OrionメーカーHCCA-D600の使用説明書/サービス説明書
ページ先へ移動 of 21
HCCA-D600 HCCA-D600.
CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 What’ s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION Thank you for your purchase of Orion's HCCA-D600 power amplifier . Each Orion amplifier is designed to be the leader in its class offering the most power , advanced features, and extreme ease of use. In high-end sound systems or high SPL systems, Orion amplifiers will give you years of trouble-free performance.
RECORD YOUR SERIAL NUMBER AND DA TE T o ensure your warranty (see back cover), please record the following information regard- ing your new amplifier .
END P ANEL LA YOUTS 1. RCA Input - accepts RCA input from a head unit, preamplifier , or equalizer . 2. RCA Line Output - provides easy connection to additional amplifiers. 3. Master/Slave Switch - controls whether the amplifier is a slave or master when connected in combined amplifier configurations.
5 © 2005 Directed Electr onics—all rights reserved tem battery . WARNING: Always protect this power wire by installing a fuse or circuit breaker of the appropriate size within 12 inches of the battery terminal connection. 3. REM - this terminal turns on the amplifier when (+) 12 volt is applied.
6 © 2005 Directed Electr onics—all rights reserved SPECIFICA TIONS 1. Continuous 4 W load 20Hz to 250Hz, < 1% THD, with input voltage at 14.4VDC.
7 © 2005 Directed Electr onics—all rights reserved AMPLIFIER SETTINGS Signal Input and Output Configurations The input section of the amplifier consists of a phase switch that sets the output configura- tion, gain controls, and RCA inputs. The input section makes it easy to adapt this amplifier to most system configurations.
8 © 2005 Directed Electr onics—all rights reserved WARNING! DO NOT set crossover frequencies lower than the speakers recommended operating range. This can cause driver failure that is not covered by the man- ufacturer's warranty .
9 © 2005 Directed Electr onics—all rights reserved Infinite Baffle Example High-Pass Set at 30Hz By removing low frequency signal that the woofer cannot produce, the woofer can play its capable range louder . The first example is an infinite baffle situation.
10 © 2005 Directed Electr onics—all rights reserved Sealed Example High-Pass Set at 20Hz This sealed example is the same 12-inch woofer in the recommended sealed enclosure. Up to 6 dB of boost is capable if 20 Hz was used. With +6dB of boost, the woofer has more out- put down to 15 Hz.
11 © 2005 Directed Electr onics—all rights reserved Remote Gain Operation NOTE: Do not use the Remote Gain control when you have an expanded system installed (see Line Ouput Configurations ).
12 © 2005 Directed Electr onics—all rights reserved Bridging For bridging into a single speaker load, this amplifier has the ability to be bridged with another amplifier (must be the same model). T o do this you must utilize the MASTER/SLAVE and PHASE switch settings.
13 © 2005 Directed Electr onics—all rights reserved NOTE: The wiring connections to the power , remote and speaker terminals should be accomplished before the amplifier is mounted. NOTE: Mounting amplifiers upside down is not recommended and may cause premature thermal shutdown.
14 © 2005 Directed Electr onics—all rights reserved Orion amplifiers generate a certain amount of heat as part of normal operation. Be sure the area around the amplifier is unobstructed to allow adequate air circulation.
15 © 2005 Directed Electr onics—all rights reserved Controls and Speaker Connections sections of this guide for correct wiring instructions. Step 9 Mount the amplifier . Make sure the amplifier is mounted on a flat surface. If this is not possible, do not over tighten the screws so that the chassis of the amplifier is twisted or bent.
16 © 2005 Directed Electr onics—all rights reserved Connections and the T roubleshooting Tips sections of this manual to solve your installation problems. Step 6 Check to make sure the output for each channel is correct. If the active crossovers are used, check to make sure that each output is correct from the amplifier .
17 © 2005 Directed Electr onics—all rights reserved T roubleshooting Tips Symptom Probable Cause Action T o T ake No output Low or no remote turn-on Check remote turn-on voltage at voltage amplifier and repair as needed. Fuse blown Check power wire's integrity and check for speaker shorts.
18 © 2005 Directed Electr onics—all rights reserved Symptom Probable Cause Action T o T ake Distorted output Internal crossover not set Readjust crossovers. Refer to the properly for speakers Internal Crossover Configuration section of this guide for detailed instructions.
NOTES ____________________________________________________ ____________________________________________________ ____________________________________________________ ___________________________________.
W arranty LIMITED TWO YEAR CONSUMER WARRANTY : Directed Electronics promises to the original purchaser , to replace this product should it prove to be defective in workmanship or material under normal.
デバイスOrion HCCA-D600の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Orion HCCA-D600をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはOrion HCCA-D600の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Orion HCCA-D600の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Orion HCCA-D600で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Orion HCCA-D600を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はOrion HCCA-D600の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Orion HCCA-D600に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちOrion HCCA-D600デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
