National Instrumentsメーカー7604の使用説明書/サービス説明書
ページ先へ移動 of 31
National Instruments™, NI™, and ni.com™ are t rademarks of National Instruments Corporation. Product and company names mentioned herein are trademarks or tra de names of their respectiv e companies. 322454C-01 Copyright © 1999, 2001 National Instr uments Corp.
MID-7604/7602 Power Drive 2 ni.com Technical Support Resources ............. ............... ........... .............. .............31 NI Web Support......................... ........... ........... .............. ............ .......31 Worldwide Support .
© National Instruments Corporation 3 MID-7604/7602 Power Drive • Connect the equipment into an outlet on a circuit diffe rent from that to which the rec eiver is connected.
MID-7604/7602 Power Drive 4 ni.com Introduction National Instruments ’ MID-7 604/7602 power dri ve is a complete po wer amplifier and system interface for use with four or two axes of simultaneous stepper motion c ontrol.
© National Instruments Corporation 5 MID-7604/7602 Power Drive ❑ One of the follo wing shielded cable assemblies, as applicable: – SH68-C68-S (part number 186381 -02) – SHC68-C68-S (part number 186380-02) Deta i l ed speci f i ca t ions f o r t he MID- 7 604 / 76 0 2 a re in the S p ecif i c a ti o ns section in this guide.
MID-7604/7602 Power Drive 6 ni.com • Pollution D egree 2 — Normally only noncon ductiv e pollu tion occurs. Occasionally , noncon ducti ve pollution becomes conducti ve because of condensation. • Pollution D egree 3 — Conductiv e poll ution or dry , n onconductiv e pollution occurs.
© National Instruments Corporation 7 MID-7604/7602 Power Drive The following is a diagram of a sample installati on. Warning The stepper motor connectors on this dri ve are energized when the unit is powered on. Disconnect the MID-7604/7602 unit from t he po w er outlet before connecting wires to or disconnecting wires from the stepper connectors.
MID-7604/7602 Power Drive 8 ni.com The two rock er switches on the MID-7604/7602 front panel are the A C POWER and EN ABLE. Figure 1 sho ws the location of these switch es. The A C PO W ER switch energizes the motor bus (+24 V) and the logic (+5 V) pow er supplies.
© National Instruments Corporation 9 MID-7604/7602 Power Drive Caution Be sure to turn off the EN ABLE switch and the main A C power to your MID-7604/7602 and host comput er before connecting the accessory to your motion controller . Warning The stepper motor connectors on this dri ve are energized when the unit is powered on.
MID-7604/7602 Power Drive 10 ni.com If the DC power supplies are acti ve, the green po wer LED illuminates. If this LED fails to illuminate, check the power cord and the main input fuse on the f ront panel. The LED status array is arranged b y motor axes.
© National Instruments Corporation 11 MID-7604/7602 Power Drive Front Panel DIP Switch Settings The MID-7604/7602 front panel has a detachable metal plate that when remov ed provides access to four 10-position DIP switch banks. Refer to Figure 1 for the location of t hese switches.
MID-7604/7602 Power Drive 12 ni.com Microstepping Selection The MID-7604/7602 uses bipolar chopper, tw o -phase microsteppi ng dri vers with a broad range of microstep rates. The factory default setting is 10-times microstepping (2,000 steps/rev with standard 1.
© National Instruments Corporation 13 MID-7604/7602 Power Drive Output Current Settings The MID-7604/7602 can provide 0.20 – 1.4 A peak (0.14 – 1AR M S ) , depending on the peak output current DIP switch settings for each axis. DIP switches 1 through 4 control the peak o utput current.
MID-7604/7602 Power Drive 14 ni.com T o determine the maximum total power dissipation of all of the m otors combined, add up the maximum po wer each motor can dissipate. If this v alue is less than or equal to 80 W continuous, you will not exceed the capabilities of the MID -7604/7602.
© National Instruments Corporation 15 MID-7604/7602 Power Drive Inhibit Input Polarity Setting The MID-7604/7602 has a DIP switch that globall y sets the polarity f or the inhibit input for all axes. DIP switch 10 on the axis 1 DIP switch ban k controls this setting.
MID-7604/7602 Power Drive 16 ni.com Back Panel Connector Wiring Motor Power T erminal Blocks Each axis on the MID-7604/7602 has a separat e 5-position remov able scre w terminal block for motor power wiring. Figure 4 sho ws a typical stepper motor configuration pin assignment.
© National Instruments Corporation 17 MID-7604/7602 Power Drive Caution Ne ver connect unused cent er taps or winding terminals to pin 3 ( ground) or to each other . Encoder T erminal Blocks For quadrature incremental encoder signals, each MID-760 4/7602 axis has a separate 8-position remov able screw terminal block.
MID-7604/7602 Power Drive 18 ni.com If the encoder cable length is great er than 10 ft, use encoders wit h line dri ver outputs for your applicatio ns. Po wer for a +5 V encoder — generated by a po wer supply inside the M ID-7604/760 2 — is a vailable on pin 7 .
© National Instruments Corporation 19 MID-7604/7602 Power Drive Figure 8 shows clockwise and counter- clockwise motor rotatio n. Figure 8. Clockwise and Counter -Clockwise Motor Rotation When connecting the enco der wiring to your MID-7604 /7602, use shielded wire of at least 24 A WG.
MID-7604/7602 Power Drive 20 ni.com Limit Switch T erminal Blocks For end-of-tra vel limit, home, inhibit in put, and inhibit output connecti ons, MID-7604/7602 axes hav e a separate, 6-position removable scre w terminal connector block. Figure 10 shows the limit switch terminal block pin assignments.
© National Instruments Corporation 21 MID-7604/7602 Power Drive Figure 11. T rigger T erminal Block Pin Assignment Figure 12. Breakpoint T erminal Block Pin Assignment Analog I/O T erminal Blocks The MID-7604/7602 has two analog I/O connectors.
MID-7604/7602 Power Drive 22 ni.com Accessories for Optional Use Strain-Relief Bar The strain-relief bar provid es strain relief for wiring t o the back panel terminals of the MID-7604 /7602. The arms of the strain-relief bar attach to the s ides of the MID-76 04/7602 with the thumb nuts facing upward, as shown in Figure 15.
© National Instruments Corporation 23 MID-7604/7602 Power Drive Panel-Mount Kit (Included) The panel-mount kit allows you to m ount the MID-7604/7602 i nside a cabinet or enclosure. Using the provided screws, attach the panel-mount kit to the rear and front set of screw holes on the side p anels of the MID-7604/7602, as sh own in Figure 16.
MID-7604/7602 Power Drive 24 ni.com Stepper Motor Configurations This section describes the various industry-stand ard winding configurations for stepper motors and sho ws how to connect them to a MID-7604/7602. The MID -7604/7602 is compatible with all configurations of two-phase stepper motors.
© National Instruments Corporation 25 MID-7604/7602 Power Drive For maximum fle xibility , y ou can connect 8-wire stepper motors in either a series or parallel configuration.
MID-7604/7602 Power Drive 26 ni.com Notice that an 8-wire motor wired in series is virtually identical to a 6-wire motor and typically has the same high-torque b ut lo w-speed characteristics.
© National Instruments Corporation 27 MID-7604/7602 Power Drive Specifications The follo wing specifications apply only to the MID-7604/7602. T o obtain a system specification, you must account for your motion controller . Refer to your controller specifications to determine o verall system specifications .
MID-7604/7602 Power Drive 28 ni.com Inhibit Inputs Voltage range ........................ ..................0 – 12 VDC Inhibit low voltage ................... ...............0.8 V Inhibit high voltage ........................ .........2 V Inhibit Output Voltage range .
© National Instruments Corporation 29 MID-7604/7602 Power Drive Breakpoints ............ ......................... ....... 6-position m ini-combicon 3.81 mm plug (1 total) Triggers ............ ............... .............. ......... 6-position mini-combicon 3.
MID-7604/7602 Power Drive 30 ni.com Environment Operating temperature ................... ......... 0 to 40 º C (32 to 104 º F) Storage temperature .............. .................. – 20 to 70 º C( – 4t o1 5 8 º F) Humidity ...................
© National Instruments Corporation 31 MID-7604/7602 Power Drive T echnical Support Resources NI We b Support National Instruments W eb support is yo ur first stop for help in solving installation, configuration, and application problems a nd questions.
デバイスNational Instruments 7604の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
National Instruments 7604をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNational Instruments 7604の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。National Instruments 7604の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。National Instruments 7604で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
National Instruments 7604を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNational Instruments 7604の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、National Instruments 7604に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNational Instruments 7604デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
