Presonus Audio electronicメーカーADl 600の使用説明書/サービス説明書
ページ先へ移動 of 19
USER’S MANUAL version 1.0 © 2005, P r e S onus Audio Electronics, Incorporated. All rights reserved..
WARRANTY PreSonus Limited Warranty PreSonus Audio Electronics Inc. warrants this product to be free of defects in material and workmanship for a period of one y ear from the date of original retail purchase. This warranty is enforceable onl y by the original retail purc haser.
TABLE OF CONTENTS 3 1 Overview 1.1 Introduction 4 1.2 Features 5 2 Controls & Connections 2.1 Front Panel Layout 6 2.3 Back Panel Layout 8 2.4 Power and Ground 8 3 Operation 3.1 Input Sources 9 3.2 Microphones 9 3.3 Instruments 9 3.4 Line input 9 3.
1 OVERVIEW 4 1.1 INTRODUCTION Thank you for purchasing the PreSonus ADL 600. The ADL 600 utilizes the highest quality components to insure optimum performance for an infinite period of time. We believe the ADL 600 to be an exceptional-sounding microphone preamplifier and an exceptional value.
OVERVIEW 5 1.2 FEATURES The following information is a summary of your ADL 600’s features: All Tube, Dual Transformer Microphone Pre-Amplifier . Your ADL 600 is a discrete Class A high voltage all t.
2 CONTROLS & CONNECTIONS 6 2.1 FRONT PANEL LAYOUT The front panel of the ADL 600 is laid out so that if you split the front panel down the middle the controls and metering for channel 1 are on the left hand side and the controls and metering for channel 2 are on the right hand side.
CONTROLS & CONNECTIONS 7 +48V : The 48 volts supplied by way of the XLR connector, provides power for condenser mics and any other devices requiring continuous phantom power through the XLR input. This power is supp lied at a constant level to prevent any degradation of audio quality.
CONTROLS & CONNECTIONS 8 2.2 BACK PANEL LAYOUT Connectors All Input and Output connectors are transformer balanced. XLR with the following wiring standard: X L R PIN 1 GND PIN 2 High (+) PIN 3 Low (-) NOTE: The LINE INPUT does not pass signal unless the INPUT selector switch is set to LINE on the front panel.
3 OPERA TION 9 3.1 INPUT SOURCES The ADL 600 can be used with a variety of input sources: microphones, instruments and line level devices. 3.2 MICROPHONES The ADL 600 works great with all types of microphones including dynamic, ribbon and condenser microphones.
OPERATION 10 3.5 HOOK UP DIAGRAMS The following hook up diagrams are provided to give you a few examples in connecting your ADL 600 for various recording applications: 1.
OPERATION 11 3. Keyboards, Sy nths and Drum Machines 4. Stereo buss signal conditioning during mix-dow n or stereo mastering.
OPERATION 12 3.6 APPLICATIONS The following are a few two-channel recording applications for you to get you started in using your ADL 600. These are by no means the only way to record these instruments. Microphone selection and placement is an art form.
OPERATION 13 2. Electric Guitar – Place a dynamic or ribbon microphone an inch or two away from the s peaker of the guitar amplifier. Experiment with exact location. If you are recording an amp with multiple speakers experim ent with each one to see if one sounds better than the others.
OPERATION 14 3. Acoustic Guitar – Place a small diaphragm condenser microphone pointed at the 12 th fret approximately eight inches away. Place a large diaphragm condenser microphone pointed at the bridge of the guitar approximately twelve inches fr om the guitar.
OPERATION 15 4. Bass Guitar (Direct and Speaker) Plug electric bass guitar into a passive direct box. C onnect instrument output from the passive direct box to a bass amplifier. Place a dynamic microphone an inch or two away from the speaker and connect microphone to ADL 600 microphone input.
OPERATION 16 5. Drum Overheads (XY example) – Place two small diaphragm condenser microphones on an XY stereo microphone holder (bar). Position microphones so that each microphone is at a 45 degree angle pointed down at the drum kit approximately seven or eight feet up.
OPERATION 17 6. Snare Drum – (top and bottom) Place dynamic microphone pointed at the center of the snare making sure drummer will not hit it. Place small diaphragm condenser microphone under the drum pointed at t he snares. Experiment with microphone placement of both microphones.
4 TECHNICAL 18.
TECHNICAL 19 4.2 TECHNICAL SPECIFICATIONS Input Impedance Microphone ............................................. Selectable, 150/300/900/1500 Ohm Balanced Line ...................................................................................... 2KOhm Instrument .
デバイスPresonus Audio electronic ADl 600の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Presonus Audio electronic ADl 600をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはPresonus Audio electronic ADl 600の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Presonus Audio electronic ADl 600の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Presonus Audio electronic ADl 600で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Presonus Audio electronic ADl 600を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はPresonus Audio electronic ADl 600の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Presonus Audio electronic ADl 600に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちPresonus Audio electronic ADl 600デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。