Numark IndustriesメーカーTT500の使用説明書/サービス説明書
ページ先へ移動 of 16
CONTENTS Safety Precautions Setup & Installation Controls Cable Setup Platter Setup Inter chan g in g Tonearm Tubes T one Arm S etup Cartrid g e Setup Important Notes & Operation Spec ificat i.
Thank you for purchasing this Numa rk product. Please read thes e operating inst ructions so you wi ll know how to operate t his equipm ent properly. After you have finished reading t hese instructions, keep the m for future reference. WARNING: TO PREVENT FIRE OR SH OCK HAZARD, DO NOT EXPOSE THIS APPLI ANCE TO RAIN OR MOISTURE.
POWER-CORD PROTECTION Power-suppl y cords should be rout ed so that they are n ot likely to be wal ked on or pinched by items placed upon or against the m, paying particular attention to cords a t plugs, convenienc e receptacles, and t he point where they exit from the produ ct.
SETUP & INSTALLATION This turntable has been designed exclusively for DJ use and can be se tup in a variety of different ways depe nding on your mixing style.
CONTROLS General Controls 1. Power Button This button turns on the turntable when pressed. It illuminates blue when the turntable i s switched on. 2. Platter This turntable has a special edge design that has bee n optimized for "dragged" platter slow downs.
CONTROLS c ontinued 9. Pitch Fader This s lide cont rol a llow s the pitch o f th e pl aybac k sou rce t o be changed. In the ce nter position the pitch is at 0%. Moving the fader knob closer to you will increase the pitch. The Pi tch Slider is enclosed in an Interchangeable/Replaceabl e Cartridge.
CONTROLS continued Bottom Parts 20. Adjust able Rubber Dampeni ng Feet When all of the fe et of the turntable ar e completely tig htened, the top flat surface o f the turntable w ill be at 85mm. Unsc rewing these feet rai ses the turnta ble up to compens ate for unlevel ed surfaces.
CABLE SETUP This turntable is sh ipped with two sets of special cables: (1) Right Angle IEC Power Cord (1) Right Angle RCA cord NOTE: Before connecting any cables, make sure that the voltage selector switch is set to the prope r setting! Making the power and audio connections: 1.
PLATTER SETUP WARNING: Incorre ct Platter setup can l ead to poor turn table performance, platte r instability, or permanent motor damage. 1. Start by inspecti ng the bottom of t he aluminum plat ter to check that bot h locking pins have r ubber fitting s on them.
INTERCHANGING TONEARM TUBES WARNING : An incomplete under standing of this procedure could le ad to permanent da mage to the headshe ll, your records, or th e tonearm assembly. NOTICE : Interchanging tonear m tubes unnecessarily m ay shorten the life of the tone arm tubes and/or tonearm component s.
TONE ARM SETUP A properly adjusted tone arm and cartri dge setup will mini mize vinyl recor d wear and optimize th e performance of the turntable. Follo w these simple steps fo r setting the tone arm .
CARTRIDGE SETUP For Head Shell Mounted Cartridges: The cartridge that c omes with this tur ntable should be pre installed on the he ad shell. If it is n't, please follow the below instruct ions for installing a cartridge onto the head shell. 1. Position the head shell an d the cartridge so that th e four connector pins are visible.
OTHER IMPORTANT NOTES Please read these prec autionary notes to in sure a comple te understanding and long life of th is DJ turntable. 1. Unneces sarily remov ing the plat ter may cause d amage to the ma gnet mounti ng structu re, the motor or th e platter resulting in undesired pe rformance.
SPECIFICATIONS Turntable: Torque (transient) : 4.5kgf.cm Torque (stab le): 3.5kgf.cm Motor: Brushless DC motor Brake: Elec tronic braking system Platter: Dampened aluminu m diecast, low frictio n design Pitch: +/-8%, 10%, 25%, 50% Speeds: 33 1/3RPM, 45RP M, 78RPM Wow/flutter: <0.
T ROUBLE SHOOT ING PAGE 14 Turntable does not turn on. Disconnected Power Cord? Connect Power Cord. The sound level is very low. T he Turntable is not co nnected to a device with a PHON O preamp. Connect the device to a preamp DJ mixer or an AV rece iver that has an input labeled PHO NO.
(1) Turntable w /Straigh t Tonearm (1) Anti-Drag A luminum P latte r (1) S -Shaped Tonea rm Tube (1) S -Tube Tone arm Weigh t (1) IEC Power C able (1) Service To o l (1) RCA Cor d (1) Slipma t INSIDE .
デバイスNumark Industries TT500の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Numark Industries TT500をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはNumark Industries TT500の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Numark Industries TT500の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Numark Industries TT500で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Numark Industries TT500を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はNumark Industries TT500の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Numark Industries TT500に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちNumark Industries TT500デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。