PanasonicメーカーTZ-PCD2000の使用説明書/サービス説明書
ページ先へ移動 of 28
1 Digit al CA TV T erminal Operating Instructions Model No. TZ-PCD2000 For assistance, please call : your regional operator (inst aller) Before connecting, operating or adjusting this product, please read these instructions completely . Save this manual for future reference.
2 The lightning flash with arrow-head within a triangle is intended to tell the user that part s inside the product are a risk of electric shock to persons. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance.
3 Additional Instructions l Power Sources This product shall be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your Cable operator or Digital CA TV T erminal installer or local power company .
4 Additional Instructions l Out door Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up st atic charges.
5 FCC ST A TEMENT FCC INFORMA TION Y our Digital CA TV T erminal is registered with the Federal Communication Commission and is in compliance with CFR47, Parts 15b, FCC Rules and Regulations.
6 Dear Panasonic Customer Welcome to the Panasonic Family of customers. We hope that you have many years of enjoyment from your new Digital CA TV T erminal. T o obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference.
7 Inst allation ACCESSORIES Check the accessories before installations. l Operating Instruction book l AC Power Cord l Remote Control Unit l Battery for the Remote Control Unit (2×AA (IEC R6) size) Remote Control battery inst allation 1. Push the section marked with an arrow while lifting the cover up to open it.
8 Inst allation Front and Rear V iew of the Digit al CA TV T erminal Front Panel POWER indicator(LED) V olume - Button Channel + Button V olume + Button MESSAGE indicator(LED) Display BYP ASS indicator(LED) Power Button Factory use only Channel - Button Factory use only Remote control signal receptor Door Pull the door toward you to open it.
9 Installation Rear Panel AUDIO jacks VIDEO jacks CABLE OUT jack CABLE IN jack AC Switched Outlet DA T A Port USB(Universal Serial Bus) Port S-VIDEO jack DIGIT AL AUDIO OUT BYP ASS option AC Power Inp.
10 Inst allation Cable connection Connect the cable wire to the CABLE IN jack on the rear panel of the Digit al CA TV T erminal. Incoming signal from the Cable Service Provider Digit al CA TV T erminal connection to stereo TV and stereo VCR Follow this diagram when connecting the Digit al CA TV T erminal to a stereo TV and stereo VCR.
11 Digit al CA TV T erminal connection to TV and VCR Installation Follow this diagram when connecting the Digital CA TV T erminal to a TV and VCR. Procedure l Connect the CABLE OUT jack of the Digit al CA TV T erminal to the ANT IN jack of the VCR, and connect the ANT OUT jack of the VCR to the ANT IN jack of the TV using 75 Ω shielded cable.
12 Inst allation Digit al CA TV T erminal connection to component with Digit al Audio Input jack Follow this diagram to connect the Digital CA TV T erminal to a component with a Digit al Audio Input jack.
13 Power ON/OFF Installation Push the POWER button on this unit to turn the set on POWER-ON Press POWER once more to turn off. Power Indicator: Green Power Indicator: Indicator not illuminated ( Please underst and the Digital CA TV T erminal is not updated when you plug off from AC outlet.
14 Remote Control CBL, TV , VCR, AUX Press to select remote operation. POWER Press to turn ON and OFF . Press to move through interactive screen choices. SELECT Press to choose interactive screen item. Page Press to display Next/Previous screen. A, B, C On-Screen decision buttons CH Press to select channel Up/Down Mute Press to turn sound off.
15 Remote Control Remote Control Function Key Chart ALL COMPONENTS ALL COMPONENTS CBL CBL TV VCR CBL TV VCR AUX CBL, TV CBL CBL, TV CBL CBL CBL CBL, TV , VCR CBL, TV , VCR AUX CBL, TV , VCR CBL, TV T .
16 Remote Control Remote Control Function Key Chart CBL, TV , VCR Select channel Select code The description of functions for each of the components in the table above apply when the factory default code settings are in place.
17 Programming the Remote Control The Universal Remote Control can be programmed to operate many manufacturers’components using the component function buttons for T V , VCR, or AUX. Follow the procedures for programming your Remote Control with and without codes for the component.
18 Programming the Remote Control n Programming Without Code If you cannot find the right Code, you can call up all Codes one after the other to search for a Code.
19 Programming the Remote Control n Programming for volume control The volume adjustment function can be locked so that regardless of whether CBL, T V or VCR mode is active, the volume is adjusted for only one of the modes. (Refer to the table below .
20 n Changing button functions The functions of the remote control buttons can be assigned to other buttons. Setting method (Example) Assigning the function of the POWER button in TV mode to the Exit button in VCR mode 1. Press the Setup button and hold for 3 seconds (until the visible LED blinks twice).
21 Programming the Remote Control Component Codes The Universal Remote Control is capable of operating many component brands after entering a code. Some components may not operate. The Universal Remote Control does not control all features in all models.
22 Programming the Remote Control Codes for TVs (for TV mode) (continued) Manufacturer List Manufacturer Set Up No. Manufacturer Set Up No. Soundesign 0180, 0178, 0179 Squareview 0171 S tarlite 0180 S.
23 Programming the Remote Control Codes for VCRs (for VCR mode) (continued) Manufacturer List Manufacturer Set Up No. Manufacturer Set Up No. Sanky 0048, 0039 Sansui 0000, 0067, 0209, 0041 Sanyo 0047,.
24 Programming the Remote Control Codes for Audio Amp/T uners (for AUX mode) Manufacturer List Manufacturer Set Up No. Manufacturer Set Up No. ADC 0531 Aiwa 1089, 1405, 0158, 0189, 0121, 0405 Capetron.
25 T roubleshooting Symptom Remedy No power No reception No picture No sound Distorted picture No color The remote control is not responding Check that the AC power plug is securely plugged into the power outlet. l Check that equipment is connected properly .
26 S pecifications Power Source Power Consumption Operating conditions Connection terminals Dimensions (WxHxD) Weight (Mass) 120 V AC, 60 Hz T emperature : 32 °F-104 °F(0 °C - 40 °C) Humidity: 20 .
27 Notes.
28 Customer Record The model number and serial number of this product can be found on its rear panel. Y ou should note this serial number in the space provided below and retain this book, plus your purchase receipt, as a permanent record of your purchase to aid in identification in the event of thef t or loss, and for W arranty Service purposes.
デバイスPanasonic TZ-PCD2000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Panasonic TZ-PCD2000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPanasonic TZ-PCD2000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Panasonic TZ-PCD2000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Panasonic TZ-PCD2000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Panasonic TZ-PCD2000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPanasonic TZ-PCD2000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Panasonic TZ-PCD2000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPanasonic TZ-PCD2000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。