Radio ShackメーカーXL-110の使用説明書/サービス説明書
ページ先へ移動 of 20
Owner’s Manual Please read before using this equipment. XL-110 High Power Stereo Amplifier 12-2014.fm Page 1 Tuesday, May 9 , 2000 8:51 AM.
2 ˆ Contents Features ........... .............. .............. .............. .............. ................. .............. .............. ...... ........ .... 3 Preparation ......... .............. .............. .............. .............. ...
3 Features ˆ Features Your RadioShack High-Power Stereo A mp l i fi - er produces a total of 110 wa tts to give add- ed punch and power to your ve hicle’s existing auto sound system. The amplifier produces up to 55 watts per channel of clean, powerful sound at all a udio frequencies with mini mum distortion.
4 Preparation ˆ Preparation SUPPLIED HARDWARE Your amplifier comes with the followi ng items. Be sure you locate everything l isted before you store or dispo se of the pa cki n g mate ri al s. BEFORE Y OU BEGIN THE INSTALLATION Before you install your amplifier, read all the instructions in this owner’s manual.
5 Preparation Warning: The amplifier gets very ho t while it is on. Do not touch the a mplifier or place flammable objects near it w hile it is on. Preparing the Mounting Area In addition to th e supp.
6 Preparation Cautions: • For added safety and to protect your amplifier and auto sound system, dis- connect the cable from your vehicle’s negative ( – ) battery terminal be fore you begin. • Be sure your speakers can ha ndle as much as 1 10 watts of power (55 watts per channel).
7 Preparation using one of the supplied twist-on termi- nal connectors. This connection turns on the ampl ifier when you turn on the auto sound sys- tem, and turns off the amplifier when you turn off the auto sound system.
8 Connecting Inputs ˆ Connecting Inputs LOW-LEVEL INPUTS You can connect your auto sound system’ s low-level line out jacks to the amplifier’s low-level line in jacks. If your auto sound system does not have low-level line out jacks, see “High-Level (Speaker Wire) Inputs” on Page 9 to connect your amplifier.
9 Connecting Inputs HIGH-LEVEL (SPEAKER WIRE) INPUTS If your auto sound system does not have low-level line out jacks but has o nly speaker outputs, connect your auto sound system’s speaker outputs to the ampli fier’s HIGH IN- PUT jacks.
10 Connecting Inputs Four Speaker Outputs Floating Grou nd Connection Common Ground Con nection Auto Sound System Left Rear + Speaker Left Rear – Speaker Right Rear+ Speaker Right Rear– Speaker Wh.
11 Connecting Inputs Two Speaker Outputs Floating Grou nd Connection Common Ground Con nection Auto Sound System Left + Speaker Left – Speaker Right + Speaker Right – Speaker White/Black Gray/Black White Gray Auto Sound System Right + Speaker Left + Speaker Common Gray White/ Black White Gray/ Black 12-2014.
12 Connecting Inputs CONNECTING SPEAKERS You can connect two spea kers or a subwoof- er to the amplifier and your auto sound sys- tem. • If you are connecting two speakers, fo l- low Steps 1–3 under “Preparing the Speaker Wires” then see “Co nnecting T wo Speakers” on Page 13 to connect the speakers to the amplifier .
13 Connecting Inputs Connecting Two Speakers 1. Use a screwdriver to connect the left speake r ’s positive (+) wire to the ampl ifier ’s SPEAKER L (+ ) terminal. 2. Use a screwdriver to co nnect the left sp eaker ’s negative (–) wire to the ampl ifier ’s SPEAKER L (–) terminal.
14 Completing the Installation 2. Use a screwdriver to connect the sub- woofer ’s negative ( – ) wire to the ampli- fier ’s negative (–) terminal for th e same channel you connected in Step 1.
15 Operation Note: If yo u have not alre ady done so, be sure to mark each wire with the name of the terminal you will reconnect it to. 3. Using the mounting holes on the ampli- fier as a guide, mark the positions for the mounting holes. 4. Drill 9 / 64 -inch (3.
16 Troubleshooting 4. T u rn up the auto sound system’ s volume control until the sound begi ns to distort. Then immediately turn the volu me down to a point just be fore where the distor- tion began.
17 Troubleshooting If you still have problems, disconnect the amplifier and take it to your local Rad ioShack store for assistance. No Sound (continued). The amplifier is not properly connected to your auto sound system/vehicle. Check all connections.
18 Care ˆ Care To enjoy your amplifier for a long time: • Keep the amplifier dry . If it gets wet, wipe it dry immed iately . • Use and store the amplifier only in nor- mal temperature environments. • Handle the amplifier gently and care- fully .
19 Specifications ˆ Specifications Output Power @ 14.4 VDC 1kHz ..................................... 35 Watts × 2 @ 4 Ohms, 20–20 kHz, 0.5% TH D 55 W atts × 2 @ 4 Ohms, 20–20 kHz, 10% T HD 40 W atts × 2 @ 2 Ohms, 20–20 kHz, 1% T HD Frequency Response .
12-2014 05A00 Printed in China RadioShack A Division of Tandy Corporation Fort Worth, Texas 76102 Limited One-Y ear W arranty This product is warranted by RadioShack against manufactu ring defects in .
デバイスRadio Shack XL-110の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Radio Shack XL-110をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRadio Shack XL-110の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Radio Shack XL-110の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Radio Shack XL-110で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Radio Shack XL-110を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRadio Shack XL-110の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Radio Shack XL-110に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRadio Shack XL-110デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。