Planet TechnologyメーカーVRT-401の使用説明書/サービス説明書
ページ先へ移動 of 125
Networking & Communicat io n Broadband VPN Router VRT-401 User ’ s Manual.
ii Cop y right Copyright (C) 2002 PLANET Technology Corp. All rights reserved. The products and programs described in this User ’ s M anual are licensed products of PLANET Technology, This User ’ .
i Table of Contents CH A P T ER 1 IN T RODUC T IO N ..................................................................................... .1 VR T -401 Feature s ..........................................................................................
ii Example s ............................................................................................................. . 83 Using Certificate s ............................................................................................. . 101 CH A P T ER 9 O T HER FE A T URES A ND SE TT ING S .
1 Chapter 1 Introduction This Chapter provides an overview of VRT-401's features and capabili- ties. Congratulations on the purchase o f y our ne w VR T -401. VR T -401 is a m ulti- f unction device providing the f ollo w ing services: • Shared Broadband Internet Access f or all LAN users.
VRT-401 User Manual 2 A d v anced Internet Functions • Communication Applications. Support f or Internet co mm unication applica- tions, such as interactive Ga m es, T elephon y , and Con f erencing applications, w hich are o f ten di ff icult to use w hen behind a Fire w all, is included.
Introduction 3 tion and even the existence o f each PC is hidden. Fro m the external vie w point, there is no net w or k , onl y a single device - VR T -401.
VRT-401 User Manual 4 Ph y sical Details Front-mounted LEDs Figure 2: Front Panel Po w er On - Po w er on. Off - No po w er. Status (Red) On - Error condition. Off - Nor m al operation. Blinking - T his LED blin k s during start up. L A N For each port, there are 2 LEDs • LNK/ A C T • On - Corresponding LAN port is active.
Introduction 5 Rear Panel Figure 3: Rear Panel D M Z Use a standard LAN cable to connect a nor m al port on the other hub. Reset Button T his button has t w o (2) f unctions: • Reboot . W hen pressed and released, VR T -401 w ill reboot (restart). • Clear A ll Data .
6 Chapter 2 Installation This Chapter covers the physical installation of VRT-401. Requirements • Net w or k cables. Use standard 10/100Base T net w or k (U T P) cables w ith RJ45 connectors.
Installation 7 • I f desired, connect the DMZ port to a standard port on a Hub. PCs connected to this hub w ill also gain Internet access, but w ill NO T be able to access the rest o f the LAN. 3. Connect W A N Cable Connect the DSL or Cable m ode m to the W AN port on VR T -401.
8 Chapter 3 Setup This Chapter provides Setup details of VRT-401. O v er v ie w T his chapter describes the setup procedure f or: • Internet Access • LAN con f iguration PCs on y our local LAN m a y also require con f iguration. For details, see Chapter 4 - PC Configuration .
Setup 9 Con f igure or use an y o f the f ollo w ing: • PC Database • Re m ote Ad m in • Routing (RIP and static Routing) • Upgrade f ir m w are • Enable/Disable UPnP Support Chapter 9: Othe.
VRT-401 User Manual 10 2. Start y our W EB bro w ser. 3. In the Address box, enter "H TT P://" and the IP Address o f VR T -401, as in this exa m ple, w hich uses VR T -401 ’ s de f ault IP Address: H TT P://192.
Setup 11 Config Wizard T he f irst ti m e y ou connect to VR T -401, the Con f ig W i z ard w ill run auto m aticall y . ( T he Setup W i z ard w ill also run i f VR T -401 ’ s de f ault settings are restored.) 1. Step through the W i z ard until f inished.
VRT-401 User Manual 12 PP T P Mainl y used in Europe. Y ou connect to the ISP onl y w hen required. T he IP address is usuall y allocated auto m aticall y , but m a y be Static (Fixed). • PP T P Server IP Address. • User na m e and pass- w ord. • IP Address allocated to y ou, i f Static (Fixed).
Setup 13 Home Screen A f ter f inishing or exiting the Setup W i z ard, y ou w ill see the Home screen. W hen y ou connect in f uture, y ou w ill see this screen w hen y ou connect.
VRT-401 User Manual 14 L A N Screen Use the LAN lin k on the m ain m enu to reach the LAN screen An exa m ple screen is sho w n belo w . Figure 7: L A N Screen Data - L A N Screen T CP/IP IP A ddress IP address f or VR T -401, as seen f ro m the local LAN.
Setup 15 DHCP What DHCP Does A DHCP (D y na m ic Host Con f iguration Protocol) Ser v er allocates a valid IP address to a DHCP Client (PC or device) upon request.
16 Chapter 4 PC Configuration This Chapter details the PC Configuration required on the local ("Inter- nal") LAN. O v er v ie w For each PC, the f ollo w ing m a y need to be con f igured: .
PC Configuration 17 Checking TCP/IP Settings - Windo w s 9x/ME: 1. Select Control Panel - Network . Y ou should see a screen li k e the f ollo w ing: Figure 8: Net w ork Configuration 2. Select the TCP/IP protocol f or y our net w or k card. 3. Clic k on the Properties button.
VRT-401 User Manual 18 • On the Gateway tab, enter VR T -401 ’ s IP address in the New Gateway f ield and clic k Add , as sho w n belo w . Y our LAN ad m inistrator can advise y ou o f the IP Ad- dress the y assigned to VR T -401. Figure 10: Gate w a y T ab (Win 95/98) • On the DNS Configuration tab, ensure Enable DNS is selected.
PC Configuration 19 Checking TCP/IP Settings - Windo w s NT4.0 1. Select Control Panel - Network , and, on the Protocols tab, select the T CP/IP protocol, as sho w n belo w . Figure 12: Windo w s N T 4.0 - T CP/IP 2. Clic k the Properties button to see a screen li k e the one belo w .
VRT-401 User Manual 20 Figure 13: Windo w s N T 4.0 - IP A ddress 3. Select the net w or k card f or y our LAN. 4. Select the appropriate radio button - Obtain an IP address from a DHCP Server or Specify an IP Address , as explained belo w . Obtain an IP address from a DHCP Ser v er T his is the de f ault W indo w s setting.
PC Configuration 21 Figure 14 - Windo w s N T 4.0 - A dd Gate w a y 2. T he DNS should be set to the address provided b y y our ISP, as f ollo w s: • Clic k the DNS tab. • On the DNS screen, sho w n belo w , clic k the Add button (under DNS Service Search Order ), and enter the DNS provided b y y our ISP.
VRT-401 User Manual 22 Figure 15: Windo w s N T 4.0 - DNS.
PC Configuration 23 Checking TCP/IP Settings - Windo w s 2000: 1. Select Control Panel - Network and Dial-up Connection . 2. Right - clic k the Local Area Connection icon and select Properties . Y ou should see a screen li k e the f ollo w ing: Figure 16: Net w ork Configuration (Win 2000) 3.
VRT-401 User Manual 24 Figure 17: T CP/IP Properties (Win 2000) 5. Ensure y our T CP/IP settings are correct, as described belo w . Using DHCP T o use DHCP, select the radio button Obtain an IP Address automatically . T his is the de f ault W indo w s setting.
PC Configuration 25 Checking TCP/IP Settings - Windo w s XP 1. Select Control Panel - Network Connection . 2. Right clic k the Local Area Connection and choose Properties . Y ou should see a screen li k e the f ollo w ing: Figure 18: Net w ork Configuration (Windo w s XP) 3.
VRT-401 User Manual 26 Figure 19: T CP/IP Properties (Windo w s XP) 5. Ensure y our T CP/IP settings are correct. Using DHCP T o use DHCP, select the radio button Obtain an IP Address automatically . T his is the de f ault W indo w s setting. Using this is recommended .
PC Configuration 27 Internet A ccess T o con f igure y our PCs to use VR T -401 f or Internet access: • Ensure that the DSL m ode m , Cable m ode m , or other per m anent connection is f unctional. • Use the f ollo w ing procedure to con f igure y our Bro w ser to access the Internet via the LAN, rather than b y a Dial-up connection.
VRT-401 User Manual 28 M acintosh Clients Fro m y our Macintosh, y ou can access the Internet via VR T -401. T he procedure is as f ollo w s. 1. Open the T CP/IP Control Panel. 2. Select Ethernet f ro m the Connect via pop-up m enu. 3. Select Using DHCP Server f ro m the Configure pop-up m enu.
29 Chapter 5 Operation and Status This Chapter details the operation of VRT-401 and the status screens. Operation Once both VR T -401 and the PCs are configured, operation is automatic.
VRT-401 User Manual 30 Data - Status Screen Internet Connection M ethod T his indicates the current connection m ethod, as set in the Setup W i z ard. Broadband M odem T his sho w s the connection status o f the m ode m .
Operation and Status 31 Connection Status - PPPoE I f using PPPoE (PPP over Ethernet), a screen li k e the f ollo w ing exa m ple w ill be dis- pla y ed w hen the "Connection Details" button is clic k ed.
VRT-401 User Manual 32 Connection Log Connection Log • T he Connection Log sho w s status m essages relating to the existing connection. • T he m ost co mm on m essages are listed in the table belo w . • T he "Clear Log" button w ill restart the Log, w hile the Re f resh button w ill update the m essages sho w n on screen.
Operation and Status 33 Error: Invalid or un- k no w n pac k et t y pe T he data received f ro m the ISP's Server could not be processed. T his could be caused b y data corruption ( f ro m a bad lin k ), or the Server using a protocol w hich is not supported b y this device.
VRT-401 User Manual 34 Connection Status - PPTP I f using PP T P (Peer-to-Peer T unneling Protocol), a screen li k e the f ollo w ing exa m ple w ill be displa y ed w hen the "Connection Details" button is clic k ed.
Operation and Status 35 Buttons Connect I f not connected, establish a connection to y our ISP. Disconnect I f connected to y our ISP, hang up the connection. Clear Log Delete all data currentl y in the Log. T his w ill m a k e it easier to read ne w m essages.
VRT-401 User Manual 36 Connection Status T his indicates w hether or not the connection is currentl y established. • I f the connection does not exist, the "Connect" button can be used to establish a connection. • I f the connection currentl y exists, the "Disconnect" button can be used to brea k the connection.
Operation and Status 37 Data - Sing T el R A S Screen Internet R A S Plan T he RAS Plan w hich is currentl y used. Ph y sical A d- dress T he hard w are address o f this device, as seen b y re m ote de- vices on the Internet. ( T his is di ff erent to the hard w are address seen b y devices on the local LAN.
VRT-401 User Manual 38 Connection Details - Fixed/D y namic IP A ddress I f y our access m ethod is "Direct" (no login), a screen li k e the f ollo w ing exa m ple w ill be displa y ed w hen the "Connection Details" button is clic k ed.
Operation and Status 39 Buttons Release/Rene w Button w ill displa y EI T HER "Release" OR "Rene w " T his button is onl y use f ul i f the IP address sho w n above is allocated auto m aticall y on connection. (D y na m ic IP address).
40 Chapter 6 Internet Features This Chapter explains when and how to use VRT-401 ’ s "Internet" Fea- tures. O v er v ie w T he f ollo w ing advanced f eatures are provided.
Internet Features 41 Communication A pplications Most applications are supported transparentl y b y VR T -401. But so m eti m es it is not clear w hich PC should receive an inco m ing connection. T his proble m could arise w ith the Communication Applications listed on this screen.
VRT-401 User Manual 42 Figure 27: Special A pplications Screen Data - Special A pplications Screen Checkbox Use this to Enable or Disable this Special Application as required.
Internet Features 43 If an application still cannot function correctl y , tr y using the "D M Z" feature. DMZ T his f eature, i f enabled, allo w s one (1) co m puter on y our LAN to be expo.
VRT-401 User Manual 44 URL Filter Screen Clic k the "Con f igure URL Filter" button on the Advanced Internet screen to access the URL Filter screen. An exa m ple screen is sho w n belo w . Figure 28: URL Filter Screen Data - URL Filter Screen Filter Strings Current Entries T his lists an y existing entries.
Internet Features 45 D y namic DNS (Domain Name Ser v er) T his f ree service is ver y use f ul w hen co m bined w ith the Virtual Server f eature. It allo w s Internet users to connect to y our Virtual Servers using a URL, rather than an IP Ad- dress.
VRT-401 User Manual 46 Data - D y namic DNS Screen DDNS Ser v ice DDNS Ser v ice • Y ou m ust sign up f irst to create a ne w account be f ore using the service. T he service is f ree. • Clic k this lin k to connect to the www .d y ndns.org W eb site.
Internet Features 47 Virtual Ser v ers T his f eature allo w s y ou to m a k e Servers on y our LAN accessible to Internet users. Nor m all y , Internet users w ould not be able to access a server on y our LAN because: • Y our Server does not have a valid external IP Address.
VRT-401 User Manual 48 Using the DMZ port for Virtual Ser v ers Y ou should connect y our Virtual Servers to the DMZ port, f or the f ollo w ing reasons: • T ra ff ic passing bet w een the DMZ and LAN passes through the f ire w all.
Internet Features 49 Defining y our o w n Virtual Ser v ers I f the t y pe o f Server y ou w ish to use is not listed on the Virtual Servers screen, y ou can use the Fire w all Rules to allo w particular inco m ing tra ff ic and f or w ard it to a speci f ied PC (Server).
VRT-401 User Manual 50 MT U MT U size M T U (Maxi m u m T rans m ission Unit) value should onl y be changed i f advised to do so b y T echnical Support. • Enter a value bet w een 1 and 1500. • T his device w ill still auto-negotiate w ith the re m ote server, to set the M T U si z e.
51 Chapter 7 Securit y Configuration This Chapter explains the settings available via the security configura- tion section of the "Security" menu.
VRT-401 User Manual 52 Figure 34: Pass w ord Dialog Enter the "User Na m e" and "Pass w ord" y ou set on the Admin Login screen above.
Security Configuration 53 A ccess Control T his f eature is accessed b y the Access Control lin k on the Securit y m enu. T he Access Control f eature allo w s ad m inistrators to restrict the level o f Internet Ac- cess available to PCs on y our LAN.
VRT-401 User Manual 54 Data - A ccess Control Screen Group Group Select the desired Group. T he screen w ill update to displa y the settings f or the selected Group. Groups are na m ed "De- f ault", "Group 1", "Group 2", "Group 3" and "Group 4", and cannot be re-na m ed.
Security Configuration 55 Vie w Log Clic k this to open a sub- w indo w w here y ou can vie w the "Access Control" log. T his log sho w s atte m pted Internet accesses w hich have been bloc k ed b y the Access Control f eature.
VRT-401 User Manual 56 Group Members Screen T his screen is displa y ed w hen the M embers button on the Access Control screen is clic k ed. Figure 36: Group M embers Use this screen to add or re m ove m e m bers (PCs) f ro m the current group.
Security Configuration 57.
VRT-401 User Manual 58 Fire w all Rules For nor m al operation and LAN protection, it is not necessar y to use this screen. T he Fire w all w ill al w a y s bloc k DoS (Denial o f Service) attac k s.
Security Configuration 59 Data - Fire w all Rules Screen Rule List Vie w Rules for .. Select the desired option; the screen w ill update and list an y current rules. I f y ou have not de f ined an y rules, the list w ill be e m pt y . Data For each rule, the f ollo w ing data is sho w n: • Name - T he na m e y ou assigned to the rule.
VRT-401 User Manual 60 Define Fire w all Rule Clic k ing the "Add" button in the Firewall Rules screen w ill displa y a screen li k e the exa m ple belo w . Figure 38: Define Fire w all Rule Data - Define Fire w all Rule Screen Name Enter a suitable na m e f or this rule.
Security Configuration 61 Dest IP T hese settings deter m ine w hich tra ff ic, based on their destination IP address, is covered b y this rule. Select the desired option: • An y - All tra ff ic f ro m the source port is covered b y this rule. • Single address - Enter the required IP address in the "Start IP address" f ield".
VRT-401 User Manual 62 Logs T he Logs record various t y pes o f activit y on VR T -401. T his data is use f ul f or trouble- shooting, but enabling all logs w ill generate a large a m ount o f data and adversel y a ff ect per f or m ance.
Security Configuration 63 A ccess Control I f enabled, the log w ill include atte m pted outgoing connec- tions w hich have been bloc k ed b y the "Access Control" f eature. Fire w all Rules I f enabled, the log w ill details o f pac k ets bloc k ed b y user- de f ined Fire w all rules.
VRT-401 User Manual 64 Include Select the logs y ou w ish to be included..
Security Configuration 65 Securit y Options T his screen allo w s y ou to set Fire w all and other securit y -related options. Figure 40: Securit y Options Screen Data - Securit y Options Screen SPI Fire w all Enable DoS Fire w all I f enabled, DoS (Denial o f Service) attac k s w ill be detected and bloc k ed.
VRT-401 User Manual 66 Options Respond to IC M P T he ICMP protocol is used b y the "ping" and "trace route" pro- gra m s, and b y net w or k m onitoring and diagnostic progra m s. • I f chec k ed, VR T -401 w ill respond to ICMP pac k ets received f ro m the Internet.
Security Configuration 67 Scheduling • T his schedule can be (optionall y ) applied to an y Access Control Group. • Bloc k ing w ill be per f or m ed during the scheduled ti m e (bet w een the "Start" and "Finish" ti m es.) • T w o (2) separate sessions or periods can be de f ined.
VRT-401 User Manual 68 Ser v ices Services are used in de f ining tra ff ic to be bloc k ed or allo w ed b y the Access Control or Firewall Rules f eatures. Man y co mm on Services are pre-de f ined, but y ou can also de f ine y our o w n services i f required.
Security Configuration 69 service. Buttons Delete Delete the selected service f ro m the list. A dd Add a ne w entr y to the Service list, using the data sho w n in the "Add Ne w Service" area on screen. Cancel Clear the " Add Ne w Service " area, read y f or entering data f or a ne w Service.
70 Chapter 8 VPN This Chapter describes the VPN capabilities and configuration required for common situations. O v er v ie w T his section describes the VPN (Virtual Private Net w or k ) support provided b y y our VR T -401.
VPN 71 • Phase I is the negotiation and establish m ent up o f the IKE connection. • Phase II is the negotiation and establish m ent up o f the IPsec connection. Because the IKE and IPsec connections are separate, the y have di ff erent SAs (secu- rit y associations).
VRT-401 User Manual 72 Common VPN Situations VPN Pass-through Figure 43: VPN Pass-through Here, a PC on the LAN behind the Router/Gate w a y is using VPN so f t w are, but the Router/Gate w a y is NO T acting as a VPN endpoint. It is onl y allo w ing the VPN connec- tion.
VPN 73 Connecting 2 L A Ns v ia VPN Figure 45: Connecting 2 VPN Gate w a y s T his allo w s t w o (2) LANs to be connected. PCs on each endpoint gain secure access to the re m ote LAN.
VRT-401 User Manual 74 VPN Configuration T his section covers the con f iguration required on VR T -401 w hen using Manual Ke y Exchange (Manual Policies) or IKE (Auto m atic Policies). Details o f using Certi f icates are covered in a later section. VPN Policies Screen T o vie w this screen, select VPN Policies f ro m the VPN m enu.
VPN 75 Operations A dd T o add a ne w polic y , clic k the "Add" button. See the f ollo w ing section f or details. Edit T o Edit or m odi f y an existing polic y , select it and clic k the "Edit" button.
VRT-401 User Manual 76 • Other w ise, clic k Next to continue. Y ou w ill see a screen li k e the f ollo w ing. Figure 48: VPN Wizard - General General Settings Polic y Name Enter a suitable na m e. T his na m e is not supplied to the re m ote VPN. It is used onl y to help y ou m anage the policies.
VPN 77 Figure 49: VPN Wizard - T raffic Selector • For outgoing VPN connections, these settings deter m ine w hich tra ff ic w ill cause a VPN tunnel to be created, and w hich tra ff ic w ill be sent through the tunnel.
VRT-401 User Manual 78 Remote IP addresses T y pe • Single address - enter an IP address in the "Start IP address" f ield. • Range address - enter the starting IP address in the "Start IP address" f ield, and the f inish IP address in the "Finish IP address" f ield.
VPN 79 T hese settings m ust m atch the re m ote VPN. Note that y ou cannot use both AH and ESP. M anuall y assigned Ke y s A H A uthentication AH (Authentication Header) speci f ies the authentication protocol f or the VPN header, i f used. (AH is o f ten NO T used) I f AH is not enabled, the f ollo w ing settings can be ignored.
VRT-401 User Manual 80 For Manual Ke y Exchange, con f iguration is no w co m plete. • Clic k "Next" to vie w the f inal screen. • On the f inal screen, clic k "Finish" to save y our settings, then "Close" to exit the W i z ard.
VPN 81 A uthentication • RS A Signature requires that both VPN endpoints have valid Certi f icates issued b y a CA (Certi f ication Authorit y ). • For Pre-shared key , enter the sa m e k e y value in both endpoints. T he k e y should be at least 8 characters ( m axi- m u m is 128 characters).
VRT-401 User Manual 82 IKE Phase 2 (IPsec S A ) IPsec S A Life T ime T his setting does not have to m atch the re m ote VPN end- point; the shorter ti m e w ill be used. Although m easured in seconds, it is co mm on to use ti m e periods o f several hours, such 28,800 seconds.
VPN 83 Examples T his section describes so m e exa m ples o f using VR T -401 in co mm on VPN situations. Example 1: Connecting 2 VRT-401s In this exa m ple, 2 LANs are connected via VPN. Figure 53: Connecting 2 VR T -401s Note • T he LANs MUS T use di ff erent IP address ranges.
VRT-401 User Manual 84 Pre-shared Ke y Xxxxxxxxxx Xxxxxxxxxx Must m atch IKE Authentica- tion algorith m MD5 MD5 Must m atch IKE Encr y ption DES DES Must m atch IKE Exchange m ode Main Mode Main Mode Must m atch DH Group Group 1 (768 bit) Group 1 (768 bit) Must m atch IKE SA Li f e ti m e 28800 28800 Does not have to m atch.
VPN 85 Example 2: Windo w s 2000/XP Client to L A N In this exa m ple, a W indo w s 2000/XP client connects to VR T -401 and gains access to the local LAN. Figure 54: Windo w s 2000/XP Client to VR T -401 T o use 3DES encr y ption, y ou need Ser v ice Pack 3 or later installed on Windo w s 2000.
VRT-401 User Manual 86 m ode DH Group Group 1 (768 bit) Must m atch client PC IKE SA Li f e ti m e 28800 Does not have to m atch client PC. Shorter period w ill be used. IKE PFS Disable Must m atch client PC IPSec S A Parameters IPSec SA Li f e ti m e 28800 Do not have to m atch.
VPN 87 Figure 56: Windo w s 2000/XP - Polic y Properties • Note that no rules are in use. T w o 2 rules are required - inco m ing and outgo- ing. • T he outgoing rule w ill be added f irst. 6. Deselect the "Use Add W i z ard" chec k box, then clic k "Add" to vie w the screen belo w .
VRT-401 User Manual 88 Figure 58: Filter Properties: A ddressing 8. Enter the Source IP address and the Destination IP address . • Since this is the outing f ilter, the Source IP address is "M y IP address" and the Destination IP address is the address range used on the re m ote LAN.
VPN 89 Figure 60: Ne w Rule Properties: Filter A ction 11. Select Require Security , then clic k the "Edit" button, to vie w the Require Security Properties screen. Figure 61: Require Securit y Properties 12. Select Negotiate security (this selects IKE), then clic k "Add".
VRT-401 User Manual 90 Figure 62: M odif y Securit y M ethod 13. On the resulting screen (above), select High [ESP] then clic k "OK" to save y our changes and return to the Require Security Properties screen. Figure 63: Require Securit y Properties 14.
VPN 91 15. Clic k the Tunnel Setting tab, then select The tunnel endpoint is specified by this IP address . Enter the W AN (Internet) IP address o f VR T -401, as sho w n belo w . Figure 64: T unnel Setting 16. Clic k the Authentication M ethods tab, then clic k the "Edit" to see the screen li k e the exa m ple belo w .
VRT-401 User Manual 92 19. Clic k "Close" to return to the DUT to W in2K properties screen. T he " T o DU T " f ilter should no w be listed, as sho w n belo w . Figure 66: Windo w s 2000/XP Client to VR T -401 20. T o add the second (outgoing) rule, clic k "Add".
VPN 93 Figure 68: Filter Properties: A ddressing 22. Clic k "OK" to save y our changes, then "Close". Figure 69: Filter List 23. Ensure the " T o W in2K" f ilter is selected, then clic k the Filter Action tab.
VRT-401 User Manual 94 Figure 70: Filter A ction 24. Select Require Security , then clic k "Edit". On the Require Security M ethods screen belo w , select Negotiate security . Figure 71: Securit y M ethods 25. Clic k the "Add" button.
VPN 95 Figure 72: M odif y Securit y M ethod 26. Clic k "OK" to save y our changes, then clic k "OK" again to return to the Filter Action screen. 27. Select the Tunnel Setting tab, and enter the W AN (Internet) IP address o f this PC (172.
VRT-401 User Manual 96 Figure 74: A uthentication M ethod 29. Select Use this string to protect the key exchange (preshared key) , then enter y our preshared k e y in the f ield provided. 30. Clic k "OK" to save y our settings, then "Close" to return to the DUT to W in2K Prop- erties screen.
VPN 97 Figure 76: Properties - General T ab 32. Clic k the "Advanced" button to see the screen belo w . Figure 77: Ke y Exchange Settings 33.
VRT-401 User Manual 98 Figure 78: Ke y Exchange Securit y M ethods 34. Select the f irst entr y , and clic k the "Edit" button to see the f ollo w ing screen.
VPN 99 Example 3: Windo w s 2000 Ser v er to VPN Gate w a y In this exa m ple, a W indo w s 2000 Server connects to VR T -401. Users on each LAN can then gain access to the re m ote LAN.
VRT-401 User Manual 100 Windo w s 2000 Ser v er Configuration Con f iguration is the sa m e as f or Example 2: W indows 2000/XP Client to except f or speci f y ing the Source and Destination addresses f or the "Filter Properties". Instead, f or both IP Filters, the Filter Properties- Addressing should be co m pleted as f ollo w s.
VPN 101 Using Certificates Certi f icates are used to authenticate users. Certi f icates are issued to y ou b y various CAs (Certi f ication Authorities). T hese Certi f icates are called "Sel f Certi f icates". Each CA also issues a certi f icate to itsel f .
VRT-401 User Manual 102 A dding a Trusted Certificate 1. A f ter obtaining a ne w Certi f icate f ro m the CA, y ou need to upload it to VR T -401. 2. On the "Certi f icates" screen, clic k the "Add T rusted Certi f icate" button to vie w the Add Trusted Certificate screen, sho w n belo w .
VPN 103 Subject Name T his is the na m e w hich other organi z ations w ill see as the Holder (o w ner) o f this Certi f icate. T his should be y our registered business na m e or o ff icial co m pan y na m e. Generall y , all Certi f icates should have the sa m e value in the Subject f ield.
VRT-401 User Manual 104 Figure 87: A dd Self Certificate (3) 8. Upload the Certi f icate: • Clic k the "Bro w se" button, and locate the certi f icate f ile on y our PC • Select the f ile. T he na m e w ill appear in the "Certi f icate File" f ield.
VPN 105 Figure 89: Upload CRL 4. Upload the CRL f ile: • Clic k the "Bro w se" button, and locate the CRL f ile on y our PC • Select the f ile. T he na m e w ill appear in the "File to Upload" f ield. • Clic k "Upload" to upload the CRL f ile to VR T -401.
106 Chapter 9 Other Features and Settings This Chapter explains the screens and settings available via the " M iscellaneous" menu. O v er v ie w Nor m all y , it is not necessar y to use these screens, or change an y settings.
Other Features and Settings 107 PC Database T he PC Database is used w henever y ou need to select a PC (e.g. f or the "DMZ" PC). It eli m inates the need to enter IP addresses. Also, y ou do not need to use f ixed IP addresses on y our LAN.
VRT-401 User Manual 108 Data - PC Database Screen Kno w n PCs T his lists all current entries. Data displa y ed is name (IP Address) type . T he "t y pe" indicates w hether the PC is connected to the LAN. Name I f adding a ne w PC to the list, enter its na m e here.
Other Features and Settings 109 PC Database ( A dmin) T his screen is displa y ed i f the "Advanced Ad m inistration" button on the PC Database is clic k ed. It provides m ore control than the standard PC Database screen. Figure 91: PC Database ( A dmin) Data - PC Database ( A dmin) Screen Kno w n PCs T his lists all current entries.
VRT-401 User Manual 110 IP A ddress Select the appropriate option: • A utomatic - T he PC is set to be a DHCP client ( W indo w s: "Obtain an IP address auto m aticall y "). VR T -401 w ill allocate an IP address to this PC w hen requested to do so.
Other Features and Settings 111 Remote A dministration T his f eature allo w s y ou to m anage VR T -401 via the Internet. Figure 92: Remote A dministration Screen Data - Remote A dministration Screen Remote A dministration Enable Remote A dministration Enable to allo w ad m inistration via the Internet.
VRT-401 User Manual 112 Routing O v er v ie w • I f y ou don't have other Routers or Gate w a y s on y our LAN, y ou can ignore the "Routing" page co m pletel y . • I f VR T -401 is onl y acting as a Gate w a y f or the local LAN seg m ent, ignore the "Routing" page even i f y our LAN has other Routers.
Other Features and Settings 113 Figure 93: Routing Screen Data - Routing Screen RIP Enable RIP Chec k this to enable the RIP (Routing In f or m ation Protocol) f eature o f VR T -401. VR T -401 supports RIP 1 onl y . Static Routing Static Routing T able Entries T his list sho w s all entries in the Routing T able.
VRT-401 User Manual 114 Properties • Destination Net w ork - T he net w or k address o f the re m ote LAN seg m ent. For standard class "C" LANs, the net w or k address is the f irst 3 f ields o f the Destination IP Address. T he 4th (last) f ield can be le f t at 0.
Other Features and Settings 115 Other Routers on the Local L A N Other routers on the local LAN m ust use VR T -401 ’ s Local Router as the Default Route . T he entries w ill be the sa m e as VR T -401 ’ s local router, w ith the exception o f the Gateway IP Address .
VRT-401 User Manual 116 For Router B's Default Route Destination IP Address 0.0.0.0 Net w or k Mas k 0.0.0.0 Gate w a y IP Address 192.168.1.80 (VR T -401 ’ s local router) Firm w are Upgrade T he f ir m w are (so f t w are) in VR T -401 can be upgraded using y our W eb Bro w ser.
Other Features and Settings 117 UPNP An exa m ple UPNP screen is sho w n belo w . Figure 96: UPNP Screen Data - UPNP Screen UPnP Enable UPnP Ser v ices • UPnP (Universal Plug and Pla y ) allo w s auto m atic discover y and con f iguration o f equip m ent attached to y our LAN.
118 A ppendix A T roubleshooting This Appendix covers the most likely problems and their solutions. O v er v ie w T his chapter covers so m e co mm on proble m s that m a y be encountered w hile using VR T -401 and so m e possible solutions to the m .
Appendi x A - Troubleshooting 119 Solution 2: VR T -401 processes the data passing through it, so it is not transpar- ent. Use the Special Applications f eature to allo w the use o f Internet applications w hich do not f unction correctl y . I f this does solve the proble m y ou can use the D MZ f unction.
120 Appendix B Specifications VRT-401 Model VR T -401 Di m ensions 170 mm ( W ) * 147 mm (D) * 27 mm (H) Operating T e m pera- ture 0 ° C to 40 ° C Storage T e m perature -10 ° C to 70 ° C Net w o.
Appendi x B - Specifications 121 FCC Radiation Exposure Statement T his equip m ent co m plies w ith FCC RF radiation exposure li m its set f orth f or an uncon- trolled environ m ent. T his equip m ent should be installed and operated w ith a m ini m u m distance o f 20 centi m eters bet w een the radiator and y our bod y .
デバイスPlanet Technology VRT-401の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Planet Technology VRT-401をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPlanet Technology VRT-401の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Planet Technology VRT-401の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Planet Technology VRT-401で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Planet Technology VRT-401を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPlanet Technology VRT-401の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Planet Technology VRT-401に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPlanet Technology VRT-401デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
