Ramsey ElectronicsメーカーQAMP40の使用説明書/サービス説明書
ページ先へ移動 of 20
QAMP-40 • 1 Ramsey Electronics Model No. QAMP40 Need a little extra boost for your QRP rig? Believe it or not, 20 watts is only about an ‘S’ unit below a 100 watt ri g! This nifty little amp will add some “punch” to any QRP transmitter.
QAMP-40 • 2 P A RTI A L LIST OF A V A IL ABLE KITS RA M SEY T RA N SMIT TE R K ITS • FM10, FM25B FM Stereo Transmi tters • FM100 Super Pro FM Transm itter • MR6 Model Rocket Tracking Transmitt.
QAMP-40 • 3 Ramsey Publication No. MQAMP40 Price $5.00 TABLE OF CONTENTS Introduction to the QAMP40 ........... 4 How it works ............... .................... 4 Parts list .... ....................... .............. 5 Tips and notes .... ......
QAMP-40 • 4 INTR ODU CTIO N The Ram sey QAMP series of QRP power ampl ifiers are com pact 10 to 20 watt RF amplifiers for QRP CW transmitters. These amplifiers are made to be driven by transmitters in the ½ to 2 watt range. Built-in to the power amplifier is a sensitive T-R relay which w ill switch the unit in and out of the antenna line.
QAMP-40 • 5 PARTS LIST FOR THE QA MP40 QRP POWER AMPLIFIER CAPACIT O RS: 1 100 to 220 µ f electroly tic capacito r [C1] 1 10 µf el ectroly tic cap acitor [C2] 4 .
QAMP-40 • 6 "THE RAMSEY LEARN-AS-YOU-BUILD ASSEMBLY STRATEGY" Take a look at the part s layout diagram . There is quite a lot to the construc tion of the QAMP40. It's easier than it seems once y ou get going, especially after you have installed a few of the "landmark" components.
QAMP-40 • 7 • Insert the part, oriented correctly, into its correct holes in the PC board. If helpful, gently bend the part’s wire leads or tabs to hold it in place, with the bod y of th e part snugly against the top side (component side) of the PC board.
QAMP-40 • 8 16. In stall diode D4, 1N4002 style blac k epoxy diod e. Check positioning of the banded end. 17. Install jumper JMP2. Use a piece of scrap componen t lead wire bent into a "staple" shape and inserted into the board like a component.
QAMP-40 • 9 30. Install C12, another .001 µf disc capacitor (marked .001 or 102). 31. Install C8, .1µf disc capacitor (marked .1 or 104). These last four part s (R8,9 and C11, 12) form parasitic suppress ion networks across each transistor to suppress any tendency for high frequency oscillation in the power amplifier.
QAMP-40 • 10 We're almost finished. All we need to do now is install a few remaining parts that have to be handmade - for that "old-world craftsmanship" touch ! We 'll pre pare all those part s now for fu rther assem bly .
QAMP-40 • 11 Tin each end w ith solder as before. Tin all the way up to the core body. This winding is the primary of transformer T2. 44. Cut off another length of wire , 8 inches long. Wind 1 turn through the core, loop out 1 inch, twist together and run o ne more turn through the core, continuing on in the same direction as before.
QAMP-40 • 12 47. Locate the smaller transformer (T2) and install it snugly on the PC board. 48. Install the larger transformer (T1) into the indicated location on the PC board.
QAMP-40 • 13 3. Connect a dummy load to J1, the amplifier RF output. In a pinch, a light bulb m ay be used - see the section, "Ve rifying RF Power Output." 4. Temporarily install a jumper from the collector of Q3 to ground . 5.
QAMP-40 • 14 VERIFYING TRANSMITTER RF OU TPUT The most important thing to know is wh ether your transmitter is delivering some meas urable and reassuri ng level of RF pow e r. Then y ou can continue on to adding the QRP a mplifier and checking out the w h ole set-up .
QAMP-40 • 15 KB4ZGC on how to make a highly accurate yet inexpensive dummy load and wattmeter capable of showing 1/10 -watt differences in RF power. If y ou use a wattmeter characterized for the HF .
QAMP-40 • 16 check are the bias circuitry and RF path through the relay. The amplifier should draw about ¼ amp with no signal applied. If you see m ore than that, recheck the bias setting (see the secti on "INITIAL TESTS").
QAMP-40 • 17 case and hardw are set w i ll give your unit that nice finished look and increase its resale value. These sturdy black instrument cases a r e supplied w ith n eatly lettered front and rear panels, switch knobs, rubber feet and mounting screws.
QAMP-40 • 18.
QAMP-40 • 19 The Ramsey Kit Warra nty Please read carefully BEFORE calling or writing in about your kit. Most problems can be solve d without contacting the factory . Notice that thi s is not a "fine print" w ar ranty. W e w ant you to unders tand your righ ts and ours too ! All Ramsey kits w ill work if assembl ed properly .
QAMP-40 • 20 Q A MP40 20 WATT LINEAR AMPLIFIER Quick Re ference Page Gu ide Introduction to the QAMP40 .......... .4 How it works ........................... ........4 Parts list ................. ........................ .5 Tips and notes .........
デバイスRamsey Electronics QAMP40の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Ramsey Electronics QAMP40をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRamsey Electronics QAMP40の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Ramsey Electronics QAMP40の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Ramsey Electronics QAMP40で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Ramsey Electronics QAMP40を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRamsey Electronics QAMP40の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Ramsey Electronics QAMP40に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRamsey Electronics QAMP40デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
