RaymarineメーカーST40の使用説明書/サービス説明書
ページ先へ移動 of 45
Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company.
ST40 Compass Instrument Owner’ s Handbook Document number: 81161_2 Date: 1st May 2001 161_2cov.p65 01/05/01, 16:50 1.
Copyright © Raymarine Limited 2001 161_2cov.p65 01/05/01, 16:50 2.
Preface i Important information WARNING Although your ST40 instrument is designed to give accurate and reliable performance, it should serve only as an aid to navigation and should never lead to the erosion of good seamanship. Always maintain a permanent watch and be aware of situations as they develop.
ii ST40 Compass Instrument Owner ’ s Handbook 161_2pre.p65 01/05/01, 16:50 2.
Preface iii Contents Important information .......................................................... i W ARNING ......................................................................... i EMC conformance ..............................................
i v ST40 Compass Instrument Owner ’ s Handbook Chapter 3: Installation ......................................................... 11 3.1 Planning your installation ......................................... 11 EMC installation guidelines .............
Preface v Pr eface Thank you for purchasing a Raymarine product. We are sure your ST40 instrument will give you many years of trouble-free operation. This instrument is designed to provide reliable performance, even under the most demanding conditions.
v i ST40 Compass Instrument Owner ’ s Handbook P arts supplied Fluxgate compass transducer D4771-2 ST40 Compass Instrument Owner's Handbook Worldwide Distributors ST40 Compass instrument F ixing stud T humb nut Gask et 1 m (3 ft) power cable Instrument Cover Owner ’ s Handbook.
Chapter 1: Operation 1 Chapter 1: Oper ation 1.1 Introduction Your ST40 Compass instrument: • Provides true and magnetic bearing information. • Enables a locked bearing to be defined either manually, or automatically by a course computer.
2 ST40 Compass Instrument Owner ’ s Handbook NORMAL OPERA TION Compass heading D4772-2 Note: T he Off course alarm screen is temporary and will time-out to the Compass heading screen after 5 seconds .
Chapter 1: Operation 3 Backlighting and contr ast adjustment During normal operation, press During normal operation, press T he current backlighting level is displayed.
4 ST40 Compass Instrument Owner ’ s Handbook 1.3 Scr een descriptions Compass heading scr een COMP ASS Cardinal points (North flashing) Either M (magnetic) or T (true) Current heading ST40 Press to .
Chapter 1: Operation 5 1.4 Alarms Off course active alarm Heading error Current heading STEER D4773-2 COMP ASS ST40 Enabling/disabling alarm You can enable or disable the off course alarm function (i.
6 ST40 Compass Instrument Owner ’ s Handbook 161_2c01.p65 01/05/01, 16:51 6.
Chapter 2: Maintenance and Fault Finding 7 Chapter 2: Maintenance and F ault Finding 2.1 Maintenance Servicing and safety • Raymarine equipment should be serviced only by authorised Raymarine service technicians. They will ensure that service procedures and replacement parts used will not affect performance.
8 ST40 Compass Instrument Owner ’ s Handbook Instrument Certain atmospheric conditions may cause a small amount of condensation to form on the instrument window. This will not harm the instrument and will clear after the instrument has been switched on for a short period.
Chapter 2: Maintenance and Fault Finding 9 Action Recharge your vessel ’ s battery as soon as possible D4755-2 Action Check fuse/circuit breaker. Check power supply. Check SeaTalk cabling and connector security. D4777-2 COMP ASS ST40 Action Check the condition of the fluxgate compass transducer cable and the security of the connections.
10 ST40 Compass Instrument Owner ’ s Handbook A group of SeaTalk instruments not working Action Check the security of SeaTalk connectors between functioning and non-functioning instruments. D4758-2 WIND ST40 WIND ST40 WIND ST40 Assistance If you are unable to rectify any problem, please contact your local Raymarine Dealer for assistance.
Chapter 3: Installation 11 Chapter 3: Installation This chapter describes how to install the ST40 Compass instrument, and associated Fluxgate Compass transducer. 3.1 Planning your installation Determine the best positions for both transducer and instrument, such that the EMC installation guidelines and the Site requirements (below) are satisfied.
12 ST40 Compass Instrument Owner ’ s Handbook • The equipment is supplied from a different battery from that used for engine start. Voltage drops below 10 V in the power supply to our products, and starter motor transients, can cause the equipment to reset.
Chapter 3: Installation 13 57 mm (2.25 in) D4643-3 Note: If you intend fitting a nonstandard transducer, extra tools may be required. Site requir ements Fluxgate Compass transducer The Fluxgate Compass transducer should be positioned as near as possible to the pitch/roll centre of the vessel, as shown in the shaded areas below.
14 ST40 Compass Instrument Owner ’ s Handbook The Fluxgate Compass transducer must also be sited: • At least 0.8 m (2 ft 6 in) away from the vessel's steering compass to avoid deviation in both compasses. • On a bulkhead below deck. Note: On steel vessels the Fluxgate Compass transducer can be mounted above deck.
Chapter 3: Installation 15 3.2 Procedur es Adapt these procedures as appropriate, to suit your individual requirement. CAUTION: Where it is necessary to cut holes (e.g. for cable routing and instrument mounting), ensure that these will not cause a hazard by weakening critical parts of the vessel’s structure.
16 ST40 Compass Instrument Owner ’ s Handbook 76 mm (3 in) 76 mm (3 in) D729-6 If you are not sure of the magnetic suitability of the chosen location, carry out a survey of the site as follows: 1. Temporarily fix a simple hand bearing compass at the intended location.
Chapter 3: Installation 17 Connections to the instrument You can connect your instrument: • Directly to the compass transducer as a stand-alone master instrument. When connected in this manner, the instrument must be connected to a suitable power source using the 1 m (3 ft) power cable provided.
18 ST40 Compass Instrument Owner ’ s Handbook Stand-alone connections CAUTION Ensure that the power supply for each stand-alone ST40 instrument is protected by a 3 A fuse or circuit breaker.
Chapter 3: Installation 19 SeaTalk connections CAUTION When instruments are connected to SeaTalk, ensure that the power supply for the SeaTalk 12 V line is protected by a 5 A fuse or circuit breaker.
20 ST40 Compass Instrument Owner ’ s Handbook 2 Cut hole 57 mm (2.25 in) cutter D4760-1 P eel protective sheets from gasket 3 D4770-1 4 Stick gask et to rear of instrument D4761-1 161_2c03.
Chapter 3: Installation 21 D4819-1 5 Screw stud into instrument D5030-1 6 F eed cables through clamping bracket, connect cables then secure instrument with brack et and thumb nut Desktop Mounting Bracket An optional Desktop Mounting Bracket (Part No.
22 ST40 Compass Instrument Owner ’ s Handbook D4646-1 To bracket mount your ST40 instrument, do so in accordance with the Instruction Sheet , which is included with the Desktop Mounting Bracket.
Chapter 4: Calibration 23 Chapter 4: Calibr ation 4.1 Introduction The procedures in this Chapter must be carried out before the equipment is used operationally, to optimise the performance of the instrument with the vessel. Calibration information is presented in flow chart form.
24 ST40 Compass Instrument Owner ’ s Handbook USER CALIBRA TION Entry screen Set compass heading response for approximately 2 seconds hold down and 15 (fast) 1 (slow) D4780-2 COMPASS Increase Decrea.
Chapter 4: Calibration 25 4.3 Intermediate calibration Intermediate calibration enables you to: • Check the instrument software version. • Check the instrument status - either master (shown as RPTR NO ) or repeater (shown as RPTR YES ). You cannot make any adjustments in Intermediate calibration.
26 ST40 Compass Instrument Owner ’ s Handbook DEALER CALIBRA TION CAUTION: Do NOT switch the Boat Show mode on. This function must only be used for demonstration purposes .
Instrument Specification 27 Instrument Specification Supply voltage: 10 V to 16 V dc. Current consumption (12 V supply): 20 mA typical. 60 mA with maximum backlighting. Operating temperature: 0 ° C to +70 ° C. Interfaces: SeaTalk. Overall dimensions: 126 mm x 70 mm x 38 mm (5.
28 ST40 Compass Instrument Owner ’ s Handbook 161_2spe.p65 01/05/01, 16:52 28.
Glossary 29 Glossary EMC Electromagnetic Compatibility. M Metres. MOB Man overboard. Response The rate at which an instrument responds to changes in heading.
30 ST40 Compass Instrument Owner ’ s Handbook 161_2glo.p65 01/05/01, 16:52 30.
Index 31 Index A Alarms indications 5 man overboard 5 off course 5, 27 silencing 1 Aligning heading 24 B Backlighting 3 Boat show mode 25 C Calibration 23 – 26 Dealer 25 – 26 Intermediate 25 setti.
32 ST40 Compass Instrument Owner ’ s Handbook L Linearising transducer 24 Locked heading 2 auto 2 response 24 screen 4 Low battery indication 9 M Maintenance 7 – 8 Man overboard alarm 5 O Off cour.
D4800-1 TO P Cut out shaded area only Cut out hole 57 mm (2.25 in) diameter ST40 Instrument T emplate 161_2tem.p65 01/05/01, 16:52 33.
161_2tem.p65 01/05/01, 16:52 34.
Docume nt n umber: 84064- 8 Apri l 2001 Limited Warr a nty Certifi cate Raymarine warrants each new Light Marine/Dealer Distributor Pr oduct to be of good materi als and workmanship, and will re pair .
Factory Service Centers United States of America UK, Eur ope , Middle East, F ar East Raymarine In c 22 Cott on Road , Unit D Nashu a, NH 030 63-4219 , USA Raym ar ine Ltd Anchorage P ark, P ortsmouth PO3 5TD , Englan d T ele phone: +1 603 881 52 00 F ax: +1 603 864 4756 www .
デバイスRaymarine ST40の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Raymarine ST40をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはRaymarine ST40の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Raymarine ST40の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Raymarine ST40で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Raymarine ST40を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はRaymarine ST40の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Raymarine ST40に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちRaymarine ST40デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。