AsusメーカーP4T-Mの使用説明書/サービス説明書
ページ先へ移動 of 19
ASUS P4T -M Quick Setup Manual 1 ® P4T -M Intel ® 850 A TX Motherboard Quick Setup Manual SPECIFICA TIONS AND INFORMA TION CONT AINED IN THIS MANUAL ARE FURNISHED FOR INFORMA TIONAL USE ONL Y , AND ARE SUBJECT TO CHANGE A T ANY TIME WITH- OUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUST eK COMPUTER INC.
2 ASUS P4T -M Quick Setup Manual 1. FEA TURES 1.1 P4T -M Motherboard Layout Motherboard Layout 3. H/W SETUP 24.4cm (9.60in) 24.4cm (9.6in) PS/2KBMS T: Mouse B: K eyboard PCI1 PCI2 PCI3 P ANEL FLOPPY S.
ASUS P4T -M Quick Setup Manual 3 1.2 Layout Contents Expansion 1) RI M M A1/A2/B1/B2 p.18 184-Pin System Memory Support 2) CPU p.19 Central Processing Unit (CPU)6 3) PCI1/2/3/4/5 p.25 32-bit PCI Bus Expansion Slots 4) AGPPRO p.26 Accelerated Graphics Port (AGP Pro) Slot Connectors 1 ) PRIMAR Y/SECONDAR Y IDE p.
4 ASUS P4T -M Quick Setup Manual 2. HARDW ARE SETUP 2.1 Getting Started IMPORT ANT : Due to Pentium 4 CPU’ s power consumption requirement, an A TX12V power supply is recommended for this motherboard. For typical system configurations, an A TX12V power supply that can supply at least 230W and at least 8.
ASUS P4T -M Quick Setup Manual 5 2. HARDW ARE SETUP 2.2 System Memory NOTE: No hardware or BIOS setup is required after adding or removing memory . This motherboard has four 184-pin R ambus I nline M emory M odules (RIMM) sockets. These sockets support 64Mbit, 128Mbit, and 256Mbit Direct RDRAM technologies.
6 ASUS P4T -M Quick Setup Manual 2. HARDW ARE SETUP 2.2.1 Installing Memory The memory module (RIMM/C-RIMM) will fit in only one orientation. IMPORT ANT : Do not touch the memory module’ s connectors. Handle the mod- ule only by the edges. 1. Make sure that the notch keys in the module are aligned with the small ribs inside the RIMM sockets.
ASUS P4T -M Quick Setup Manual 7 2. HARDW ARE SETUP 2.3 Central Processing Unit (CPU) The motherboard provides a ZIF Socket for the supported CPUs. The CPU that came with the motherboard should have a fan attached to it to prevent overheating. If this is not the case, then purchase a fan before you turn on your system.
8 ASUS P4T -M Quick Setup Manual 2. HARDW ARE SETUP 2.3.1 CPU Installation Step 1: Install the Baseboard A metal baseboard is required to install the heatsink to the motherboard. A rubber pad is placed between the metal board and motherboard to provide insulation to prevent shorting.
ASUS P4T -M Quick Setup Manual 9 2. HARDW ARE SETUP Step 2: Install the CPU A. Locate the ZIF socket on the motherboard. B. Unlock the socket by pressing the lever sidesways and then lifting it up to a 90˚–100˚ angle.
10 ASUS P4T -M Quick Setup Manual 2. HARDW ARE SETUP Step 3: Install the Heatsink Support Base Place the two heatsink support base as shown and screw in the four pan head screws. Step 4: Install the Heatsink Carefully place the fan heatsink on top of the heatsink support base and connect the fan power cable to the CPU fan connector .
ASUS P4T -M Quick Setup Manual 11 2. HARDW ARE SETUP Step 5: Install the Heatsink Retaining Clips 1 Latch one end of the heatsink retaining clip to one of the tabs on the heatsink support base. 1 2 3 2 Latch the lar ge slotted tab on the clip to the protrud- ing tab on the side of the heatsink support base.
12 ASUS P4T -M Quick Setup Manual 2. HARDW ARE SETUP 2.4 Expansion Cards W ARNING ! Unplug your power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards (see 3.
ASUS P4T -M Quick Setup Manual 13 2. HARDW ARE SETUP IMPORT ANT : If using PCI cards on shared slots, make sure that the drivers sup- port “Share IRQ” or that the cards do not need IRQ assignments. Conflicts will arise between the two PCI groups that will make the system unstable or cards inoperable.
14 ASUS P4T -M Quick Setup Manual 2. HARDW ARE SETUP 1) Primary (Blue) / Secondary IDE Connectors (T wo 40-1pin IDE) These connectors support the provided IDE hard disk ribbon cable.
ASUS P4T -M Quick Setup Manual 15 3) Chassis (PCI_F AN), CPU (CPU_F AN), Power Supply (MAIN_F AN) Fan Connectors (3 pins) These connectors support cooling fans of 350mA (4.2 W atts) or less. Orientate the fans so that the heat sink fins allow airflow to go across the onboard heat sink(s) instead of the expansion slots.
16 ASUS P4T -M Quick Setup Manual 5) USB Headers (10-1 pin USB2) If the USB Ports on the back panels are inadequate, a USB header is available for two additional USB ports.
ASUS P4T -M Quick Setup Manual 17 6) Internal Audio Connectors ( 4 -pin VIDEO, CD_IN, AUX) These connectors allow you to receive stereo audio input from such audio-vi- sual sources as a VIDEO or CD-ROM input, or MPEG card.
18 ASUS P4T -M Quick Setup Manual 8) Power Supply Connectors (20-pin block A TXPWR) (6-pin AUXPWR) (4-pin A TX12V) These connectors connect to an A TX 12V power supply . Each plug from the power supply will only insert in one orientation because of the dif ferent hole sizes.
ASUS P4T -M Quick Setup Manual 19 P4T-M P4T -M System Panel Connectors * Requires an A TX power supply . PLED Ground MLED PWR +5 V Keylock +5V Speaker Speaker Connector Power LED Ground +5 V Reset SW .
デバイスAsus P4T-Mの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Asus P4T-Mをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAsus P4T-Mの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Asus P4T-Mの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Asus P4T-Mで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Asus P4T-Mを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAsus P4T-Mの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Asus P4T-Mに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAsus P4T-Mデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
