NetgearメーカーReadyNAS 4220Xの使用説明書/サービス説明書
ページ先へ移動 of 67
350 East Plumeria Drive San Jose, C A 95134 USA Mar ch 2015 202-11272-05 NE T GE AR R eadyNAS OS 6 Rack- Mount S t or age S yst ems Har dwar e Manual Models : R eadyNAS 2120 R eadyNAS 2120 v2 R eadyNA.
2 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems Suppor t Thank you f or pur chasing this NET GE AR pr oduct . After inst alling your device, loc ate the serial number on the label of your pr oduc t and use it to r egist er your pr oduct at https ://my .
3 Cont ents Chapter 1 Getting Started Additional Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Setup Loc ation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Chapter 5 Disks Disk T r ay . . . . . . . . . . . . . . . . . . . . . . .
5 1 1. Getting S t ar t ed Congratulations on your purchase of a NETGEAR ReadyNAS ® storage system. This manual describes the physical features of the ReadyNAS OS 6 rack-mount storage systems.
Getting Started 6 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems Additional Documentation For detailed information about configuring, managing, and using your ReadyNAS storage system, see the ReadyNAS OS 6.2 Software Manual , which is available at http://support.
Getting Started 7 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems Suppor ted Oper ating Syst ems The ReadyNAS storage system is supported on the following systems: • Microsoft Windows 8 • Microsoft Windows 7 • Apple OS X 10.
8 2 2. R eadyNAS 2120 and 2120 v2 This chapter describes the physical features of the ReadyNAS 2120 and the 2120 v2. It includes the following sections: • Front Panel • Rear Panel • Status Infor.
Re adyNAS 2120 and 2120 v2 9 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems Fr ont P anel The following figure shows the front panel of the ReadyNAS 2120 and 2120 v2. 1 2 3 3 5 4 6 Figure 1. Front panel 1. Drive bays 2. Control panel 3. Mounting bracket 4.
ReadyNAS 2120 and 2120 v2 10 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems R ear P anel The following figure shows the rear panel of the ReadyNAS 2120 and the 2120 v2. 12 34 5 6 Figure 3. Rear panel 1. Power cable socket 2. Power switch 3. Disk exhaust fans 4.
Re adyNAS 2120 and 2120 v2 11 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems St atus Inf ormation You can obtain information about the status of your ReadyNAS 2120 or 2120 v2 by reviewing the LEDs listed in the following table.
Re adyNAS 2120 and 2120 v2 12 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems P ow er On and Shut Down This section describes how to power on and shut down your system. If you must shut down the system, use one of the preferred shutdown methods whenever possible.
Re adyNAS 2120 and 2120 v2 13 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems P ower S tat e If the power supply is interrupted due to a power failure, the system returns to its last state once t.
ReadyNAS 2120 and 2120 v2 14 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems • T est disk . Performs an offline full disk test. This process can take four hours or more, depending on the size of your disks. Any problems are reported in the system logs, which you can view using the local admin page.
Re adyNAS 2120 and 2120 v2 15 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems Rack Mounting Y ou can rack-mount the ReadyNAS 2120 and 2120 v2 using the included rack-mount ears. Alternatively , you can use the optional sliding rail kit, order number RRAIL04-10000S.
Re adyNAS 2120 and 2120 v2 16 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems.
17 3 3. R eadyNAS 3130 This chapter describes the physical features of the ReadyNAS 3130. It includes the following sections: • Front Panel • Rear Panel • Status Information • Power On and Shu.
ReadyNAS 3130 18 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems Fr ont P anel The following figure shows the front panel of the ReadyNAS 3130. Figure 4. Front panel 1. Drive bays with disk status LEDs 2. Control panel The following figure shows the control panel in more detail.
Re adyNAS 3130 19 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems Each drive bay features a latch that releases the pop-out tray handle, as shown in the following figure. 2 1 3 4 Figure 6. Drive bay 1. Disk tray handle 2. Disk Present LED 3. Disk tray release latch 4.
ReadyNAS 3130 20 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems R ear P anel The following figure shows the rear panel of the ReadyNAS 3130. 3 4 6 5 1 2 7 8 Figure 7. Rear panel 1. Power cable socket 2. Reserved for NETGEAR support 3. Unit Identifier button 4.
Re adyNAS 3130 21 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems St atus Inf ormation Y ou can obtain information about the status of your system by reviewing the indicators listed in the following table. T able 2. Status indicators Indicator Description Power LED (control panel) The Power LED indicates these states: • Green .
Re adyNAS 3130 22 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems UI LED (rear panel) The UI (Unit Identification) LED indicates these states: • Blue . Software or manual identification is on. • Off . Identification is not requested by software or manually when the UI button is pressed.
Re adyNAS 3130 23 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems P ow er On and Shut Down This section describes how to power on and shut down your system. If you must shut down the system, use one of the preferred shutdown methods whenever possible.
Re adyNAS 3130 24 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems P ower S t at e If the power supply is interrupted due to a power failure, the system returns to its last state once the power supply is restored, as follows: • If the system was powered on at the time of the power failure, the system powers on when the power supply is restored.
Re adyNAS 3130 25 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems • T est disk . Performs an offline full disk test. This process can take four hours or more, depending on the size of your disks. Any problems are reported in the system logs, which you can view using the local admin page.
Re adyNAS 3130 26 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems Rack Mounting Y ou can rack-mount the ReadyNAS 3130 using the included rack-mount ears. Alternatively , you can use the optional sliding rail kit, order number RRAIL04-10000S. For instructions see the 1U Rail Installation Guide, which is available at http://support.
27 4 4. R eadyNAS 3220 and 4220 This chapter describes the physical features of the ReadyNAS 3220 and ReadyNAS 4220. It includes the following sections: • Front Panel • 3220 Rear Panel • ReadyNA.
ReadyNAS 3220 and 4220 28 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems Fr ont P anel The following figure shows the front panel of the ReadyNAS 3220 and 4220. RN3220 1 2 Figure 8. Front panel 1. Drive bays with disk status LEDs 2. Control panel The following figure shows the control panel in more detail.
Re adyNAS 3220 and 4220 29 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems Each drive bay features a latch that releases the pop-out tray handle, as shown in the following figure. 2 1 Figure 10. Disk tray handle and release latch 1. Disk tray handle 2.
ReadyNAS 3220 and 4220 30 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems R eadyNAS 3220 R ear P anel The following figure shows the rear panel of the ReadyNAS 3220. USB eS ATA1 eS ATA2 LAN4 LAN2 LAN3 LAN1 UID CONSOLE PSU 1 PSU 2 3 4 6 5 1 2 7 Figure 1 1.
Re adyNAS 3220 and 4220 31 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems R eadyNAS 4220 R ear P anel The following figure shows the rear panel of the ReadyNAS 4220. USB LAN4 LAN2 LAN3 LAN1 CONSOLE eS ATA1 eS ATA2 UID PSU 1 PSU 2 3 4 6 5 1 2 7 8 Figure 12.
ReadyNAS 3220 and 4220 32 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems St atus Inf ormation Y ou can obtain information about the status of your system by reviewing the indicators listed in the following table. T able 3. Status indicators Indicator Description Power LED (control panel) The Power LED indicates these states: • Green .
Re adyNAS 3220 and 4220 33 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems Boot Menu Use the boot menu to restart or troubleshoot your ReadyNAS storage system. Y our storage system provides the following boot modes: • Normal . Initiates a normal boot process, just like booting using the Power button.
ReadyNAS 3220 and 4220 34 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems The system powers on. 4. Continue to press the Reset button until the Power , UI, and Health LEDs are blinking. Note: It takes approximately one minute for the system to enter boot mode.
Re adyNAS 3220 and 4220 35 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems Rack- Mount Setup Use the rack-mount hardware included with your ReadyNAS 3220 or 4220 to install it in a rack. Read Rack-Mount Precautions on page 67. DANGER: A system with installed drives can weigh more than 80 pounds.
ReadyNAS 3220 and 4220 36 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems 3. Use the provided mounting screws to mount the inner rails to the system chassis, as follows: a. Fasten the backs of the outer rails to the rack with screws. b. Press the release to extend the rails.
37 5 5. Disks This chapter describes how to reformat, add, and replace disks in your ReadyNAS OS 6 storage system. For information about configuring disks on your storage system, see the ReadyNAS OS 6.2 Software Manual , which is available at http://support.
Disks 38 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems Disk T r ay The following figure shows the features of the disk tray . 1 7 23 5 6 4 Figure 13. Disk tray 1. Disk tray handle 2. Disk tray release latch 3. Fault LED 4. Disk Activity LED 5. Disk screw holes (for 3.
Disks 39 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems Suppor ted Disks Use only supported SA T A hard disk drives (HDDs) or solid-state drives (SSDs) in your ReadyNAS storage system. If you use disks that are not supported, NETGEAR technical support will not provide assistance.
Disks 40 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems 3. Reset the system to its factory default settings. W ARNING: This process erases all data and reformats all disks into a single X-RAID volume.
Disks 41 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems Add a Disk Y ou can add a 3.5-inch hard disk drive, 2.5-inch hard disk drive, or a 2.5-inch solid-state drive to an empty disk bay . If you want to add a previously formatted disk to your storage system, see the instructions in Previously Formatted Disks on page 39.
Disks 42 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems 4. Remove the plastic air blocker from the disk tray . 5. Place the new 3.5-inch HDD in the disk tray . 6. Secure the HDD in the tray using the screws that came with your storage system. Make sure that the hard disk connectors face the interior of the disk tray when you assemble the disk.
Disks 43 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems The disk tray is secured in the drive bay . 9. If necessary , turn on your system by pressing the Power button.
Disks 44 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems T o add a 2.5-inch hard disk drive (HDD) or 2.5-inch solid-state drive (SSD): 1. Determine whether you need to shut down your system: • If you are adding disks to a diskless system, gracefully shut down the system.
Disks 45 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems 6. Secure the drive in the tray using the screws that came with your storage system. Make sure that the hard disk connectors face the interior of the disk tray when you assemble the disk. 7.
Disks 46 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems • In a system that uses Flex-RAID, the disk becomes available for use. Y ou use the local admin page to manually configure the new disk. For more information about X-RAID, Flex-RAID, and using the local admin page, see the ReadyNAS OS 6.
Disks 47 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems T o replace a 3.5-inch hard disk drive (HDD): 1. Press the disk tray release latch. The disk tray handle pops out. 2. Pull out the disk tray . 3. Remove the screws and the old 3.5-inch HDD from the tray .
Disks 48 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems 6. Slide the disk tray back into the drive bay of the system. 7. Press the disk tray handle until it latches closed.
Disks 49 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems The disk tray handle pops out. 2. Pull out the disk tray . 3. Remove the screws and the old 2.5-inch HDD or SSD from the tray . 4. Place the new 2.5-inch HDD or SSD in the disk tray . 5. Secure the drive in the tray using the screws.
Disks 50 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems If the volume that contained the failed disk uses a protected RAID configuration, the system automatically resynchronizes the volume using the new disk. Resynchronization might take several hours, depending on the disk size.
51 6 6. Maint enance This chapter describes how to perform maintenance activities like replacing a fan or on-board battery . It includes the following topics: • Access the Inside of the Storage Syst.
Maintenanc e 52 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems Acc ess the Inside of the S t or age S ystem Y ou must access the inside of the system to replace a fan or on-board battery . W ARNING: Ensure that the chassis cover is in place when the system is operating to allow proper cooling.
Maintenanc e 53 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems 4. Lift the top cover from the chassis. Y ou can now access the inside of the system. T o access the inside of a ReadyNAS 3220 or 4220: 1. If your system is mounted in a rack, grasp the two handles on either side and pull the system straight out until it locks.
Maintenanc e 54 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems 4. Lift the top cover from the chassis. Y ou can now access the inside of the system. R eplac e a F an If a fan fails, the remaining fans ramp up to full speed, the Error LED on the control panel lights, and an email alert is sent to the system administrator .
Maintenanc e 55 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems 3. Pull up on the fan gently to remove it from the housing. 4. Remove the four pegs that hold the fan in the housing. 5. Insert the four pegs into holes in the replacement fan. 6. Insert the replacement fan into the housing.
Maintenanc e 56 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems 8. Connect the replacement fan’s power connections. If the system power is on, the hot-plug feature causes the fan to start immediately . T o replace a fan on a ReadyNAS 3220 or 4220: 1.
Maintenanc e 57 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems 3. Squeeze the latches on top of the fan and pull up gently to remove the fan from the housing. 4. Insert the replacement fan into the housing. 5. Connect the replacement fan’ s power connections.
Maintenanc e 58 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems 3. Install the new battery . T ake care to install the new battery with the correct side up. T o replace the battery of a ReadyNAS 3220 or 4220: 1. Open the system and locate the battery holder .
59 A A. Def aults and T echnical Specifications This appendix includes the following sections: • Factory Default Settings • ReadyNAS 2120 and 2120 v2 T echnical Specifications • ReadyNAS 3130 T .
Def aults and T echnical Specifications 60 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems F ac t ory Def ault Settings The following table lists factory default settings for ReadyNAS OS 6 rack-mount storage systems.
Def aults and T echnical Specifications 61 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems • Four-bay storage • T wo E-SA T A ports • One USB 2.0 port (front) • T wo USB 3.0 ports (back) • T wo LAN ports Physical dimensions (h x w x d): • 43.
Def aults and T echnical Specifications 62 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems • 2 GB memory • Four-bay storage • T wo eSA T A ports • One USB 2.0 port (front) • T wo USB 3.0 ports (back) • Four Gigabit LAN ports Physical dimensions (h x w x d): • 44 x 486 x 406 mm (1.
Def aults and T echnical Specifications 63 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems Gener al: • Intel i3-3220, 65W , 3.3 G • 4 GB memory • T welve-bay storage • T wo E-SA T A ports • T wo USB 2.
Def aults and T echnical Specifications 64 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems R eadyNAS 4220 T echnical Specifications The ReadyNAS 4220 storage system meets the following technical specifications: Gener al: • Intel E3-1225V2, 95W , 3.
Def aults and T echnical Specifications 65 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems Saf et y W arnings 1. The equipment contains no operator access areas and is certified for installation only by trained personnel, according to the installation instructions provided with each storage system.
Def aults and T echnical Specifications 66 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age Systems • Do not use mats designed to decrease static electrical discharge as protection from electrical shock. Instead, use rubber mats that were specifically designed as electrical insulators.
Def aults and T echnical Specifications 67 NETGEAR Re adyNAS OS 6 Rack-Mount Stor age S yst ems are generally sufficient to neutralize this dif ference before contact is made to protect your equipment from ESD: • Use a grounded wrist strap designed to prevent static discharge.
デバイスNetgear ReadyNAS 4220Xの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Netgear ReadyNAS 4220Xをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNetgear ReadyNAS 4220Xの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Netgear ReadyNAS 4220Xの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Netgear ReadyNAS 4220Xで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Netgear ReadyNAS 4220Xを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNetgear ReadyNAS 4220Xの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Netgear ReadyNAS 4220Xに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNetgear ReadyNAS 4220Xデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。