AudiメーカーAUD-Sの使用説明書/サービス説明書
ページ先へ移動 of 24
INST ALLA TION AND OWNER’S MANUAL As of date of man ufacture, meets all ANSI/UL 325 Safety Requ irements fo r Vehic ular do or oper ators AUD-S AU SERIES WITH SOLID ST A TE CONTROL CIRCUITR Y DRA WB.
READ THESE STATEMENTS CA R EFULLY AND FOLLOW THE INSTRUCTIONS CLOSELY. The Warning and Caution boxes througho ut th is manual are th ere to protect you and your equipment. Pay close at tention to these boxes as you follow the manual. WARNING Indicates a MECHANICAL haz ard of INJURY OR DEATH.
M O D EL AU D- S OP ER AT O R A P P LI C AT I O N S : Drawbar op erators are for commercial and in dustrial use on secti onal over head do ors whic h use horiz ontal track wi th norm al radi us. A dra w bar opera tor i s not suitab le for do ors with high lift exceed ing 24 inc hes or vert ical lift doors.
Before starting the installation of the operator, the door m ust be in good working condition and properly counterbalanced. Inspect the door and track for loose or m issing hard ware. Test the door manually for balance and ease of op eration. Lubricate door hinges and rollers.
T O REDUCE THE RISK OF SEVERE INJUR Y O R D E A T H : R E AD AN D F O L L O W AL L INST ALLA TION INSTRUCTIONS! WARNING ITEM # PART# DESCRIPTION QUAN. 1 Operat or Po wer Head 1 2 Tra ck Rails 2 7 00 6.
2) After the track is assembled, position track assemb l y onto the operator power head and attach w ith four 3/8”-16 x 1” bolts, lock washers and nuts (supplied in a separate hardw are package #100470). NOTE: To k eep #41 chain (used on 1/2 and 3/4 H.
TO A VOID D A M AGE TO DOOR A ND OPERATOR ENSURE A LL DOOR LOCKS A RE DIS ABLED. USE A N IN TERLOCK SW ITCH IF A LOCK IS REQU IRED TO RE T A IN FUNCTIONA LITY. CA UTION 1) Locate the center of the doo r and mark a line on the wall directly abo ve the door.
4) Mount the front mounting bracket ( Item 9) to the mounting pad as shown in Fig ure 8. The location of the door’s torsion shaft may prevent you from placing the mountin g pad in the location shown. Mount the pad as close as possible to t hree (3) inches above the door’s high arc point.
8) Figure 12 details a ty pical method of hanging the operator from the ceiling. Each installation will vary due to the difference in building structure s; but in all installations side braces should be used to further strengthen the installation. I f the operator track (rail) is lo ng er than 15 feet a m id support is recommended.
TO A VOID DAMAGE TO DOOR A ND OPERA T OR ENSURE A LL DOOR LOCKS A RE DIS ABLED. USE A N INTERL OCK SWITCH IF A LOCK IS REQU IRED TO RE T A IN FUNCTIONA LITY. CA UTION TO PR EVENT THE RISK OF PERSONA L INJU RY AND /OR D A M AGE TO DOOR OR PROPERTY, ONL Y OPERA TE DOOR CONTROL WHEN DOOR IS IN CLEA R V IEW.
Figure 15 OPEN TB1 STOP CLOSE OPEN COM CLOSE STOP NO REV NC REV PHOTO COM SINGLE ILOCK 24 VAC COM SAFE FINISH PHOTOBEAM 3-WIRE PH OTOBEAM MOTOR CONT ROL BOARD Door Edge and P hotoelectric Wiring See text on pa ge 10 for ope ration when S afe-Finish™ or Access Alliance Safe-Fini sh II™ photo- beams are connecte d.
12 NOTE: It is now necessary to turn on the power in order to change the Operatin g Mode (if applicable), progr am any changes de sired to th e operator’s other settings, check for proper performanc.
OPER A TION AND A DJUSTM ENT INSTRUCTIONS 13 IMPORT ANT SA F ETY INSTR UCTIONS FOR OWNER • Understand all of the operating features of y o ur door control sy s tem at the time of its installation. Your installin g dealer will demonstrate them for y ou.
14 OPER A TION AND A DJUSTM ENT INSTRUCTIONS Changing the Switch Selectable Operation Modes The following m o des are selected by setting the on-board dip switches, Figure 20 at right show s where the switches are located on the operator control board.
OPER A TION AND A DJUSTM ENT INSTRUCTIONS 15 TS Operation Open Button : Momentary activation; open override of closing door. Close Button : Momentary activation.
The sole noid operate d brake may require occasi onal adj ustmen t. Adjus tment is necess ary if door tends to drif t downward a fter reaching the open li mit . Foll ow t he inst ructi ons belo w a nd us e Figu r e 2 1 as a gui d e. (1) L oosen shoe a djustin g screw and bottom bracke t arm of solen oid.
remember to use the STOP butt on to stop the door at th e Fu lly Open Positio n. 4) Depress the limit nut retaining pla te (D) so it disengag e s from the slots in the lim it nuts. Turn the OPEN lim it nut (E) on the shaft until it engages the Open Limit Switch (A).
CLUTCH A DJUSTMENT The clutch serves to protect th e door, the electric operator and other equipment from undue stress or damage caused by starting forces and/or an obstruction to the door. It should be set no tighter than is necessary to sm oothl y and consistently move the door throughout its full range of trav el.
Following installation, the operator MUST be tested and respond correctly to all controls as specif ied on the w iri ng diagram. Keep personnel and equipm ent clear of the area beneath the door w hen performing the tests.
575 VOL TS, 3 PHASE SINGLE VOL TAGE MOTOR BL/BLK BL/BLK TO REVERSE MOTOR, SWITCH LEADS 1 & 3 L1 4 L2 YELLOW WHITE BLACK ORANGE BLUE RED Wire Nut Connect ion 3 BLUE (T ,J, H) YELLOW BLUE RED BLACK A.
WIRING DIAGRAM/SCHEMA TIC - THREE PH A SE 21 575 VOL TS, 3 PHASE SINGLE VOL T AGE MOTOR BL/BLK BL/BLK TO REVERSE MOTOR, SWITCH LEADS 1 & 3 L1 4 L2 YELLOW WHITE BLACK ORANGE BLUE RED Wire Nut Connection 3 BLUE (T ,J,H) YELLOW BLUE RED BLACK A.
FIGURE 24 - OPERA TOR DIMENSIONS 107093 OPER A TOR DIMENSIONS / NOTES 22 NOTES.
Ref Part # Descrip tion Assem blies A 106798 Frame Assembly w/Sh afts, AUD (1 /3 HP) 1074 12 Fram e Assembly w/Shafts, A UD (1/2 & 3/ 4 HP) C 11007 5 Clutch Shaf t Assembl y, AUD D 109 848 Driv e .
Manufacturer’s Lim ited Warranty Linear L LC warr ants its All star brand c ommercial door oper ators to be f ree from def ect in ma terial and w orkmanshi p for a peri od of tw o (2) years from the da t e of purch ase. To obtain service contact y our dealer.
デバイスAudi AUD-Sの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Audi AUD-Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAudi AUD-Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Audi AUD-Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Audi AUD-Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Audi AUD-Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAudi AUD-Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Audi AUD-Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAudi AUD-Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。