “BA TT .
7 Quick User Controls Guide BT -1KU Bodypack T ransmitter (L T , L T/HM or GT) 37. INPUT JACK 3.5mm locking mini jack for connecting audio input cord from lapel mic (L T), Headmic™ (L T/HM), or instrument (GT) 38. POWER OFF/MUTE/ON SWITCH Slide power switch to ON or OFF to turn ON-OFF , set to MUTE to turn power on with audio muted 39.
Installing Antennas Install antennas on back by connecting the two Antennas (21) included with your system onto the two RF Connectors (14/19) located on the back of the 8W-1KU receivers. The two antennas must be installed in order for the diversity circuit to work properly .
9 During manual programming, the selected function will flash for five seconds or press the Set button to confirm the selection and the display will return to the main menu.
will flash for five seconds or press the Set button to confirm the selection and the display will return to the main menu. For detail how to IR Sync the TX, see IR Sync Programming in Programming sections of HT -1KU and BT -1KU transmitter sections.
11 Y our 8W-1KU receiver is now operational and ready to use. Once you have completed the above steps, proceed to the following instructions for the HT -1KU Handheld or BT - 1KU Instrument transmitter . Note: Only one transmitter can be used with one receiver .
HT -1KU Handheld Microphone T ransmitter Setting up the T ransmitter The HT -1KU requires two AA size batteries to operate. T o install the batteries onto the battery compartment, unscrew the Battery Compartment Cover (22) by turning counterclockwise until loose and slide down the cover , exposing the Battery Compartment (35).
13 IR Sync Programming: Use the wireless IR LED Receptor Sensor (34) to download pre-programmed channels from the receiver . Start programming by holding the IR Receptor Sensor/Window about 6” in front the receiver to be used.
14 decrease the RF power (reduced range). This is a useful feature as the “L” setting increases battery life and also optimizes the number of channels that can be used simultaneously in a given location. Use this setting for normal use not requiring maximum operating range.
15 should stay lit as possible, indicating usable battery strength. As the batteries weaken, fewer of the level indicators stay lit until only one bar shows, which will then flash to warn that the batteries are now too low and should be replaced as soon as possible.
16 at -10dB for L T/HM and 0dB for GT . These settings are optimal for most applications. For normal operation, the transmitter should have the same Group/Channel as displayed on the receiver .
17 Specifications SYSTEM OVERALL SPECIFICA TIONS Operating Frequency Range (U.S.) Band 1: 672.000-696.975MHz, (Int.) Band 2: 795.000- 819.975MHz Freq. Synthesized (1000 channels switchable) 25kHz/ step PLL System Frequency Stability <0.005% Frequency Response 30Hz-18kHz +/-3dB Dynamic Range 120dB Harmonic Distortion <0.
18 LCD Display Group/ Channels/ Input V olume/ Battery Levels Antenna T ype External fixed Battery T ype 2 x AA alkaline batteries operation Battery Life 8-10 Hours typical Dimensions 2.5”W x 3.25”H x 1-13/16”D (6.35cm x 8.3cm x 1.82cm) Weight (w/o batteries) 3.
19 Feedback A void acoustic feedback (howling or screeching) by taking care in selecting P A volume, transmitter location and speaker placement. Please also note the pickup pattern characteristics of the microphone selected. Unidirectional mics are more resistant to feedback.
• For optimal operation with external antennas, low loss RF shielded cable should be used and the length of the cable should not exceed 10 ft. (3 m). • The receiver antennas should be kept away from any metal surfaces whenever possible as they can reflect away or shield the incoming RF signal.
• When using the BT -1KU bodypack for instrument use: Scratchy noises can sometimes occur when an electric guitar with dirty pots or connections is used with a wireless system. Therefore, the supplied capacitor provides first-order filtering of the RF signal from the cord into the guitar and eliminates virtually all scratchy noises.
Frequency Frequency Plan Band 1 (U.S.): 672.000-696.975MHz Band 2 (International): 795.000-819.975MHz 25KHz per step (1000 Channels) U.S. The 8U-1KU System Includes: User’ Manual (This manual) Main .
One Y ear Limited Warranty Nady Systems, Inc. warrants to the original consumer purchaser that the unit is free from any defects in material or workmanship for a period of one year from the date of original retail purchase. If any such defect is discovered within the warranty period, Nady Systems, Inc.
6701 Shellmound Street | Emeryville, CA USA 94608 T 510.652.2411 | F 510.652.5075 | www .nady.com 07/11.
デバイスNady Systems SW-1KUの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Nady Systems SW-1KUをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNady Systems SW-1KUの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Nady Systems SW-1KUの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Nady Systems SW-1KUで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Nady Systems SW-1KUを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNady Systems SW-1KUの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Nady Systems SW-1KUに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNady Systems SW-1KUデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
